RoadVitals

2012 Altec Aerial Device Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
16
Newest Aug 29, 2025
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0

Recall campaigns

16 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

25V562000

STRUCTURE:FRAME AND MEMBERS

Aug 29, 2025
903 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain 2011-2025 Aerial Device, Digger Derrick, and 2022-2025 Service Body vehicles. The cable step wire rope assembly may be improperly secured, which can allow the cable entry step to detach from the vehicle.
The risk: A cable step that fails during use increases the risk of injury.
The remedy: Altec will provide owners with instructions to inspect the cable crimps. If the cables are improperly crimped, Altec will provide instructions and a kit to replace the wire rope assemblies. Repairs will be performed free of charge. Owner notification letters were mailed October 24, 2025. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN-3246.
Altec Industries, Inc.Manufacturer number CSN-3246View on NHTSA.gov
24V015000

ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES

Jan 11, 2024
437 units potentially affected
The defect: Altec Industries, Inc. (Altec) is recalling certain 2004-2023 AT Series aerial devices. The cables in the engine compartment may contact the vehicle's hood, damaging the cables and causing a short circuit.
The risk: A short circuit increases the risk of a fire.
The remedy: Altec will inspect and relocate the cables and fuse blocks, free of charge. Owner notification letters are expected to be mailed March 8, 2024. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN-3142.
Altec Industries, Inc.Manufacturer number CSN-3142View on NHTSA.gov
21V884000

EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER:TURNTABLE; STRUCTURE:FRAME AND MEMBERS

Nov 15, 2021
4,055 units potentially affected
The defect: Altec Industries, Inc. (Altec) is recalling certain 2012-2016 AT200A aerial devices. Cracks may develop in the legs of the mounting frame, which can cause the mounting frame side plate to break.
The risk: A broken side plate may result in pedestal and truck frame separation, increasing the risk of injury.
The remedy: Altec will repair the side plates as necessary, or provide a repair kit, free of charge. Owner notification letters were mailed January 13, 2022. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 840.
Altec Industries, Inc.Manufacturer number CSN 840View on NHTSA.gov
21V736000

EQUIPMENT:MECHANICAL:BOOM/CRANE/LADDER:TURNTABLE; STRUCTURE:FRAME AND MEMBERS

Sep 23, 2021
2,115 units potentially affected
The defect: Altec Industries, Inc. (Altec) is recalling certain 2011-2016 AT200A aerial devices. Cracks may develop in the legs of the mounting frame, which can cause the mounting frame side plate to break.
The risk: A broken side plate may result in pedestal and truck frame separation, increasing the risk of injury.
The remedy: Altec will repair the side plates as necessary, or provide a repair kit, free of charge. Owner notification letters were mailed on October 13, 2021. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is CSN 836.
Altec Industries, Inc.Manufacturer number CSN 836View on NHTSA.gov
21V409000

EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY

Jun 1, 2021
1,977 units potentially affected
The defect: Altec Industries, Inc. (Altec) is recalling certain 2005-2021 A65, A70, A75, A72-T, A77-T, and A82-T vehicles. The lower and upper boom raise spools can shift after releasing the joystick or control interlock.
The risk: Unintended movement of the lower and upper booms increases the risk of injury.
The remedy: Altec will install a jumper hose and check valve into the boomtip tank lines and replace the overcenter blocking cartridge with an internally referenced drain path, free of charge. Owner notification letters were mailed on July 28, 2021. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 823.
Altec Industries, Inc.Manufacturer number CSN 823View on NHTSA.gov
19V602000

EQUIPMENT:MECHANICAL:WINCH

Aug 15, 2019
23 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain 2012-2019 Altec AM60E, AA55E, AH75/85/100, AH125, and AH150 Aerial Devices. The recovery winch valve may allow the winch to lift more than it is rated for.
The risk: If the recovery winch attempts to lift more than it is rated for, it can increase the risk of an injury or death.
The remedy: Altec will notify owners, and instruct owners to inspect the winch pressures and install an external pressure relief valve, if necessary, free of charge. The recall began October 7, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 734.
Altec Industries Inc.Manufacturer number CSN 734View on NHTSA.gov
19V483000

SERVICE BRAKES, AIR

Jun 21, 2019
957 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain 2003-2019 Altec TA45, TA50, TA55, TA60, L37, L39, LRV, LR7, A-T40C, T40P and AP45 vehicles equipped with air-cushioned pintle hitch and/or accessory air components. The accessories utilizing chassis air supply may be missing pressure protection valves. The accessory lines may not prevent service brake line pressure loss due to failure or leakage in the accessory air system. Additionally, the air cushioned pintle hook may have been connected to the incorrect air lines. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems."
The risk: Loss of service brake pressure can increase the risk of a crash.
The remedy: Altec will notify owners, and dealers will inspect the pressure protection installation and repair any unit that does not pass inspection, free of charge. The recall began August 15, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 724.
Altec Industries Inc.Manufacturer number CSN 724View on NHTSA.gov
18V552000

STRUCTURE

Aug 22, 2018
530 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain 2008-2018 Aerial Devices equipped with aluminum work platforms. The platform mounting holes may fail, causing the platform to move unexpectedly.
The risk: If the platform moves unexpectedly, it can increase the risk of injury.
The remedy: Altec will notify owners, and dealers will install a bracket reinforcing kit, free of charge. The recall is expected to begin October 17, 2018. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 689.
Altec Industries Inc.Manufacturer number CSN 689View on NHTSA.gov
18V348000

TRAILER HITCHES

May 29, 2018
201 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain 2012-2018 Altec LS63 and LS87 aerial devices equipped with a pintle hook mounted into the Class 3 receiver tube. This towing combination was shipped without a placard that provides the maximum allowable towing limit, possibly resulting in the receiver tube being overloaded.
The risk: An overloaded receiver tube could detach, increasing the risk of a crash.
The remedy: Altec will notify owners, and provide them with a placard that states the limit of the receiver tube assembly as 600lbs vertical load, and 6,000lbs towing capacity, free of charge. The recall began on July 25, 2018. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 684.
Altec Industries Inc.Manufacturer number CSN 684View on NHTSA.gov
18V110000

EQUIPMENT

Feb 14, 2018
18,000 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain 1997-2017 LRV, and LR7 Aerial devices. The platform leveling yoke may fail, possibly causing an occupant to fall from the platform.
The risk: Failure of the platform leveling yoke can cause the occupant of the platform to fall out, increasing their risk of injury.
The remedy: Altec will notify owners, and will inspect the leveling system to verify the correct alignment, replacing any improperly aligned yokes, free of charge. The recall began on April 11, 2018. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 672.
Altec Industries Inc.Manufacturer number CSN 672View on NHTSA.gov
17V560000

EQUIPMENT

Sep 11, 2017
143 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain 2011-2017 Altec LS63 Aerial Devices. The jib mast on these vehicles may bend under load.
The risk: The jib mast may bend and fail, increasing the risk of injury to those nearby.
The remedy: Altec will notify owners and test the jib mast, replacing any that fail, free of charge. The recall began on October 13, 2017. Owners may contact Altec customer service at 1-205-991-7733. Altec's number for this recall is CSN 664.
Altec Industries Inc.Manufacturer number CSN 664View on NHTSA.gov
15V473000

EQUIPMENT

Jul 28, 2015
2,514 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain model year 2006-2015 Aerial Devices manufactured from June 1, 2006, through April 1, 2015. The affected aerial devices outrigger interlock control system may not detect proper deployment of the outriggers, allowing for instability of the boom.
The risk: If the aerial device is operated while the outrigger is not properly deployed it can cause instability of the boom, increasing the risk of person injury or death.
The remedy: Altec will notify owners, and dealers will replace the aerial device with a new outrigger interlock module, free of charge. The recall began on September 4, 2015. Owners may contact Altec customer service at 1-205-991-7733. Altec's number for this recall is CSN 625.
Altec Industries Inc.Manufacturer number CSN 625View on NHTSA.gov
15V101000

ELECTRICAL SYSTEM

Feb 23, 2015
5,142 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain model year 2012-2014 Digger Derrick and Aerial Device vehicles manufactured October 1, 2012, to June 30, 2014, and mounted on Freightliner chassis. In the event of a short circuit condition, the 30 amp breaker to the trailer relay module may react too slowly to prevent the module from overheating.
The risk: If the module overheats, there is an increased risk of a fire.
The remedy: Altec will notify owners, and dealers will replace the 30 amp circuit breaker with a 20 amp one, free of charge. The recall began on April 17, 2015. Owners may contact Altec customer service at 1-800-860-0183. Altec's number for this recall is CSN 612.
Altec Industries Inc.Manufacturer number CSN 612View on NHTSA.gov
15V096000

EQUIPMENT

Feb 19, 2015
3,889 units potentially affected
The defect: Altec Industries, Inc. (Altec) is recalling certain model year 2011-2014 Aerial Devices, models L36A, LRV, and LR7, manufactured June 1, 2011, to September 30, 2014, and built with Texas Hydraulics upper boom drive cylinders. In the affected aerial devices, the cylinder base end lug casting may develop cracks.
The risk: If the cylinder lug castings crack, they may fail, resulting in unintended movement of the boom, increasing the risk of personal injury or death to the aerial device user or those nearby.
The remedy: Altec will notify owners, and dealers will inspect the cylinders for specific casting suspect lots. If both upper boom drive cylinders are not of the suspect lots, no further action is required. If a cylinder is found to be of one of the suspect lots, it will be inspected for visible cracks. If cracks are found the unit should be removed from service immediately and the cylinder will be replaced. If no cracks are found, the unit will be scheduled for magnetic particle inspection of the cylinder lug within 60 days. All of these actions will be performed free of charge. The recall began on April 6, 2015. Owners may contact Altec customer service at 1-800-860-0183. Altec's number for this recall is CSN 611.
Altec Industries Inc.Manufacturer number CSN 611View on NHTSA.gov
14V745000

EQUIPMENT

Nov 21, 2014
1,907 units potentially affected
The defect: Altec Industries Inc. (Altec) is recalling certain model year 1999-2014 aerial devices models A65, A70, A75, A72-, A/77-T, A82-T, A72-TE88, and A77-TE93 manufactured January 1, 1999, to July 15, 2014. The affected aerial devices may have an improperly set hydraulic pressure transducer which relieves excessive backpressure in the hydraulic tank circuit.
The risk: In cooler temperatures, the improperly set hydraulic pressure transducer may result in inadvertent boom movement, increasing the risk of injury to the occupant or those nearby.
The remedy: Altec will notify owners, and dealers will replace and install a pressure switch, free of charge. The recall began in January 16, 2015. Owners may contact Altec customer service at 1-205-991-7733. Altec's number for this recall is CSN 609.
Altec Industries Inc.Manufacturer number CSN 609View on NHTSA.gov
14V503000

ELECTRICAL SYSTEM:12V/24V/48V BATTERY

Aug 15, 2014
51 units potentially affected
The defect: Altec Industries, Inc. (Altec) is recalling certain model year 2000-2013 Aerial Device and Digger Derrick trucks, equipped with Sure Power Battery Equalizers containing a particular epoxy sealing, aka 'potting', compound. The specific potting compound used in the subject products for insulation was found to be capable of conducting electricity after being exposed to heat.
The risk: Once electrically conductive, the material is capable of melting and burning, increasing the risk of a fire.
The remedy: Altec will notify owners, and dealers will replace any affected battery equalizer, free of charge. The recall is expected to begin in September 2014. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 603.
Altec Industries Inc.Manufacturer number CSN 603View on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Elsewhere on this vehicle

Data sources