2005 Chevrolet Corvette Problems

The contact owns a 2005 Chevrolet Corvette. The contact stated that while operating the vehicle, the low-beam headlights malfunctioned and failed to illuminate as needed. The contact stated that the failure was intermittent. The vehicle was taken to the local mechanic, who was unable to duplicate the failure. The vehicle was not repaired. The local dealer and manufacturer were notified of the failure and informed the contact that the VIN was not included in NHTSA Campaign Number: 14V251000 (ELECTRICAL SYSTEM, EXTERIOR LIGHTING). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 123,000.

This lead to an injury accident which totaled the car. I have documentation stating that the recall was fixed, but after I moved to Germany with the Army, the recall regularly activated the active handling when not needed (e.g parking) but then when we started slipping, the active handling did not engage and we crashed, totaling the car. The airbags did not engage even though the car played pinball on both sides of the autobahn. If we were going any faster, we would have died.

As I'm driving, the brakes are deployed "hard" without any action on my part. "CHECK ACTIVE HANDLING SYSTEM" shows up on the screen. I have not het had the vehicle inspected.

My car has been broken for over a year now. It has been to the dealership for the main engine wiring harness part number 19115750 which is unique to the 2005 and 2006 corvette. The failure causes several different problem. It keeps the TCM from which is the traction control module which adjust speed and traction to the wheels which is design to help drivers keep their cars under control. Without this system the car will loose traction and can cause it to go off the road. The second issue with the harness is it can put the car limp mode which restricts the speed to under 40mph which if you are driving and trying to excel into traffic this system will come in without notice and put you into a situation where if you are trying to merge or just go when the light changes it will only go like 5 mph causes the cars behind you to run into the rear of your vehicle and when if fail and you are pulling into traffic it causes your car to be in a direct line of impact with oncoming vehicle. The engine harness also provides power to the transmission via the ECM which keeps it from providing enough power to run the transmission control computer. This will make your car not go into gear or make it go completely out so without a transmission your car won’t move at all. This happens without notice. Now GM doesn’t make a replacement harness anymore making your vehicle unusable. GM also wants between 7k and 10k to make a harness for the vehicle. This doesn’t include installation. This makes the owners like myself have to seek other means to repair the vehicle. Like having a custom harness made for vehicle. Since GM only made this harness for 2 years it has been impossible for me to get my vehicle repaired at any cost. Making owner to make decisions that are unfair to owners. Like sell the car for scrap Paid the expensive repair which is like half the value of the car. Trade the car and lose thousands of dollars if you can find a dealership willing to take it

The contact owns a 2005 Chevrolet Corvette. The contact stated that while operating the vehicle, the low-beam headlights malfunctioned and failed to illuminate as needed. The contact stated that the failure was intermittent. The vehicle was taken to the local mechanic, who was unable to duplicate the failure. The vehicle was not repaired. The local dealer and manufacturer were notified of the failure and informed the contact that the VIN was not included in NHTSA Campaign Number: 14V251000 (ELECTRICAL SYSTEM, EXTERIOR LIGHTING). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 123,000.

The contact owns a 2005 Chevrolet Corvette. The contact stated while driving 45 MPH, the headlights were flickering and then became inoperable. The fuse box was melted. There was smoke detected from underneath the hood. There were no warning lights illuminated. The contact stated that the failure was related to NHTSA Campaign Number: 14V251000 (Electrical System, Exterior Lighting). The vehicle was towed to a local dealer, where it was diagnosed that the fuse box needed to be replaced. The vehicle was not repaired. The manufacturer was contacted, and informed the contact that the part was no longer produced. The failure mileage was approximately 80,000.

steering wheel lock car cannot start and this can happen while driving and could cause a accident chevy knows of problem and has been recalled but has not solved the problem knowed as steering wheel lock

2005 Corvette coupe, manual trans, Z51. Intermittent problem: Electronic steering column will not unlock when attempting to start or will not lock on shutdown. Vehicle inoperable, sometimes in potentially hazardous situations e.g., late night in parking lot, and compromised anti-theft feature. Possibly relevant: When parked but steering failed to lock, continuous battery draw is 4 amps, which might contribute to the "dead battery syndrome" that 2005 M6 Corvettes are known for. Hard to separate the two issues since either way the starter will not engage. Problem has existed since new (2005) but has gotten progressively worse. GM nonresponsive to multiple owner complaints. Aftermarket "Column Lock Bypass" work-arounds have been sold for this problem, but they are potentially dangerous since they simply spoof the BCM into thinking that the lock is fully released when it is simply unpowered and can easily move into a partially locked position with vibration and time. This is what I recently observed that motivated this safety complaint. GM finally issued a recall in 2018 (13 years after MY) for this problem, but for some reason did not include manual transmission cars in the recall, possible because production was small compared with automatics. But from internet forums, it is clear that this problem affects all 2005 M6 Corvettes.

Brake transmission interlock failed. Car wouldnt shift out of park.

The transmission shifter lock starts to sporadically not release keeping transmission in park (online many say this is a very common problem for 2005-08s, maybe more years), this could strand someone.

The active handling applies itself with normal non aggressive driving. When activated the brakes apply and lock up, this has happened in low speed turns at intersections and even when driving straight. I have had the vehicle to the dealership to resolve as this is a major safety concern leaving the car locked up in the middle of an intersection. They stated it was the sensor behind the steering wheel and they fixed it but the problem still persists. Secondly the driver seat has begun moving on its own and inching me closer to the steering wheel with no interference with the button while driving. I have since disconnected the seat fuse to prevent collision from improper driver positioning.

I purchased my 2005 Corvette C6 from a used car dealership on 4/30/2023. The car was fine for the first week. The second week I began getting a lot of error codes specifically: Service Active Handling System Service Traction Control Service ABS Shocks Inoperative Service Fuel System. At times it would go into limp mode. I would find a safe place to pull off. I would shut the car off and it would not restart. I would check the relays under the hood and the passenger floorboard. Eventually it would restart and drive again until the next time. I have replaced the following components: Battery cables with factory replacement New Battery, twice New high output alternator and a new belt. These items solved the many codes. Now I get Service Traction System, and the traction control shuts off. When this happened last, I got a P0101 MAF sensor error. Replaced the MAF Sensor 8/13. Has not happened as of yesterday. I have checked all of the grounds, added a new ground system called the Big Three. I should not have to put all this work into a well documented issue not only in the C6 but other models.

Vehicle has open recall 09v491 for roof panel separation. The roof on the vehicle has separated and come apart in pieces leaving the front seal exposed. Gengras Chevrolet in Ct has ordered and received the replacement panel which has now been sitting at their dealership for approximately 2.5 weeks because they refuse to send it to paint until they rectify the outdated paint supply reimbursement cost with GM. In the meantime I have not had a spot for the vehicle inside and if I dont know its going to rain or dont get the car inside somewhere in time the water leaks down the windshield post and into the body control module. Currently the car drains the battery, gauges intermittently do not work as well as the power windows, starter button etc. from a recent pop up storm. Ive been back and forth with the dealer and spoke to a GM rep, niehter of which have proven useful in the situation. I just keep getting pushed off and told that I have to wait for them to figure it out with GM, even though it could potentially take 2 or more weeks to paint the top once the body shop actually gets it. This whole process has started approximately August 1st.

VEHICLE STARTS BUT WILL NOT SHIFT OUT OF PARK WITH FOOT ON BRAKE. EVENTUALLY AFTER REPEATED ATTEMPTS OR LEAVING VEHICLE FOR A LITTLE WHILE, RE-TRY AND ISSUE GOES AWAY. ISSUE HAPPENS RANDOMLY AND CANNOT BE REPLICATED EASILY.

This lead to an injury accident which totaled the car. I have documentation stating that the recall was fixed, but after I moved to Germany with the Army, the recall regularly activated the active handling when not needed (e.g parking) but then when we started slipping, the active handling did not engage and we crashed, totaling the car. The airbags did not engage even though the car played pinball on both sides of the autobahn. If we were going any faster, we would have died.

THE AIRBAG LIGHT KEEPS ILLUMINATING FOR NO REASON. FROM WHAT I READ, THE AIRBAG SYSTEM WILL NOT OPERATE WHEN THE RED INDICATOR LIGHT ON THE DASHBOARD LITE

My car has been broken for over a year now. It has been to the dealership for the main engine wiring harness part number 19115750 which is unique to the 2005 and 2006 corvette. The failure causes several different problem. It keeps the TCM from which is the traction control module which adjust speed and traction to the wheels which is design to help drivers keep their cars under control. Without this system the car will loose traction and can cause it to go off the road. The second issue with the harness is it can put the car limp mode which restricts the speed to under 40mph which if you are driving and trying to excel into traffic this system will come in without notice and put you into a situation where if you are trying to merge or just go when the light changes it will only go like 5 mph causes the cars behind you to run into the rear of your vehicle and when if fail and you are pulling into traffic it causes your car to be in a direct line of impact with oncoming vehicle. The engine harness also provides power to the transmission via the ECM which keeps it from providing enough power to run the transmission control computer. This will make your car not go into gear or make it go completely out so without a transmission your car won’t move at all. This happens without notice. Now GM doesn’t make a replacement harness anymore making your vehicle unusable. GM also wants between 7k and 10k to make a harness for the vehicle. This doesn’t include installation. This makes the owners like myself have to seek other means to repair the vehicle. Like having a custom harness made for vehicle. Since GM only made this harness for 2 years it has been impossible for me to get my vehicle repaired at any cost. Making owner to make decisions that are unfair to owners. Like sell the car for scrap Paid the expensive repair which is like half the value of the car. Trade the car and lose thousands of dollars if you can find a dealership willing to take it

I left my driveway and got two miles up the road and with no warning lights or anything dashboard went dark and suddenly car put itself into assesory mode and car just stopped while driving. I was probably going 15 mph and luckily no one was behind me. The dash said to "shift into park" so I did then I started by pushing start button and it started right up with no problem. I can't get anyone to service vehicle because they said it is not reading any code from check engine light ect. So all I can do is hope it doesn't do this again. Scary.

I bought this2005 corvette 3months and when i park it in the garage it fills up with gas fumes and could spark a fire.I have investigated this problem and its related to the gas tanks plastic parts.

Fuel tank has a leak and the unburned fuel sits on top of the tank. The whole inside of the cabin smells strong of fuel and goes away about five minutes after driving. The unburned fuel and the smell only happen when the vehicle is parked and turned off. I have called the dealership about this issue multiple times and am still waiting for a call back to see what can be done. It has been about one month and still haven't received anything back. With the unburned fuel sitting on the top of the tank, while driving it could spill onto the exhaust pipes and cause a fire. There has been no warning lights of any kind that would have told me that something was wrong.

WHILE DRIVING THE CAR IN THE BUSY ROAD ON JULY 5, 2005 THE DIC SHOWED SERVICE ACTIVE HANDLING SYSTEM, AND THE ENGINE ABS AND TCS WARNING LIGHTED UP IN THE DASHBOARD, SUDDENLY THE CAR SLOWED DOWN AND HAVE DIFFICULTY ACCELERATING.

TL* THE CONTACT OWNS A 2005 CHEVROLET CORVETTE. WHILE REVERSING THE VEHICLE AT 5 MPH, THE SERVICE ACTIVE HANDLING SENSOR AND TRACTION CONTROL WARNING INDICATORS ILLUMINATED. IT WAS DIAGNOSED THAT THE BODY CONTROL MODULE FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED, BUT THE FAILURE RECURRED TWO WEEKS LATER. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 10V172000 (STEERING). THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 28,757.

COLUMN LOCK FAILURE (4 TIMES) . CONVERTIBLE TOP 5+ TIMES RIB IN TOP BROKEN,TOP WILL NOT RAISE OR LOWER OR WILL MOVE AND STOP. PLASTIC INTERIOR PARTS DRY UP AND BREAK VISOR.ALL BEFORE 50K MILES.CAR IS IN THE DEALER SHOP (30+ DAYS AT THIS TIME)

AC INOP SPEED ONLY ONE SETTING. DEALER PULLED DASH AND REPLACE BAD MODE VALVE ACTUATOR AND CONTROLLER. 10 MONTHS LATER 08/11 SAME ISSUE AC ONLY ONE SPEED AND CAUSING MOISTURE TO APPEAR ON FRONT WINDSHIELD. DEALER REMOVE DASH AND REPLACED 2 ACTUATORS AND VALVE. 7 MONTHS LATER 03/12 SAME ISSUE AGAIN DEALER PULLED DASH AND REPLACED MODE VALVE AND ACTUATORS AGAIN. 4 MONTHS LATER 07/12 SAME ISSUE ONLY ONE SPEED AND NO AUTO SPEED . PULLED DASH AGAIN AND REPLACED THE ENTIRE HVAC CASE SAYING IT WAS WARPED. 3 MONTHS LATER 10/12 SAME ISSUE PULLED DASH AND MODE VALVE AND ACTUATORS AND VALVES..06/13 SAME ISSUE GOING INTO DEALER SERVICE AGAIN. AL THIS AND HAVE ONLY DRIVEN CAR FOR 10,000 MILES. SO FAR EVERYTHING HAS BEEN COVERED BY WARRANTIES AND ALWAYS GET A LOANER BUT I WANT TO DRIVE MY CORVETTE. *TR

I purchased my 2005 Corvette C6 from a used car dealership on 4/30/2023. The car was fine for the first week. The second week I began getting a lot of error codes specifically: Service Active Handling System Service Traction Control Service ABS Shocks Inoperative Service Fuel System. At times it would go into limp mode. I would find a safe place to pull off. I would shut the car off and it would not restart. I would check the relays under the hood and the passenger floorboard. Eventually it would restart and drive again until the next time. I have replaced the following components: Battery cables with factory replacement New Battery, twice New high output alternator and a new belt. These items solved the many codes. Now I get Service Traction System, and the traction control shuts off. When this happened last, I got a P0101 MAF sensor error. Replaced the MAF Sensor 8/13. Has not happened as of yesterday. I have checked all of the grounds, added a new ground system called the Big Three. I should not have to put all this work into a well documented issue not only in the C6 but other models.

WHILE DRIVING 70+MPH ON AN INTERSTATE, "REDUCED POWER MODE" AND "SERVICE ACTIVE HANDLING" WARNINGS ILLUMINATED ON THE DIC AONG WITH THE CHECK ENGINE LIGHT. THE VEHICLE THEN COMPLETELY SHUT OFF MAKING IT EXTREMELY DANGEROUS TO GET SAFELY OUT OF THE PATHS OF OTHER VEHICLES. THIS HAS HAPPENED TO THE VEHICLE ABOUT 8 TIMES NOW IN VARYING CIRCUMSTANCES, MOSTLY WHILE IN MOTION. ERROR CODES TAKEN FROM HANDHELD PROGRAMMER INCLUDE: P1516, P2101, P2135

AUTOMATIC TRANSMISSION SHIFT HANDLE LOCKS IN PARK AND YOU CAN NOT SHIFT INTO GEAR. THIS IS A KNOWN ISSUE AND GM EVEN NOTES HOW TO OVER-RIDE THE PROBLEM IN THE OWNERS MANUAL (SEE PAGE 2-31), WHEN IT HAPPENS. SINCE THIS HAPPENS SO OFTEN, AND TO SO MANY OWNERS (SEE INTERNET COMMENTS ON PROBLEM), A PERMANENT FIX SHOULD BE DONE AND COVERED BY THE MANUFACTURER. IN AN EMERGENCY SITUATION YOU MAY NOT HAVE TIME TO PLAY WITH THE SHIFTER AND THIS CAN LEAD TO AN ACCIDENT OR PERSONAL INJURY. WHILE GM DOES NOTE TO CONTACT A DEALER ABOUT THIS PROBLEM IN THE OWNERS MANUAL, NO RECALLS SEEM TO HAVE BEEN MADE? *JS

TL* THE CONTACT OWNS A 2005 CHEVROLET CORVETTE. THE CONTACT STATED THAT THE GEAR LEVER FAILED TO SHIFT OUT OF PARK. THE CONTACT MENTIONED THAT HAD TO ATTEMPT TO SHIFT GEAR SEVERAL TIMES BEFORE IT CHANGE. THE FAILURE OCCURRED WHENEVER THE VEHICLE WAS IN OPERATION. THE VEHICLE HAD NOT BEEN DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE DEFECT. THE APPROXIMATE FAILURE MILEAGE WAS 19,000.

The active handling applies itself with normal non aggressive driving. When activated the brakes apply and lock up, this has happened in low speed turns at intersections and even when driving straight. I have had the vehicle to the dealership to resolve as this is a major safety concern leaving the car locked up in the middle of an intersection. They stated it was the sensor behind the steering wheel and they fixed it but the problem still persists. Secondly the driver seat has begun moving on its own and inching me closer to the steering wheel with no interference with the button while driving. I have since disconnected the seat fuse to prevent collision from improper driver positioning.

POWER STEERING HOSE LEAK, HAD DEALER REMOVE, REPLACE. I WAS COVERED UNDER WARRANTY PURCHASE, ALSO TAIL LIGHTS AND HEADLIGHTS INOPERABLE, HAD DEALER PERFORM SAFETY INSPECTION. ITEMS CORRECTED. RECENT PURCHASE JAN. 2016 USED.

TIRE PRESSURE SENSORS FAIL WITHOUT INDICATION. THE SENSOR REGISTERS PRESSURE WHEN IT IS ACTUALLY ZERO. WITH RUN FLAT TIRES THIS CAUSES AN UNSAFE CONDITION. *TR

THERE IS A DANGEROUS PROBLEM WITH MY CORVETTE THAT I BELIEVE IS TIED TO FAULTS IN THE TIRE PRESSURE MONITORING SYSTEM. I WAS DRIVING ON A FREEWAY FOLLOWING A LEFT CURVE WHEN I FELT THE BRAKES GRAB. I SAW "ACTIVE HANDLING" DISPLAYED; HOWEVER, THERE WAS NO REASON FOR ACTIVE HANDLING TO OCCUR (ROADWAY WAS DRY, WAS DRIVING AT POSTED SPEED LIMIT, WAS NOT MAKING A SUDDEN TURNING MANEUVER). LATER I SAW THAT THE CAR WAS DISPLAYING A FRONT RIGHT TIRE PRESSURE OF 0 PSI, BUT NO OTHER WARNINGS OCCURRED (TYPICALLY, A YELLOW WARNING LIGHT GOES ON AN CAR DISPLAYS A LOW TIRE PRESSURE OR RIGHT FRONT TIRE FLAT WARNING WHEN THIS OCCURS). I'VE HAD ONGOING PROBLEMS WITH THE TIRE PRESSURE MONITORING SYSTEM AND CHEVY HAS ATTEMPTED REPAIR ONCE. USUALLY ONE OF THE FRONT TIRES WILL READ ZERO PSI AND THE AFOREMENTIONED WARNINGS WILL APPEAR, AND THE CAR'S ACTIVE HANDLING SYSTEM WILL ENGAGE MORE EASILY, THEN A FEW MINUTES LATER, THE CAR WILL DISPLAY NORMAL TIRE PRESSURES AGAIN. IN THE INCIDENT I'M DESCRIBING HERE, THERE WAS NO WARNING THAT THE TIRE PRESSURE WAS BEING READ AT ZERO, AND NO INDICATION THAT ACTIVE HANDLING WOULD ENGAGE SO EASILY. THIS IS A DEFINITE SAFETY HAZARD THAT COULD RESULT IN LOSS OF CONTROL OR A CRASH. I HAVE AN APPOINTMENT TO GET THE CAR SERVICED IN TWO DAYS. *TR

TL*THE CONTACT OWNS A 2005 CHEVROLET CORVETTE. WHENEVER THERE IS ANY TORQUE PRESENT, THE CONTACT HEARS A CRUNCHING AND POPPING NOISE COMING FROM THE ROOF PANEL. THE FAILURE OCCURS INTERMITTENTLY BECAUSE THE LAMINATED PART OF THE ROOF IS SEPARATING. THE VEHICLE HAS BEEN TO THE DEALER SIX TIMES FOR THIS FAILURE, WITH THE MOST RECENT OCCURRENCE ON JANUARY 17, 2008. THE FAILURE HAS SINCE WORSENED. THE CONTACT DOES NOT BELIEVE THAT THERE IS A REPAIR AVAILABLE FOR THIS FAILURE. THE CURRENT MILEAGE WAS 22,900 AND FAILURE MILEAGE WAS 3,000. UPDATED 05/20/08. *LJ THE SEAT BELT BUZZER WOULD GO OFF AT TIMES, THE PASSENGER SIDE DOOR MADE A POPPING NOISE WHEN IT WAS OPENED. UPDATED 05/20/08

DT: THE CONTACT OWNS A 2005 CHEVROLET CORVETTE. THE CONTACT STATED THAT THE BOLSTER IN THE VEHICLE WAS BUILT TOO HIGH AND IT WAS WEARING OUT. THE CONTACT OWNS A 2003 CORVETTE, AND THEY MODIFIED THE BOLSTER FOR HIM IN THAT CAR BY LOWERING IT. THEY CANNOT MODIFY THE BOLSTER IN THE 2005 MODEL BECAUSE OF THE AIR BAGS. THE VINYL ON THE BOLSTER IS PAPER THIN, AND WHEN HE GETS IN AND OUT OF THE VEHICLE IT IS WEARING THE VINYL OUT. THE DEALERSHIP HAS ALREADY REPLACED THE BOLSTER ONCE, AND IT NEEDED TO BE REPLACED AGAIN. THE CONTACT HAS OWNED THE VEHICLE LESS THAN SIX MONTHS. *AK