RoadVitals

2006 Chevrolet Corvette Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Data refreshed

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
5
Newest May 14, 2014
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0
4 investigations on file

Recall campaigns

5 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

ELECTRICAL SYSTEM:WIRING; EXTERIOR LIGHTING:HEADLIGHTS

May 14, 2014
103,158 units potentially affected
The defect: General Motors LLC (GM) is recalling certain model year 2005-2007 Chevrolet Corvette vehicles manufactured March 29, 2004, through June 22, 2007. In the affected vehicles, the underhood bussed electrical center (UBEC) housing can expand and cause the headlamp low beam relay control circuit wire to bend. If the wire is repeatedly bent, it may fracture causing a loss of low beam headlamp illumination.
The risk: The loss of low beam headlamp illumination will decrease the driver's visibility, as well as the vehicle's conspicuity to other motorists, increasing the risk of a crash.
The remedy: GM will notify owners, and dealers will install a jumper wire to correct this condition, free of charge. The recall began January 2, 2015. Owners may contact Chevrolet customer service at 1-800-222-1020. GM's number for this recall is 13146. Note: Model year 2008-2013 Chevrolet Corvettes will be covered under customer satisfaction program number 14203 for the same issue.
General Motors LLCManufacturer number 13146View on NHTSA.gov

STEERING:COLUMN

Apr 26, 2010
40,028 units potentially affected
The defect: GM IS RECALLING CERTAIN MODEL YEAR 2005 AND 2006 CHEVROLET CORVETTE PASSENGER CARS MANUFACTURED BETWEEN MARCH 2004 AND JANUARY 2006 EQUIPPED WITH A TILT AND TELESCOPING STEERING COLUMN (RPO N37). IN RARE CASES, REPEATED MOVEMENT OF THE STEERING COLUMN MAY CAUSE A SIGNAL INTERRUPTION WITHIN THE COLUMN. IF THIS OCCURS, THE MESSAGE, "SERVICE ACTIVE HANDLING SYSTEM" WILL APPEAR IN THE DRIVER INFORMATION CENTER, AND ONE OR MORE OF THE BRAKES MAY APPLY, POSSIBLY CAUSING THE VEHICLE TO PULL TO THE RIGHT OR LEFT.
The risk: IF THE DRIVER DOES NOT RESPOND TO THE CHANGE IN VEHICLE MOVEMENT, A CRASH COULD OCCUR.
The remedy: GM WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 30, 2010. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 AND GMC AT 1-866-996-9463 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.
GENERAL MOTORS CORP.View on NHTSA.gov

STRUCTURE:BODY:ROOF AND PILLARS

Dec 23, 2009
22,090 units potentially affected
The defect: GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2007 CORVETTE VEHICLES EQUIPPED WITH A REMOVABLE ROOF AND MODEL YEAR 2006 AND 2007 CORVETTE Z06 VEHICLES. THE ADHESIVE BETWEEN THE ROOF PANEL AND THE FRAME MAY SEPARATE. IF THERE IS A PARTIAL SEPARATION, THE DRIVER MAY NOTICE ONE OR MORE SYMPTOMS, SUCH AS A SNAPPING NOISE WHEN DRIVING OVER BUMPS, WIND NOISE, POOR ROOF PANEL FIT, ROOF PANEL MOVEMENT/BOUNCE WHEN A DOOR OR HATCH IS CLOSED, OR A WATER LEAK IN THE HEADLINER.
The risk: IF THERE IS A COMPLETE SEPARATION, THE ROOF PANEL MAY DETACH FROM THE VEHICLE. IF THIS WERE TO OCCUR WHILE THE VEHICLE WAS BEING DRIVEN, IT COULD STRIKE A FOLLOWING VEHICLE AND CAUSE INJURY AND/OR PROPERTY DAMAGE.
The remedy: DEALERS WILL INSTALL A NEW DESIGN ROOF PANEL FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING APRIL 2010. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438 OR AT WWW.GMOWNERCENTER.COM.
GENERAL MOTORS CORP.Manufacturer number 090230View on NHTSA.gov

STRUCTURE:BODY:ROOF AND PILLARS

May 24, 2006
30,793 units potentially affected
The defect: ON CERTAIN 2005-2006 CHEVROLET CORVETTES EQUIPPED WITH PAINTED ROOFS, THE ADHESIVE BETWEEN THE ROOF PANEL AND THE FRAME MAY SEPARATE.
The risk: IF THERE IS A COMPLETE SEPARATION, THE ROOF PANEL MAY DETACH FROM THE VEHICLE AND IT COULD STRIKE ANOTHER VEHICLE AND CAUSE INJURY AND PROPERTY DAMAGE.
The remedy: DEALERS WILL INSPECT VEHICLES FREE OF CHARGE FOR POTENTIAL ROOF PANEL-TO- FRAME SEPARATION AND ADD THE SPECIFIED ADHESIVE FOAM OR REPLACE THE ROOF WITH ONE HAVING ADHESIVE FOAM. THE RECALL BEGAN ON OCTOBER 19, 2006. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438.
GENERAL MOTORS CORP.Manufacturer number 06041View on NHTSA.gov

STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS

Oct 5, 2005
123,592 units potentially affected
The defect: CERTAIN PASSENGER VEHICLES MAY HAVE BEEN BUILT WITH A POWER STEERING HOSE THAT IS NOT TO SPECIFICATION. UNDER EXTREME STEERING MANEUVERS, SUCH AS TURNING THE STEERING WHEEL FULLY TO THE LEFT OR RIGHT WHILE BRAKING, THE HOSE MAY FRACTURE AND LEAK FLUID.
The risk: IF THIS WERE TO OCCUR, POWER STEERING ASSIST WOULD BE LOST AND INCREASED STEERING EFFORT WOULD BE REQUIRED. ON VEHICLES EQUIPPED WITH HYDRO-BOOST POWER BRAKES, IT COULD ALSO RESULT IN LOSS OF POWER BRAKE ASSIST AND INCREASED BRAKING EFFORT WOULD BE REQUIRED. IF THE POWER STEERING FLUID SPRAY WERE TO SPRAY ONTO HOT ENGINE PARTS, AN ENGINE COMPARTMENT FIRE COULD OCCUR.
The remedy: DEALERS WILL INSPECT THE POWER STEERING HOSE(S) FOR TWO SUSPECT DATE CODES AND REPLACE THEM IF REQUIRED. THE RECALL WILL BEGIN ON OCTOBER 14, 2005. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438, GMC AT 1-866-996-9463, BUICK AT 1-866-608-8080, CADILLAC AT 1-866-982-2339, ISUZU AT 1-800-255-6727, OR HUMMER AT 1-800-732-5493.
GENERAL MOTORS CORP.Manufacturer number 05086View on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Safety investigations

NHTSA inquiries naming this vehicle. An investigation is not a finding of a defect, and it is not a recall.

EA13007ClosedEngineering Analysis

Simultaneous Loss of Low-Beam Headlights

Opened Aug 23, 2013
Closed Jun 24, 2014

On May 14, 2014, General Motors (GM) submitted a Part 573 defect information report initiating NHTSA Safety Recall 14V-251 to remedy the subject vehicles.GM will remedy a defect condition in the underhood bussed electrical center (UBEC) by modifying the vehicle's electrical harnessing.GM also announced a customer satisfaction bulletin to address this issue on model year (MY) 2008-2013 Chevrolet Corvettes.Both programs will be conducted free of charge.According to GM, when the engine heats up and cools down (from normal use), the plastic material in the UBEC housing expands at a different rate than an electrical conductor routed within it.The difference in expansion rates results in bending of the conductor, a control circuit for the low beam headlights.After multiple thermal cycles, often taking several years of use, the conductor fractures resulting in an open circuit.When this occurs the low-beam headlights will not illuminate.After the engine is turned off and the UBEC cools, the conductor may temporarily reconnect and restore low-beam function, although subsequent failures will occur.This condition does not affect high-beam headlights, marker lamps, turn signals or fog lamps.Simultaneous loss of low-beam headlights could reduce the driver's visibility, increasing the risk of a crash. The ODI report counts noted above, involving the loss of low beam headlights, represents those received at the time of GM's recall filing; however NHTSA has since received additional complaints.GM submitted similar complaints in response to the agency's information request.Among the complaints reported to NHTSA, five alleged minor crashes in which the vehicle ran off the road or into roadside objects due to the sudden loss of headlights.Two of these complaints alleged minor injuries and three alleged property damage.Several other reports to NHTSA alleged close calls due to the loss of lighting.GM states that it has received no reports of crashes, injuries or fatalities as a result of this condition. GM's recall action appears to adequately address the safety risks in the subject vehicles of concern to ODI.Accordingly, the investigation is closed.In addition to recalling the subject vehicles, GM is covering MY 2008-2013 Corvettes, which contain essentially the same UBEC, under a customer satisfaction campaign.ODI notes that these vehicles exhibit a lower likelihood of failure due to their comparatively shorter service life. The VOQs cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10400308, 10415603, 10415867, 10416531, 10421639, 10424391, 10424543, 10445971, 10451733, 10454919, 10460674, 10460750, 10463546, 10466342, 10466857, 10468128, 10469057, 10470616, 10471595, 10474350, 10474368, 10475257, 10486597, 10491670, 10496592, 10496788, 10498100, 10502059, 10505606, 10508507, 10510052, 10511467, 10511517, 10511576, 10511696, 10511699, 10511789, 10511837, 10511994, 10512072, 10512093, 10512154, 10512292, 10512341, 10512856, 10513422, 10514576, 10514802, 10514978, 10515162, 10515311, 10515821, 10519426, 10519879, 10520155, 10521036, 10521585, 10522260, 10523059, 10523064, 10523190, 10525646, 10531602, 10531631, 10532221, 10532439, 10533227, 10533251, 10533339, 10536835, 10537561, 10537612, 10538184, 10541749, 10542468, 10542540, 10542576, 10542708, 10542726, 10543187, 10543970, 10544083, 10544810, 10545441, 10545516, 10547343, 10547561, 10547600, 10548492, 10548588, 10548687, 10548982, 10549272, 10549487, 10550079, 10550260, 10551233, 10551867, 10551926, 10551978, 10552019, 10553258, 10554456, 10554573, 10556002, 10556433, 10556844, 10556984, 1

EXTERIOR LIGHTINGLed to recall 14V251000
PE13013ClosedPreliminary Evaluation

Loss of Low Beam Headlights

Opened May 6, 2013
Closed Aug 26, 2013

The Office of Defects Investigation (ODI) opened this investigation based on 30 reports from consumers alleging that, after driving for a short time (5 to 30 minutes), both low beam headlights stopped working simultaneously and without warning. The low beam headlights remained inoperative for the remainder of the drive cycle, however no other lighting is affected.General Motors (GM) provided information in response to ODI's information request letter explaining that the loss of headlights is caused by a fractured low beam circuit wire in the underhood bussed electrical center (UBEC), a device that is similar to a fuse box. The UBEC is located in a high heat area near the engine, and the low beam circuit wire routing within the UBEC makes it susceptible to cyclical stress caused by thermal expansion.The investigation covers model years 2005-2007 Corvettes however ODI also has received four VOQs alleging the same condition in model year 2008 Corvettes. ODI is upgrading the investigation to an Engineering Analysis to further examine the consequences, frequency and scope of this problem. The ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers.For MY 2005-2007: 10400308, 10415603, 10415867, 10416531, 10421639, 10424391, 10424543, 10445971, 10451733, 10454919, 10460674, 10460750, 10463546, 10466342, 10466857, 10468128, 10469057, 10470616, 10471595, 10474350, 10474368, 10475257, 10486597, 10491670, 10496592, 10496788, 10498100, 10502059, 10505606, 10508507, 10510052, 10511467, 10511517, 10511576, 10511696, 10511699, 10511789, 10511837, 10511994, 10512072, 10512093, 10512154, 10512292, 10512341, 10513422, 10514802, 10514978, 10515162, 10515311, 10515821, 10519426, 10519879, 10520155, 10521036, 10521585, 10522260, 10523064, 10523190, 10525646, 10531602, 10531631, 10532439, 10533227, 10533251, 10533339For MY 2008: 10512856, 10514576, 10523059, 10532221

EXTERIOR LIGHTING
EA09002ClosedEngineering Analysis

Electronic Stability Control

Opened Jan 14, 2009
Closed May 11, 2010

On April 26, 2010, at NHTSA's request following this investigation, General Motors submitted a Defect Information Report to NHTSA to correct a defect associated with the Vehicle Stability Control (VSC) system in approximately 40,000 Model Year (MY) 2005 and 2006 Chevrolet Corvette vehicles (NHTSA Recall No. 10V-172).According to the report, these vehicles may have a problem with the Steering Wheel Position Sensor (SWPS) connector created by a fretting condition in the connector (small movement of the pins back and forth creating a residue build up) which could change the electrical resistance and corrupt the information signal to the VSC computer.The VSC system uses the information from the SWPS to calculate the driver's intended vehicle direction; this information is cross referenced to sensors that tell the system which direction the vehicle is actually going and the system will, if it determines a variance indicating the vehicle is in a over-steer or under-steer condition, reduce throttle control and apply braking to make a correction in vehicle direction towards what the system believes is the driver's intended path.GM dealers will inspect the SWPS connector of recalled vehicles and, if necessary, install a terminal position assurance clip to the connector.GM has advised NHTSA that its position is that the inappropriate activations of the VSC system do not present an unreasonable risk to safety because GM believes that the activations are low in occurrence, a rare set of conditions would need to be present, the driver has the ability to maintain direction control if the alleged condition were to occur, and that there are no reports of injuries.NHTSA does not agree.Based on interviews with complainants and testing performed at the NHTSA Vehicle Research and Testing Center in East Liberty, Ohio, ODI believes that the majority of the unwarranted activations of the VSC system occur when turning, in such scenarios as travelling highway entrance or exit ramps or in street traffic conditions.Complainants report the effect produced by the malfunction of the VSC system is sudden unexpected braking and in some cases a sudden unexpected change in vehicle direction which some complainants indicate was sufficient to cause a movement into an adjoining lane of traffic or in some cases into curbing or stationary objects.During the VSC event the brake lights of the Corvette are not illuminated, depriving trailing traffic from indication that braking is occurring and some complainants indicate the braking effect can be severe and last up to 10 seconds in length.Based on available information ODI counts four crashes due to a malfunction of the VSC system; GM is counting one crash due to the problem.In these circumstances NHTSA believes the defect presents an unreasonable risk to motor vehicle safety, and so advised GM when requesting this recall.This investigation is closed based on GM's recall.

ELECTRONIC STABILITY CONTROLLed to recall 10V172000
PE08056ClosedPreliminary Evaluation

ELECTRONIC STABILITY CONTROL MALFUNCTION

Opened Sep 17, 2008
Closed Jan 14, 2009

ON SEPTEMBER 17, 2008, ODI OPENED PRELIMINARY EVALUATION PE08-056 TO INVESTIGATE ALLEGATIONS OF INAPPROPRIATE ACTIVATION OF THE ELECTRONIC STABILITY CONTROL (ESC) SYSTEM IN MODEL YEAR (MY) 2005 AND 2006 CHEVROLET CORVETTE VEHICLES.SOME REPORTS RECEIVED BY ODI AND SOME REPORTS TO GENERAL MOTORS (GM) CONTAINED IN GM'S RESPONSE TO PE08-056 ALLEGE THAT THE ESC SYSTEM MALFUNCTIONED CAUSING A SUDDEN AND INAPPROPRIATE BRAKING ACTION WITHOUT ILLUMINATION OF THE BRAKE LIGHTS AND CAUSING THE VEHICLE TO SWERVE LEFT OR RIGHT UNEXPECTEDLY. GM ISSUED A TECHNICAL SERVICE BULLETIN IN JANUARY 2006, LATER REVISED IN OCTOBER 2007 (BULLETIN NO. 06-02-35-002B) CONCERNING ESC PROBLEMS IN MY 2005 AND 2006 CHEVROLET CORVETTE VEHICLES WITH THE TELESCOPING STEERING WHEEL OPTION.THE BULLETIN WAS INTENDED TO CORRECT A FRETTING CORROSION PROBLEM WITH THE STEERING WHEEL POSITION SENSOR CONNECTOR C202. AN ENGINEERING ANALYSIS HAS BEEN OPENED (EA09-002) TO CONTINUE TO ASSES THE SCOPE, FREQUENCY, AND SAFETY-RELATED CONSEQUENCES OF THE ALLEGED DEFECT.

ELECTRONIC STABILITY CONTROL

Elsewhere on this vehicle

Data sources

Data on this page last refreshed .