2017 Chevrolet Silverado 3500 Problems

The contact owns a 2017 Chevrolet Silverado 3500. The contact stated that while driving at various speeds, the vehicle failed to upshift while depressing the accelerator pedal. The check engine warning light was illuminated. The vehicle was taken to a local independent mechanic and was diagnosed with a stuck torque converter. The contact stated that DTC code: P0741 was retrieved. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 58,000.

The contact owns a 2017 Chevrolet Silverado 3500. The contact received a recall notification for NHTSA Campaign Number: 21V496000 (Equipment) however, the dealer informed the contact that the parts for the recall repair were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue and confirmed that the part was not yet available. The contact had not experienced a failure. VIN tool confirms parts are not available.

TL* THE CONTACT OWNS A 2017 CHEVROLET SILVERADO 3500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V088000 (FUEL SYSTEM, GASOLINE); HOWEVER, THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT CALLED THE MANUFACTURER AND THEY DISCONNECTED THE CALL. THE DEALER WAS NOT CONTACTED. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

RECALL WAS ANNOUNCED FEB 7, 2019 MY COMPLAINT IS WHY IS IT TAKING SO LONG TO OBTAIN PARTS AND GET THE VEHICLE REPIRED IT HAS BEEN THREE MONTHS

The contact owns a 2017 Chevrolet Silverado 3500. The contact stated that the vehicle was unable to start. The contact replaced the battery and starter; however, the failure recurred. Upon inspection, the contact noticed that the fuse panel had melted. The vehicle was towed to the dealer where it was determined that the main wiring harness and the fuse panel needed to be replaced. The vehicle was not repaired and remained at the dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 22,000.

THE MYLINK BACKUP CAMERA DOES NOT ALLOW DIMMING AT NIGHT WHEN BACKING THE VEHICLE CAUSING THE MYLINK BACKUP CAMERA SCREEN IN THE DASH TO GO FULL BRIGHTNESS, THUS BLINDING THE DRIVER FROM SEEING THE PASSENGER MIRROR. THIS IS A SAFETY HAZARD THAT CAN CAUSE AN ACCIDENT WHEN BACKING THE VEHICLE AT NIGHT.

The contact owns a 2017 Chevrolet Silverado 3500. The contact received notification of NHTSA Campaign Number: 21V496000 (Equipment) however, the part to do the recall repair was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer and another dealer, McCarthy Chevrolet (675 N Rawhide, Olathe, KS 66061) were made aware of the recall but informed the contact that parts were not yet available. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

THE RETURN LINE FROM THE TRANSMISSION COOLER IS RUBBING ON THE BUMPER MOUNT BRACKET. MY VEHICLE HAS JUST OVER 9000 MILES ON IT AND THE COVER AROUND THE LINE IS ALREADY WORN THROUGH. THE WAY THE LINE IS MOUNTED OFFERS NO FLEXIBILITY TO PUSH IT AWAY FROM THE BUMPER BRACKET. THIS WILL EVENTUALLY LEAD TO A FAILURE OF THE RETURN LINE ON THE TRANSMISSION COOLER. I WAS INFORMED OF THIS ISSUE BY A POST ON A PUBLIC FORUM. THE PERSON THAT POSTED THIS ISSUE HAD A FAILURE OF THE RETURN LINE IN THE SAME SPOT DUE TO THE SAME ISSUE.

TL* THE CONTACT OWNS A 2017 CHEVROLET SILVERADO 3500 EQUIPPED WITH GOODYEAR WRANGLER SR-A TIRES, SIZE: 275/55/R20. WHILE DRIVING 50 MPH ON A MOUNTAINOUS ROAD, THE FRONT PASSENGER SIDE TIRE BLEW OUT. THE CONTACT CHANGED THE TIRE WITH A SPARE AND INTENDED TO REPLACE THE REMAINING TIRES WITH ANOTHER BRAND. THE MANUFACTURER WAS NOT CONTACTED. THE VIN WAS UNKNOWN. THE VEHICLE AND TIRE FAILURE MILEAGE WAS 24,469.

The complaint is against Reading Truck Body, LLC regarding safety concerns left unresolved and property damage incurred because of the recall remedy work (NHTSA Campaign Number 18E-021) performed on my 2017 Silverado 3500HD Crew Cab service truck by Reading Truck Body, LLC. In May 2020, I was notified by Reading Truck Body, LLC of a safety recall specific to the aluminum service body on my truck. Following the initial remedy “patch” work done by the company, I was shocked to discover damages to the rear crossmember and compromising cracks in the welding of the body, as well as to the integrity and functionality of the wiring harnesses on my vehicle. Despite assurances that these damages would be addressed, I have been met with delays, unresponsiveness, and ultimately a subpar replacement body that does not meet the quality and craftsmanship of the original. The replacement body not only fails to match the size and finish of the original, but also poses serious safety risks due to missing bolts, faulty wiring harnesses, and overall poor construction. Despite my repeated attempts to seek resolution through the company’s Recall and Warranty departments, I have been met with dismissive treatment, unfounded accusations, and a refusal to address the issues at hand. This has not only caused financial loss and property damage but has also taken a toll on my emotional well-being and business operations. As a concerned customer, I am requesting your support to hold Reading Truck Body, LLC accountable for their actions in this complaint and fully remedy the recall. To do so, I request they replace the service body with one of equal quality, size, and finish as my original. Proper powder coating and meticulous craftsmanship are essential to restoring the value and integrity of my vehicle. I urge you to help rectify these issues promptly and help me ensure Reading Truck Body, LLC addresses the safety concerns outlined in my complaint. Supporting documentation attached

The contact owns a 2017 Chevrolet Silverado 3500. The contact stated that while driving at various speeds, the vehicle failed to upshift while depressing the accelerator pedal. The check engine warning light was illuminated. The vehicle was taken to a local independent mechanic and was diagnosed with a stuck torque converter. The contact stated that DTC code: P0741 was retrieved. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 58,000.

Since the purchase of the truck the vehicle does emergency breaking at different times from what seems to be faults sensor input. #1 on freeway onramp specialty circular 2 lane, if on the inside lane the truck will alarm and drop the throttle out. This also happens some time at the 3/4 point of the on ramp when cars on the freeway are perpendicular in front of the vehicle. # 2 the same alarm and throttle dropout happen on the freeway randomly and on two lane roads when vehicle are approaching on a 2 line road. I don’t know if break lights are activated, but I have had people honk at me for the deceleration.