RoadVitals

2002 Ford Taurus Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Data refreshed

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
4
Newest Apr 1, 2016
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0
4 investigations on file

Recall campaigns

4 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:PADS

Apr 1, 2016
49,635 units potentially affected
The defect: Bosch Brake Components LLC (Bosch) is recalling certain aftermarket replacement front brake pads, models Bosch QuietCast BC598 and BP765, Bosch Blue BE598 and BE598H, Prostop PD598 and PD765M, Duralast Gold DG598, Duralast MKD598, Stop Master ST598, UltraStop ULT598, UltraLife MX598 and MX765, BrakeBest MKD765, and Prostop Platinum PGD598. These brake pads, manufactured October 1, 2014, to October 31, 2015 are intended for use on 2001-2007 Ford Taurus, 2001-2005 Mercury Sable, 1995-1999 Ford Taurus SHO, 1995-2002 Lincoln Continental, and 1993-1998 Lincoln Mark VIII vehicles. The brake pad shim may shift out of position causing the shim to contact the brake disc resulting in damage to the disc.
The risk: A damaged or broken brake disc may reduce a vehicle's braking power, increasing the risk of a crash.
The remedy: Bosch will instruct the owners how to have the affected brake pads replaced, free of charge. The recall began on May 26, 2016. Owners may contact Bosch customer service at 1-888-715-3616.
Robert Bosch LLCView on NHTSA.gov

EXTERIOR LIGHTING:BRAKE LIGHTS:SWITCH

Mar 2, 2004
938,789 units potentially affected
The defect: CERTAIN PASSENGER VEHICLES ARE BEING RECALLED TO CORRECT A PROBLEM WITH A MALFUNCTIONING STOP LAMP SWITCH AND/OR ASSOCIATED WIRING. THIS MALFUNCTIONING COULD RENDER THE STOP LAMPS INOPERABLE OR CAUSE THEM TO STAY ON ALL THE TIME. THIS COULD CAUSE CONFUSION TO A FOLLOWING DRIVER, WHICH COULD LEAD TO A CRASH.
The risk: IN ADDITION, IF THE SWITCH AND/OR ASSOCIATED WIRING FAIL IN THE OPEN POSITION, THE BRAKE LIGHTS WILL NOT ACTUATE AND THE DRIVER WILL NOT BE ABLE TO SHIFT THE VEHICLE OUT OF "PARK" IF THEY FAIL IN THE CLOSED POSITION, THE BRAKE LIGHTS WILL REMAIN ON, WHICH WILL NOT ALLOW THE SPEED CONTROL TO BE ACTIVATED. THIS COULD ALSO CAUSE THE BATTERY TO DISCHARGE.
The remedy: DEALERS WILL REMOVE THE STOP LAMP SWITCH AND ASSOCIATED WIRING ASSEMBLY AND INSTALL A NEWLY DESIGNED STOP LAMP SWITCH AND WIRE ASSEMBLY. OWNER NOTIFICATION IS EXPECTED TO BEGIN ON APRIL 5, 2004. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.
FORD MOTOR COMPANYManufacturer number 04S12View on NHTSA.gov

VISIBILITY:WINDSHIELD

Mar 10, 2003
67,894 units potentially affected
The defect: CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, "WINDSHIELD MOUNTING." THE WINDSHIELDS MAY POTENTIALLY EXHIBIT INCREASED WIND NOISE, WATER LEAKAGE, AND SQUEAKS AND RATTLES.
The risk: POTENTIAL LOSS OF WINDSHIELD RETENTION MAY ALSO REDUCE OCCUPANT PROTECTION IN THE EVENT OF A CRASH.
The remedy: DEALERS WILL REPLACE THESE WINDSHIELDS. OWNER NOTIFICATION BEGAN ON MARCH 31, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD/MERCURY AT 1-800-392-3673.
FORD MOTOR COMPANYManufacturer number 03C03View on NHTSA.gov

SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES

Oct 2, 2002
369,614 units potentially affected
The defect: CERTAIN PASSENGER VEHICLES EQUIPPED WITH ADJUSTABLE PADELS ARE BEING RECALLED IN ORDER TO ADJUST THE BRAKE AND ACCELERATOR PEDALS TO A MINIMUM OF 50 MM OF LATERAL SEPARATION. SIMULTANEOUS APPLICATION OF BOTH THE BRAKE AND ACCELERATOR PEDALS COULD RESULT IN AN INCREASE IN ENGINE RPM.
The risk: THIS COULD RESULT IN A CUSTOMER EXPERIENCING AN "UNINTENDED VEHICLE SPEED INCREASE" OR A PERCEIVED "UNABLE TO STOP" CONDITION.
The remedy: OWNERS WILL BE INSTRUCTED AS TO THE PROPER WAY TO SET THE POSITION OF THE PEDALS AND TO TAKE THEIR VEHICLES TO A DEALER TO HAVE THE SPACING BETWEEN THE BRAKE AND ACCELERATOR PEDALS MEASURED. IF THE SPACING IS FOUND TO BE LESS THAN 50 MM, THE DEALER WILL ADJUST THE PEDALS TO INCREASE THE DISTANCE BETWEEN THEM TO GREATER THAN 50 MM. OWNER NOTIFICATION BEGAN OCTOBER 28, 2002. OWNERS WHO DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.
FORD MOTOR COMPANYManufacturer number 02S40View on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Safety investigations

NHTSA inquiries naming this vehicle. An investigation is not a finding of a defect, and it is not a recall.

PE12033ClosedPreliminary Evaluation

Speed control cable damage

Opened Oct 24, 2012
Closed Jun 26, 2013

On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at NHTSA's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.

VEHICLE SPEED CONTROL:CABLES
EA08018ClosedEngineering Analysis

Front Suspension Coil Spring Fracture

Opened Aug 28, 2008
Closed Jun 30, 2011

To date, ODI is aware of 2,401 non-duplicative complaints related to the alleged defect. In addition, ODI is aware of 1,411 subject vehicles with one or more warranty claims related to the alleged defect. In total, ODI is aware of 3,645 unique subject vehicles that have experienced one or more front suspension coil spring fractures. ODI is also aware of four minor crashes related to the alleged defect resulting in one minor injury.With greater than eight years of exposure, a large subject vehicle population and approximately 2,052 reported front tire punctures caused by fractured coil springs (at all speeds), there have been no reported severe crashes, deaths or injuries related to the alleged defect. The real world consequences of these defective coil springs have been a small number of minor control problems that resulted in minor damage; suggesting that the effect of the defect on vehicle control is minor.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted. Accordingly, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency will continue to monitor this issue and will take further action if warranted by the circumstances. See the EA08-018 Engineering Analysis Closing Report for more details.

SUSPENSION:FRONT:SPRINGS:COIL SPRINGS
RP03001ClosedRecall Process

BRAKE/ACCELERATOR PEDAL APPLICATION

Opened Oct 31, 2003
Closed Mar 23, 2004

MS. RODMAN REPORTED THAT AFTER HER VEHICLE WAS INSPECTED FOR THE RECALL, HER MOTHER EXPERIENCED A SUDDEN ACCELERATION AND CRASHED THE SABLE INTO A LIGHT POLE.PREVIOUSLY NHTSA HAD CONDUCTED AN INVESTIGATION FOR THIS ISSUE (PE02-035) THAT RESULTED IN THE RECALL (02V-266) OF 369,000 MY 2000-2002 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE BRAKE AND ACCELERATOR PEDALS TO INSURE THAT THE SEPARATION BETWEEN THE PEDALS WAS AT LEAST 50MM..A REVIEW OF ODI'S DATABASE FOR COMPLAINTS REGARDING RECALL 02V-266 DID NOT IDENTIFY ANY RECALL REMEDY COMPLAINTS OTHER THAN THE PETITIONER'S.MS. RODMAN?S VEHICLE WAS INSPECTED BY ODI USING FORD?S SPECIAL TOOL AND HER VEHICLE WAS FOUND TO EXCEED 50MM.ALSO, THE LATERAL MOVEMENT OF THE PEDALS WAS FOUND NOT TO BE EXCESSIVE RELATIVE TO OTHER COMPARABLE TAURUS AND SABLE VEHICLES.THEREFORE, IT IS UNLIKELY THAT NHTSA WOULD ISSUE AN ORDER REQUIRING FORD TO PROVIDE A DIFFERENT REMEDY FOR THIS DEFECT.IN VIEW OF THE NEED TO ALLOCATE AND PRIORITIZE NHTSA?S LIMITED RESOURCES TO BEST ACCOMPLISH THE AGENCY?S SAFETY MISSION, THE PETITION IS DENIED.FOR ADDITIONAL INFORMATION CONCERNING THIS ANALYSIS, PLEASE REFER TO THE FEDERAL REGISTER NOTICE DATED MARCH 23, 2004 (VOL 69, NO 56, PAGES 13619-13620).

SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES
RQ03008ClosedRecall Query

BRAKE LIGHT SWITCH FAILURE

Opened Oct 23, 2003
Closed Mar 5, 2004

FORD CONDUCTED A RECALL IN MARCH, 2001 TO CORRECT A DEFECT AFFECTING THE BRAKE LIGHT SWITCH IN MY 2000 THROUGH EARLY-2001 TAURUS AND SABLE VEHICLES EQUIPPED WITH POWER ADJUSTABLE PEDALS (RECALL 01V-078).RQ03-008 WAS OPENED TO INVESTIGATE COMPLAINTS CONCERNING THE REMEDY AND SCOPE OF 01V-078.ODI'S ANALYSIS IDENTIFIED CONCERNS WITH POST-REPAIR FAILURES IN RECALLED VEHICLES,FAILURES IN MY 2001-02 VEHICLES WITH ADJUSTABLE PEDALS THAT WERE NOT INCLUDED IN RECALL 01V-078, AND FAILURES IN MY 2000 VEHICLES WITH FIXED PEDALS.(NOTE: THE MANUFACTURER FAILURE DATA IN THIS RESUME INCLUDES ALL CRASHES AND INJURIES, BUT THE COMPLAINT INFORMATION IS LIMITED TO MY 2001-02 VEHICLES THAT WERE NOT INCLUDED IN THE SCOPE OF RECALL 01V-078.)ON MARCH 1, 2004, FORD NOTIFIED NHTSA OF A SAFETY DEFECT IN MY 2000 THROUGH EARLY-2003 TAURUS AND SABLE VEHICLES EQUIPPED WITH ADJUSTABLE PEDALS AND MY 2000 SUBJECT VEHICLES EQUIPPED WITH FIXED PEDALS (RECALL 04V-106).THE NOTIFICATION IDENTIFIED THREE FACTORS CONTRIBUTING TO BRAKE LIGHT CIRCUIT FAILURES:(1) CONTINUING GREASE CONTAMINATION ISSUES THAT PROMPTED 01V-078; (2) MISALIGNMENT OF THE BOOSTER ROD PIN AND THE BRAKE LIGHT SWITCH; AND (3) WIRE ASSEMBLY FATIGUE.THE FIRST TWO CONDITIONS WERE LIMITED TO VEHICLES WITH ADJUSTABLE PEDALS AND THE LATTER CONDITION AFFECTED VEHICLES WITH FIXED PEDALS.FORD WILL INSTRUCT OWNERS TO BRING THEIR VEHICLES TO A DEALER TO HAVE THE BRAKE LIGHT SWITCH AND ASSOCIATED WIRING REPLACED WITH A RE-DESIGNED BRAKE LIGHT SWITCH AND WIRING ASSEMBLY.

EXTERIOR LIGHTING:BRAKE LIGHTSLed to recall 04V106000

Elsewhere on this vehicle

Data sources

Data on this page last refreshed .