2018 Grand Design Reflection

The contact owns a 2018 Grand Design Recreational Reflection RV. The contact stated that there were structural cracks and frame separation on the RV, causing the rear interior walls to separate from the floor of the RV. The cause of the failure was not yet determined. The contact was informed of a Customer Satisfaction Campaign related to the failure. The vehicle was not yet repaired. The manufacturer and local dealer were not yet notified of the failure. The failure mileage was unknown.

NHTSA ID

11709891

Incident

Nov 1, 2025

A thin rubber grommet is used to protect the electric brake wires passing through the axel tube. These grommets wear through during normal towing. This, in turn, causes the wire to short to ground leading to total failure of the trailer brakes. I did not experience an accident but came very close as I was approaching a stopped vehicle and realized I needed MUCH more braking force on my truck brakes to stop my forward movement. All 4 grommets on the 2 axels on my trailer have failed as shown in the attached pictures but only one has resulted in the wire being rubbed through causing the brake failure. A picture of the axel ID is also included. This appears to be a serious design flaw that should be corrected. A quick Internet or YouTube search will show there are many occurences of this!

NHTSA ID

11613694

Incident

Sep 2, 2024

The contact owns a 2018 Grand Design Reflection RV. The contact stated stated after starting the RV, he noticed that there was fire coming out of the refrigerator compartment. The contact was able to extinguish the fire with 3 fire extinguishers, fire hoses, and with the assistance of the fire department. A fire department report was filed. A police report was filed, but the police report information was not available. The contact sustained a scraped left knee while exiting the RV, but did not seek medical assistance. The RV was towed to the contact's residence. The manufacturer was notified of the failure and informed that the VIN was included in NHTSA Campaign Number: 22V038000 (Equipment). Additionally, the manufacturer sent a field technician to the contact's residence, where the RV was inspected but the cause of the failure could not be determined. The dealer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 10,000.

NHTSA ID

11597322

Incident

Jun 24, 2024

Mileage

10,000 mi

Own 2018 Grand Design (GD) RV with a broken Lippert (LCI) spring hanger that holds the axle in place, not discovered until maintenance. Photos available. Research reveals longevity, LCI knowledge, fix, number of & lack of notification. Contacted dealer, GD & LCI about safety defect told “Out Of warranty.” Not warranty, safety. The GD RV requirement or LCI frame equipment component issue is the spring/axle hanger. Other RV manufactures utilize Lippert frames with the same component/condition. LCI RV frames experience a higher rate of spring/axle hanger failures than RV manufactures Northwoods or Outdoor RV that design and construct their own RV frames. Info GD Forum. Attached #1, 2, 3, 4. There are more. 7/2014 NHTSA Recall # 14V-288 Starcraft. #5 10/7/2016 Keystone Rv RECALL: 14V-146 Safety Advisory: 14-205. #6 4/ 23/2021 LGS Industries Inc, #7 Recalls based on quality. Current cause unknown, “may fail during travel leading to an increased risk of loss of control and vehicle crash” remains the same. March 6, 2022, post describes in detail the broken spring hanger issue, includes a mechanical drawing dated 2003 of Lippert designed V modification fix. #8 LCI Publication LIP-0135 revA, AXLE RETRO PROCEDURE developed for 2009 Open Range RV. Page 2, information/drawings how to modify spring hanger, with V mod. #9 On 12/2020, a post “This is what the spring hanger looks like with the V reinforcements factory installed on my ’21 31G.” Is Lippert now installing the V mod on new frames? #10 Educating RV owners, the importance of inspection & available V mod of potential hanger failure, would result in safer roads for owners & public. GD & LCI’s current absence of responsibility & involvement is unfair.

NHTSA ID

11587832

Incident

Mar 12, 2024

The contact owns a 2018 Grand Design Reflection. The contact stated that as he retracted the RV's main slide out, the actuator used to retract the slide out snapped. Due to the failure, the slide out remained loose and was no longer secured to the RV. A technician was called to inspect the RV but informed the contact that there was too much damage and that extensive repairs would be needed. The manufacturer was notified of the failure and informed the contact that the RV was no longer under warranty. The RV was not repaired. The failure mileage was unknown.

NHTSA ID

11522266

Incident

May 11, 2023

The contact owns a 2018 Grand Design Reflection. The contact stated that during maintenance of the vehicle, he noticed that the driver’s side rear upper shackle pin on the Dexter trailer axle was not drilled to allow lubricant grease to enter, causing the pin and spring to dry out. The vehicle was not taken to a dealer. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 9,000. Consumer contacted the RV manufacturer, Grand Design, who suggested he follow up with axle manufacturer, Dexter.

NHTSA ID

11439033

Incident

Sep 1, 2021

Mileage

9,000 mi

While towing my rv, the weld that secures the rear axle springs broke. This weld was located on the right rear side of the frame and it snapped completely off the Lippert frame. It allowed the rear axle to move forward and the two tires on the right side contacted each other and the tires started to disintegrate. A tire on the left side was forced out of alignment and the tire shaved rubber until the steel belts were visible. These tires were high grade tires with less than 5000 miles on them. I stopped for fuel and noticed the damage. If I had continued the tires would surely have had a catastrophic failure shortly. This would have certainly resulted in a loss of control and a probable crash at highway speed. Since the tires were rubbing it is also likely a fire could have resulted. I was unable to have the vehicle moved to a repair location and no mobile rv techs would respond since I was in a remote location. I had to hire a local welder to reattach the weld and reinforce the frame on both sides. In speaking with my insurance company it was determined that this is not an unusual problem with welds breaking. The vehicle was not inspected by police as no other individuals or property was involved. Photos of the damage and broken weld were sent to Grand Design and Lippert, the manufacturer of the frame. Photos taken of the repairs performed by the welder were also sent to them. In addition to repairing the broken weld, I had the welder reinforce the left side of the frame holding the axle springs in place so that it would not fail. The unit is now much safer than it was before the repair. There were no warning lights or symptoms for this problem. I stopped purely by chance for fuel and noticed the steel belts protruding through my tires and this is the only thing that stopped a catastrophic failure and probable crash. The trailer has never been overloaded, and was never driven faster than 65. It has never been in an accident.

NHTSA ID

11422612

Incident

May 9, 2021

THE SUSPENSION HANGER, THE PIECE THAT HOLDS LEAF SPRING AND IS ATTACHED TO THE FRAME OF THE TRAILER, BROKE CLEAN THROUGH ON INBOARD REAR PASSENGER SIDE OF THE VEHICLE. THE SUSPENSION FAILURE WAS DISCOVERED WHILE PARKED AND DURING ROUTINE LUBRICATION OF THE SUSPENSION WET BOLTS. THE COMPONENT IS AN INVERTED U BRACKET, THE TOP OF WHICH ATTACHES TO THE TRAILER FRAME, THE ARMS OF WHICH, IN CONJUNCTION WITH A WET BOLT PROVIDE THE MOUNTING LOCATION FOR THE REAR EYE OF THE LEAF SPRING. ONE LEG OF THIS U BRACKET, AND CONSEQUENTLY ONE END OF THE BOLT ATTACHING THE LEAF SPRING TO THE BODY COMPLETELY FAILED, BREAKING CLEAN AWAY FROM THE FRAME. UPON FURTHER INSPECTION THE REAR DRIVER SIDE LEAF SPRING BRACKET HAS DEVELOPED A CRACK, BUT HAS NOT PROPAGATED THROUGH THE ENTIRE ARM OF THE BRACKET. FORTUNATELY THIS SUSPENSION FAILURE WAS DISCOVERED WHILE THIS 10,000LB VEHICLE WAS PARKED AND FAIRLY EARLY AS THE ARM OF THE SUSPENSION HAD NOT YET HUNG TO A HANGING POSITION. WITH THE OTHER HANGER BEGINNING TO FAIL, THIS VEHICLE WOULD POSE A SIGNIFICANT HAZARD TO PERSONS AND PROPERTY WHILE TRAVELING AT HIGHWAY SPEEDS. THE VEHICLE IS LESS THAN 2 YEARS OLD, IT HAS BEEN TRAILERED LESS THAN 3000 MILES, HAS BEEN LOADED WITHIN GVWR LIMITS, HAS NEVER BEEN IN AN ACCIDENT, HAS SUSTAINED NO BODY DAMAGE. *DT CONSUMER CONTACTED MANUFACTURER OF THE FRAME AND SUSPENSION COMPONENTS. CARFAX CANNOT PROCESS THIS REQUEST. *JB

NHTSA ID

11209790

Incident

May 23, 2019

Mileage

2,700 mi

Lippert Components and Grand Design RV are launching a Customer Satisfaction Campaign to address frame web cracks appearing above the spring hangers on some Solitude 310GK & Reflection 303RLS models. The units affected were produced between June 2013 and May 2021.

Lippert Components and Grand Design RV are launching a Customer Satisfaction Campaign to address frame web cracks appearing above the spring hangers on some Solitude 310GK & Reflection 303RLS models. The units affected were produced between June 2013 and May 2021.

Lippert Components and Grand Design RV are launching a Customer Satisfaction Campaign to address frame web cracks appearing above the spring hangers on some Solitude 310GK & Reflection 303RLS models. The units affected were produced between June 2013 and May 2021.

Customer Satisfaction Program released to have a protective heat shield installed behind convection microwave on units identified below to address concerns with excessive heat buildup.

The #10 screws used to fasten the vertical column of the Schwintek In Wall system to the may have been over torqued, causing a loss of hold, resulting in loose and/or broken screwheads. As a result, columns may pull away from the sidewall.