RoadVitals

2016 Imt Dominator Recalls

Safety recall campaigns filed with NHTSA that cover this model year

Recalls apply to specific vehicles, not to every vehicle of a model year. Check your VIN with NHTSA or your manufacturer's dealer to confirm whether a recall affects your vehicle.

Check a VIN on NHTSA.gov
Recall campaignsA safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
2
Newest Aug 18, 2017
Carrying an NHTSA advisoryCampaigns where NHTSA told owners not to drive the vehicle, or to park it outside, until the repair is done.
0
Open investigationsNHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
0

Recall campaigns

2 campaigns cover this model year — what the defect is, what it could cause, and what the remedy is

17V515000

ELECTRICAL SYSTEM

Aug 18, 2017
38 units potentially affected
The defect: Iowa Mold Tooling Co., Inc. (IMT) is recalling certain 2016-2017 Dominator Contractor series trucks built on 2017 Ford Super Duty chassis. These vehicles are equipped with a front jump start plug kit installed under the hood at the chassis battery. The fuse block for this kit may contact the hood creating an electrical short.
The risk: An electrical short can increase the risk of a fire.
The remedy: IMT will notify owners, and dealers will replace the jump start kit mounting bracket, thereby relocating the fuse block, free of charge. The recall began on September 29, 2017. Owners may contact IMT customer service at 1-800-247-5958. IMT's number for this recall is TB2017006.
Iowa Mold Tooling Co., Inc.Manufacturer number TB2017006View on NHTSA.gov
16V088000

EQUIPMENT

Feb 16, 2016
822 units potentially affected
The defect: Iowa Mold Tooling Co., Inc. (IMT) is recalling certain model year 2013-2016 Dominator-Propane, Dominator I, Dominator II, Dominator III, and Dominator IV vehicles manufactured April 4, 2013, to January 22, 2016. The affected vehicles are fitted with IMT Series III cranes, models 6000, 7500, 8600, 9500, 10000, 12000, and 14000, which have a valve bank cover that may crack and fall from the crane while the vehicle is being driven.
The risk: If the valve bank cover detaches from the crane it could be a road hazard, increasing the risk of a crash.
The remedy: IMT will notify owners, and dealers will replace the valve bank cover with a thicker one, free of charge. The recall began on April 6, 2016. Owners may contact IMT customer service at 1-800-247-5958. IMT's number for this recall is TB2016002.
Iowa Mold Tooling Co., Inc.Manufacturer number TB2016002View on NHTSA.gov

What a recall is

Safety recall
A safety recall is issued when a manufacturer or NHTSA determines that a vehicle has a safety-related defect or does not comply with a federal motor vehicle safety standard. Recall repairs are free. Whether a specific vehicle is covered depends on its VIN — a recall listed for a model year does not necessarily apply to every vehicle of that year.
Safety investigation
NHTSA opens an investigation to examine whether a safety defect may exist. An open investigation is not a determination that a defect exists, and many investigations close without a recall. Investigations can, however, lead to one.
Manufacturer communication
Manufacturers file copies of the bulletins they send to dealers with NHTSA. These often describe diagnostic or repair procedures for a known condition. They are not recalls: repairs described in a bulletin are usually only free if the vehicle is still under warranty or the manufacturer has extended coverage.

Elsewhere on this vehicle

Data sources