2022 Jeep Wagoneer Problems

Liftgate Latch Assembly Failure: The vehicle experienced an internal electrical short circuit and hardware failure within the power liftgate latch assembly. This defective latch caused a severe parasitic 12V battery drain that repeatedly rendered the vehicle completely dead, leaving it unexpectedly stranded. The hardware failure also triggered a software error loop that locked the power liftgate into an inoperable mode (3-beep lockout). Replacing the liftgate latch assembly successfully resolved the liftgate operation and eliminated the parasitic drain. Uconnect 5 Software Defects: Independent of the physical liftgate issue, the Uconnect 5 infotainment system (currently running software build U29.42, referencing TSB 08-230-24) exhibits significant software bugs and display stability issues. The primary central screen frequently flickers, displays line artifacts, freezes, and repeatedly drops wireless Apple CarPlay connectivity. Additionally, when shifting the vehicle into reverse, the rear backup camera feed fails to load, displaying only a blank black screen instead of the camera view. This disables primary vehicle setting controls, navigation interfaces, and rearward safety visibility while operating the vehicle.

vehicle lost eng power would not restart had to be towed to dealership they conformed problem

My car blew an engine while I was inside the car. The car was in park and running in a parking lot when the parking brake automatically engaged unexpectedly. Then, the gauge cluster instructed me to press the brake and push the start/stop button. I then got a warning on my gauge cluster, this time notifying my car entered starter protection mode. Repeating the process three times, me, my four year-old daughter, and were put at high risk of suffering burns as my car started to give off a burning smell of oil, as well strong white smoke from the hood, and shut off the car and opened the hood to release the smoke. If I had waited longer, there would have been a fire. The car is available upon inspection and is currently at my local dealer as of 8/11/2026 (Thunder Chrysler Dodge Jeep Ram, Bartow, Florida) for repairs. An engine failure was confirmed by discoveries by the dealer of a broken valve spring, a dropped cylinder, a cracked piston head, and an oil-coolant mixture. The dealer confirmed that this stemmed from Stellantis's faulty "Multi-Displacement System" (MDS) cylinder-deactivation system and "eTorque" mild-hybrid system. Both systems work together to save fuel at cruising speeds and stoplights. However, due to the constant cycling of both systems, they contribute to the excessive engine stress and oil pressure fluctuation, which are known for the "WS" Jeep Wagoneer, the "DT" RAM 1500, and the "WL" Grand Cherokee equipped with the 5.7L HEMI eTorque V8. The dealer relayed the issues to Stellantis North America, showing videos and photos of this catastrophic mechanical failure.

vehicle lost eng power would not restart had to be towed to dealership they conformed problem

Due to braking system electronic failure vehicle automatically disables safety features such as ABS, parking collision sensors disabled, traction control, and vehicle will automatically and abruptly go into P (park) when coming to a stop while braking. This can be caused by wheel speed sensors, brake control module, or communication failure to PCM. Engine codes U0418, U0415, and U1003 linked to problem. This is a big safety hazard where vehicle damage or injury/death can occur to occupants of the vehicle. Safety features should never become disabled in a vehicle while in operation.

While driving my 2022 Jeep Wagoneer at 40-45 mph on a live public road with my four small children in the vehicle, the vehicle suffered a sudden, catastrophic electronic and powertrain shutdown without warning. The engine completely died, and the vehicle immediately and forcefully engaged the electronic emergency parking brake, bringing the vehicle to an abrupt, unexpected halt in the middle of moving traffic.Once stopped, the vehicle completely refused to crank or restart. The electronic shifter and braking system effectively locked the vehicle in place, leaving me and my four young children dangerously stranded inside a dead vehicle in the middle of a live lane, creating an immediate, life-threatening collision hazard from oncoming traffic. The vehicle had to be physically towed away from the scene to a dealership, where it currently sits awaiting diagnosis.This vehicle has a documented history of prior electronic and dashboard glitches that the manufacturer has failed to permanently resolve under warranty. The sudden loss of propulsion combined with autonomous, unwanted emergency brake activation while in motion represents a severe, un-remedied safety defect that put the lives of my entire family at immediate risk.

Due to braking system electronic failure vehicle automatically disables safety features such as ABS, parking collision sensors disabled, traction control, and vehicle will automatically and abruptly go into P (park) when coming to a stop while braking. This can be caused by wheel speed sensors, brake control module, or communication failure to PCM. Engine codes U0418, U0415, and U1003 linked to problem. This is a big safety hazard where vehicle damage or injury/death can occur to occupants of the vehicle. Safety features should never become disabled in a vehicle while in operation.

While cruising on the freeway at approximately 70 miles per hour with no vehicles or objects ahead. The vehicle suddenly made a loud warning sound and flashed a message on the dash. The emergency brakes were automatically applied and nearly stopped in the middle of the freeway. The car behind had to swerve to avoid a collision. The vehicle then resumed driving forward. I was using the adaptive cruise control.

Due to braking system electronic failure vehicle automatically disables safety features such as ABS, parking collision sensors disabled, traction control, and vehicle will automatically and abruptly go into P (park) when coming to a stop while braking. This can be caused by wheel speed sensors, brake control module, or communication failure to PCM. Engine codes U0418, U0415, and U1003 linked to problem. This is a big safety hazard where vehicle damage or injury/death can occur to occupants of the vehicle. Safety features should never become disabled in a vehicle while in operation.

While my wife was operating our 2022 Jeep Wagoneer Series III (5.7L HEMI eTorque, ~44,700 miles) at highway speed, the vehicle suffered a sudden and complete electrical power failure. Electric power steering cut out completely while the vehicle was in motion, creating an immediate safety hazard and nearly causing an accident. The vehicle was disabled and required towing. The dealership (Safford Jeep) diagnosed fault code P0B32: catastrophic internal hardware and voltage failure of the 48-volt eTorque Hybrid Battery Pack. The 12-volt battery was also destroyed as a consequence of the 48V pack failure — the 12V charges exclusively via a DC-to-DC converter fed by the 48V loop; when the pack failed, the converter lost power and the 12V battery was starved of charge. NOTE: This incident is consistent with the active NHTSA ODI preliminary evaluation of 2022 Jeep Wagoneer and Ram 1500 eTorque electrical failures. FCA/Stellantis has acknowledged these failures are likely caused by an electrical concern. My P0B32 event represents a catastrophic failure of the exact system under investigation, with the additional safety consequence of complete loss of power steering at highway speed. Stellantis Corporate Case #96719164 is open. The vehicle has been repaired (48V battery pack replaced) but Stellantis has declined to address the warranty access barrier created by their diagnostic system architecture. The dealer's equipment required a new 12-volt battery installation before it could communicate with the covered hybrid system — a $645 mandatory prerequisite to accessing a Federal Emissions Warranty repair.

I own a 2022 Jeep Wagoneer with the 5.7L HEMI eTorque system. The vehicle has lost all power while being driven on two separate occasions. The first occurred on October 22, 2025, on a major interstate. The second occurred on January 30, 2026, on a state highway. In both cases the engine shut off without warning while the vehicle was in motion, with my wife and four children aboard. Power steering and braking assist were lost. The vehicle locked into Park, and I could not get power to shift into neutral or restart it. The January 30 incident required towing. The vehicle was inspected by a mechanic, who was unable to replicate the problem. Since the second failure, I have observed that system voltage drops rapidly during normal driving on nearly every trip. To avoid another shutdown in traffic, I now monitor voltage and pull over to shut the engine off and restart it once it reaches 12.4V. This takes several efforts each trip to pull over and restart the system. It has produced anxiety in my family about the safety of this vehicle. This is a full-size SUV losing power in highway traffic without warning. It endangers my family and every driver around us. I am aware of ODI Preliminary Evaluation PE24018 covering this vehicle and system, and I am submitting this so my incidents are part of that record.

While driving on the highway going 70 mph, the vehicle lost all power and shut down engaging the automatic emergency brake system. This is the second time it has happened. Car is currently at dealership awaiting service.

UNKNOWN I have had this jeep to 3 different dealerships multiple times over the 2 years I have owned it. I am getting my 3rd set of tires put on today. I have put approx 30k on it. It is eating tires. Down to the belt. The vehicle starts to vibrate at 70mph. I just had it aligned in March 2026, they said tires were fine. Vehicle started to vibrate at high speeds again and I took it in. It is so far out of alignment that the belts are showing on the front right tire. I smell burning rubber almost after every drive. This cannot be safe. What is causing is to go out of alignment constantly? I have read multiple threads where this is a known issue and something needs to be done about it, PLEASE

2022 Wagoneer Series III has major alignment issues and ruining tires with the outside tire edges cupping/wearing bald due to the alignment kicking out within an hour of being aligned and driven at highway speeds. Vehicle also has a death wobble when going over 65 mph and pulls hard to the right almost causing the vehicle to go off the road or into another lane if you are not bare knuckling the steering wheel to the left to counteract the hard right pulling. Vehicle has been in and out of the Dealership since 12/2024 to address the problem, however FCA/Stellanis has come back with no fix or solution to the problem and states to bring the vehicle in every 3,000 miles to have an alignment done, which is unacceptable. The vehicle has most recently been at the Dealership since 1/2026 and is still currently at the Dealership as of today 6/5/2026. A Star ticket was opened with the Manufacturer to address the issues, and a Field Engineer was sent out who was unable to diagnose why the alignment is falling out after the vehicle is realigned. Stellanis/FCA is now claiming this is a "maintenance" issue and not a manufacturing defect. The Dealership most recently had an independent technician who specializes in diagnostics/troubleshooting FCA issues look at the vehicle and the technician also could not diagnose why the alignment is continuing to fail. Online forums have hundreds of Consumer complaints about this same issue with trying to get it resolved with FCA directly and having no luck. This is a major safety issue that will eventually lead to a tire blowout or veering off the road and could result in serious injuries to someone if this is not addressed properly. It should not take someone getting in an accident or being killed/seriously injured for FCA/Stellanis to take this manufacturing defect seriously. These vehicles need to be recalled and thoroughly inspected with thorough alignment testing.

The right second row passenger seat in a 2022 Jeep Wagoneer appeared to be pushed fully rearward into its normal seating position and produced an audible/tactile click. No warning lamp or message indicated that the seat was not latched. While traveling approximately 40 to 45 mph, the driver had to brake hard. During braking, the entire right second row seat moved rapidly forward and pinned a child and the child restraint against the front passenger seat. The child struck the side of her head, was evaluated in an emergency department, and was diagnosed with a mild concussion. After the vehicle stopped, the seat was pushed rearward only to free the child. It then latched and is currently available for inspection. The seat has not been tested or operated since. The exact cause is UNKNOWN. Possible causes include incomplete latch engagement, a latch or actuator malfunction, or a failure of the seat position warning system. The vehicle has a prior documented warranty repair involving the opposite second row seat. In October 2024, that seat’s motor could be heard operating but the seat would not release. The dealer diagnosed a weak release motor and replaced two folding seat motor actuators under warranty. The current failure has not yet been reproduced or confirmed by a dealer. The vehicle and seat have not yet been inspected by the manufacturer, police, insurer, or an independent repair facility. Photographs, hospital records, and the prior warranty repair record are available. A case has been opened with Stellantis.

Car seat has been installed in Jeep Wagoneer for approximately 3 months. Was installed by a CPST. 25 lb rear-facing child; installed with lower latch anchors. When placing child in seat one day, CPST-caregiver suddenly noticed movement in the seat and confirmed more than 1 inch of movement at the belt path. Upon removal to reinstall, it was noted that the Snuglock lockoff arm was no longer locked in place. Child's safety was put at risk because there was no longer a secure install of the car seat. Car seat only inspected prior to reinstall by CPST-caregiver. Car seat available for inspection upon request. Car seat still in use.

UNKNOWN I have had this jeep to 3 different dealerships multiple times over the 2 years I have owned it. I am getting my 3rd set of tires put on today. I have put approx 30k on it. It is eating tires. Down to the belt. The vehicle starts to vibrate at 70mph. I just had it aligned in March 2026, they said tires were fine. Vehicle started to vibrate at high speeds again and I took it in. It is so far out of alignment that the belts are showing on the front right tire. I smell burning rubber almost after every drive. This cannot be safe. What is causing is to go out of alignment constantly? I have read multiple threads where this is a known issue and something needs to be done about it, PLEASE

2022 Wagoneer Series III has major alignment issues and ruining tires with the outside tire edges cupping/wearing bald due to the alignment kicking out within an hour of being aligned and driven at highway speeds. Vehicle also has a death wobble when going over 65 mph and pulls hard to the right almost causing the vehicle to go off the road or into another lane if you are not bare knuckling the steering wheel to the left to counteract the hard right pulling. Vehicle has been in and out of the Dealership since 12/2024 to address the problem, however FCA/Stellanis has come back with no fix or solution to the problem and states to bring the vehicle in every 3,000 miles to have an alignment done, which is unacceptable. The vehicle has most recently been at the Dealership since 1/2026 and is still currently at the Dealership as of today 6/5/2026. A Star ticket was opened with the Manufacturer to address the issues, and a Field Engineer was sent out who was unable to diagnose why the alignment is falling out after the vehicle is realigned. Stellanis/FCA is now claiming this is a "maintenance" issue and not a manufacturing defect. The Dealership most recently had an independent technician who specializes in diagnostics/troubleshooting FCA issues look at the vehicle and the technician also could not diagnose why the alignment is continuing to fail. Online forums have hundreds of Consumer complaints about this same issue with trying to get it resolved with FCA directly and having no luck. This is a major safety issue that will eventually lead to a tire blowout or veering off the road and could result in serious injuries to someone if this is not addressed properly. It should not take someone getting in an accident or being killed/seriously injured for FCA/Stellanis to take this manufacturing defect seriously. These vehicles need to be recalled and thoroughly inspected with thorough alignment testing.

The contact owns a 2022 Jeep Wagoneer. The contact stated that while a family friend was driving on the freeway at approximately 70 MPH, the vehicle suddenly stalled. The Mobile repair unit was called to the scene and diagnosed the vehicle with fuel pump failure. The contact was informed that the fuel pump needed to be replaced. The vehicle was towed to a nearby parking lot. The local dealer and manufacturer were notified of the failure and informed the contact that the part was on back order and not currently available for purchase. The vehicle was not repaired. The contact was informed of NHTSA Action Number: PE24018 (ELECTRICAL SYSTEM, HYBRID PROPULSION SYSTEM, ENGINE, ENGINE AND ENGINE COOLING); and associated the failure with the campaign. The failure mileage was 77,000.

The vehicle experienced a charging system failure while driving. The battery warning light illuminated and battery voltage dropped to approximately 11.7 volts while the engine was running. The vehicle continued to discharge the battery while being driven, creating a risk of loss of electrical power and possible vehicle shutdown. Diagnostic trouble codes included P0562 (System Voltage Low), P0BDE (Drive Motor Inverter Temperature Sensor E Circuit High), and P0AEE (Drive Motor Inverter Temperature Sensor A Circuit Range/Performance). The charging system was inspected by an independent repair facility. The serpentine belt was verified to be functioning properly and related fuses were checked. The repair facility diagnosed a failure of the 48-volt eTorque Belt Starter Generator (Motor Generator Unit/MGU). The replacement part is reportedly on backorder. The condition is repeatable and occurs during normal driving. The battery warning lamp and low voltage condition were observed and documented. This failure creates a potential safety concern because the vehicle can lose charging capability while operating on public roads.

Liftgate Latch Assembly Failure: The vehicle experienced an internal electrical short circuit and hardware failure within the power liftgate latch assembly. This defective latch caused a severe parasitic 12V battery drain that repeatedly rendered the vehicle completely dead, leaving it unexpectedly stranded. The hardware failure also triggered a software error loop that locked the power liftgate into an inoperable mode (3-beep lockout). Replacing the liftgate latch assembly successfully resolved the liftgate operation and eliminated the parasitic drain. Uconnect 5 Software Defects: Independent of the physical liftgate issue, the Uconnect 5 infotainment system (currently running software build U29.42, referencing TSB 08-230-24) exhibits significant software bugs and display stability issues. The primary central screen frequently flickers, displays line artifacts, freezes, and repeatedly drops wireless Apple CarPlay connectivity. Additionally, when shifting the vehicle into reverse, the rear backup camera feed fails to load, displaying only a blank black screen instead of the camera view. This disables primary vehicle setting controls, navigation interfaces, and rearward safety visibility while operating the vehicle.

UNKNOWN I have had this jeep to 3 different dealerships multiple times over the 2 years I have owned it. I am getting my 3rd set of tires put on today. I have put approx 30k on it. It is eating tires. Down to the belt. The vehicle starts to vibrate at 70mph. I just had it aligned in March 2026, they said tires were fine. Vehicle started to vibrate at high speeds again and I took it in. It is so far out of alignment that the belts are showing on the front right tire. I smell burning rubber almost after every drive. This cannot be safe. What is causing is to go out of alignment constantly? I have read multiple threads where this is a known issue and something needs to be done about it, PLEASE

This vehicle is not equipped with an Auto High Beam feature. The result of this is that when the Headlights are in Auto Mode, the Manual control of the High Beams is disabled. Most people leave their headlights in Auto mode to ensure that they dont forget to turn them on or off, but then the high beams are inoperable. This can pose a significant safety concern when you consider that when someone is driving and needs the use of the high beams they have to take their eyes off the road to fumble around with the headlight dial so they can turn it to manual to enable the use of the high beams.

The main head unit for the infotainment system, specifically the software. Upon failing a software update in August 2024, the vehicle started switching itself from English to Italian, from Standard to Metric units, the high beams would no longer function, the auto locking doors after 15mph would no longer work, the emergency pedestrian sensing braking was turned off, the entire infotainment screen randomly shuts off and comes back on as well. Without readily available high beams my ability to see further distances at night was diminished. 2)The uninitiated change in language and units of measure made it more difficult to verify vehicle speed and other important settings with intervention to return the system to English. 3) Largest concern, auto locks not turning on, without notifying the driver, left my young children at risk of opening the back doors and falling out of the vehicle at high speeds. The dealership has tried to fix this twice, they have updated the software to current version and reset the system. They also reset the customer programmable features, which corrected the issue with the high beams, but the other issues with software remain, including the auto locks at speed, language change, units change and screen shutting off and on. I have also contacted Jeep customer service, they do not have a remedy in place and verified the software is up to date. After reviewing Jeep Wagoneer forums, this is effecting many owners of the Wagoneer after that fall 2024 update, and all the dealerships are scratching their heads. But without autolocks at speed, this is a big issue. No warning lights came on to let me know, and the bug seems to be in all software versions for the Wagoneer from Fall 2024 to current.

While driving down the freeway at 70mph the sunscreen had a spontaneous sunroof explosion on the freeway. As it flew off the vehicle it damaged the top of the body with deep gouges along to of the vehicle. We had the sunscreen closed over us at the time or my infant daughter would have been seriously hurt by the explosion of glass and the driver and passenger at the time would have had glass raining from them. There was no one in front of us when this occurred and happened with no warning or any visible damage prior to the incident.

Rearview and 360-degree surround camera intermittently fails or displays a blank/no image when reverse is selected. Failure behavior matches NHTSA recalls 23V-577 and 24V-436 for the same model, but this VIN is excluded from the recall population. Issue affects rear visibility and compliance with FMVSS 111. Dealer and manufacturer have been notified.

When driving the car this winter, noticed the smell of something burning. After that, the heated steering wheel stopped warming. Took it to a repair shop since there was open no recall related to this. Repair shop diagnosis: - heated steering wheel not working due to electrical short. More info below, pictures included. Finding Confirmed customer concern. Attempted to activate the heated steering wheel and found the light to come on for roughly 4-5 seconds then shut itself off. Scanned the vehicle and found 2 fault pertaining to the heating element and steering wheel having an open circuit. Removed the airbag and visually inspected all connectors for the steering wheel. Found the 2 pin connector from the steering wheel to the clock spring to be stuck in the clock spring. Further removed the steering wheel and trim pieces around the steering column and visually inspected the clock spring. Found the 2 pin connector between the steering wheel and the clock spring to be melted together and noticed the wires were getting hot to touch when activating the heated steering wheel. Back probed the connector between the clock spring and the heated steering wheel connector and found less than 2 volts present. Monitored and found while the steering wheel was being moved left to right the voltage would fluctuate dramatically. Recommend replacing the air bag clock spring and steering wheel due to melt damage and further monitor voltage and functionality of the heated steering wheel and other accessories. Highly recommend not operating the heated steering wheel until repairs have been made. Could cause more damage to the surrounding components.

Driving down the highway and another car turned into my lane. I turned/swerved to the left to avoid collision and all side and curtain airbags deployed in the vehicle. I did not crash into anything. There was zero damage to the exterior of my vehicle. The manufacturer (Stellantis) claims there is nothing wrong with the vehicle, and that it detected the vehicle was going to roll over, and that is why the airbags deployed. The vehicle was not going to roll over, the airbags deploying was the most dangerous thing that occurred. I was not able to see to either side, but was able to pull over to the median and come to a stop. The vehicle was inspected by the manufacturer hired engineer. The manufacturer would not give me any information or a copy of his report/inspection. There were no warnings before this happened. I had my 9mth old baby in the back seat. With no vision out the side, we were both put at risk, as well as any others on the highway. The scare of airbags deploying when no collision occurred was very intense.

3rd row seat belt is fraying/cut. Appears to be from the mechanism in the roof of the car. Jeep is refusing to replace it. And trying to charge 1500 dollars for the repair. It is a major safety concern as if someone was in that seat and were involved in a car accident the seatbelt would not work properly