2005 Mercedes-Benz 211

WHILE DRIVING THE CAR WILL SHUT OFF RANDOMLY AT HIGH SPEEDS ON THE FREEWAY AND I WILL LOSE STEERING AND MY BRAKING ABILITIES. THE SBC PUMP ALREADY HAD BEEN REPLACED AND MERCEDES HAS NOT MADE ANY ATTEMPT TO REIMBURSE ME, MULTIPLE AREAS OF THE WIRING HARNESS WILL CRUMBLE IN YOUR HAND INSIDE THE ENGINE COMPARTMENT, THE TRUNK HAD PINCHED WIRES SHORTING OUT AND CAUGHT FIRE LUCKILY I HAD BEEN IN THE GARAGE AT THAT TIME TO WITNESS AND PUT IT OUT. THE CAR WILL START UP AND DRIVE AND STALL OUT RANDOMLY NOW AT ANY SPEEDS OR EVEN BEING STOPPED.

NHTSA ID

11128317

Incident

Aug 27, 2018

Mileage

120,000 mi

CAR WENT INTO BRAKE FAILURE BARELY COULD STOP THE CAR ONCE IN PARK COULD NOT GET INTO DRIVE

NHTSA ID

11067330

Incident

Feb 6, 2018

THIS VEHICLE IS EQUIPPED WITH SENSOTRONIC BRAKE CONTROL THAT HAS A SERVICE THRESHOLD. WHEN THIS THRESHOLD IS REACHED THE BRAKE SYSTEM DEFAULTS TO NON POWER ASSISTED HYDRAULIC MODE TO THE FRONT WHEELS ONLY. THIS OCCURS WITHOUT ANY PRIOR WARNING AND RESULTS IN INCREASED STOPPING DISTANCE. I HAVE SENT A COPY OF THE MERCEDES SERVICE BULLETIN S142.46-P-0012A WHICH ADDRESSES THIS ISSUE. MERCEDES STOPPED INSTALLING THIS SYSTEM IN 2006. AT THE VERY LEAST, MERCEDES SHOULD ISSUE A MANDATORY RECALL TO INTERROGATE THESE VEHICLES WITH STAR DAS TO DETERMINE HOW CLOSE TO THE SERVICE THRESHOLD THE SBC UNIT IS AND REPLACE THEM AT THE DEALER'S EXPENSE. THIS IS A MAJOR SAFETY ISSUE THAT NEEDS TO BE ADDRESSED.

NHTSA ID

11044436

Incident

Nov 2, 2017

Mileage

143,000 mi

I WAS DRIVING MY MERCEDES E320 2005 ON I-75 AND TOOK EXIT 107. WHEN I PUSHED MY BRAKE PEDDLE I HAD WHAT SEEMED TO BE NO BRAKES AND A RED WARNING LIGHT CAME ON THE DASH. I RAN THE CAR OFF ON THE GRASS TO SLOW THE CAR DOWN. I HAD A GREEN LIGHT AND RAN ON THE SIDE STREET. THIS COULD HAVE BEEN A VERY DANGEROUS SITUATION. I AM UPSET THAT MERCEDES WOULD DESIGN A SYSTEM THAT COULD DO THIS.

NHTSA ID

11000927

Incident

Jun 21, 2017

Mileage

83,000 mi

SBC BRAKE FAILURE ALMOST CAUSES ACCIDENT. I WAS DRIVING DOWN A 2 LANE HIGHWAY AT 60MPH AND STEPPED ON THE BRAKES. AT THE MOMENT I STEPPED ON THE BRAKES THE DASHBOARD STARTED TO BLINK RED AND BEEPING WITH BRAKE FAILURE MESSAGE AND THERE WAS NO NOTICEABLE BRAKE POWER. I PUSHED THE PEDAL ALL THE WAY TO THE FLOOR AND FELT NO RESISTANCE AND VERY LITTLE BRAKING POWER. I'M ESTIMATING 5% POWER FROM NORMAL. I HAD TO SWERVE TO AVOID THE CAR IN FRONT OF ME. LUCKILY, THERE WAS NO TRAFFIC IN THE INTERSECTION BECAUSE I BLEW STRAIGHT THROUGH IT AND EVENTUALLY MANAGED TO GET THE VEHICLE STOPPED AFTER ABOUT 200 YARDS. THIS HAPPENED WITH NO PRIOR MESSAGES OR WARNINGS ON THE DASHBOARD. I TURNED OFF THE CAR AND RESTARTED IT AND BRAKING POWER RESUMED AS NORMAL. THERE ARE CURRENTLY NO MESSAGES ABOUT BRAKES. IT'S LIKE IT NEVER HAPPENED. *TR

NHTSA ID

10943757

Incident

Jan 8, 2017

Mileage

148,000 mi

STRONG SMELL OF GASOLINE VAPORS IN GARAGE WHEN VEHICLE HAS A FULL TANK. FAINT SMELL DETECTABLE IN PASSENGER COMPARTMENT. SMELL SUBSIDES WHEN FUEL TANK LEVEL REACHES 3/4 TO 1/2 FULL.

NHTSA ID

10899135

Incident

Jan 1, 2015

Mileage

50,000 mi

THIS VEHICLE IS EQUIPPED WITH SENSOTRONIC BRAKE CONTROL THAT HAS A SERVICE THRESHOLD. WHEN THIS THRESHOLD IS REACHED THE BRAKE SYSTEM DEFAULTS TO NON POWER ASSISTED HYDRAULIC MODE TO THE FRONT WHEELS ONLY. THIS OCCURS WITHOUT ANY PRIOR WARNING AND RESULTS IN INCREASED STOPPING DISTANCE. I HAVE SENT A COPY OF THE MERCEDES SERVICE BULLETIN S142.46-P-0012A WHICH ADDRESSES THIS ISSUE. MERCEDES STOPPED INSTALLING THIS SYSTEM IN 2006. AT THE VERY LEAST, MERCEDES SHOULD ISSUE A MANDATORY RECALL TO INTERROGATE THESE VEHICLES WITH STAR DAS TO DETERMINE HOW CLOSE TO THE SERVICE THRESHOLD THE SBC UNIT IS AND REPLACE THEM AT THE DEALER'S EXPENSE. THIS IS A MAJOR SAFETY ISSUE THAT NEEDS TO BE ADDRESSED.

NHTSA ID

10812021

Incident

Dec 22, 2015

Mileage

74,000 mi

CAR BRAKES DID NOT WORK. THE CAR BRAKES FAILED WHILE DRIVING. A RED LIGHT CAME ON THE DASH SAYING "REDUCED BRAKING POWER".

NHTSA ID

10788820

Incident

Nov 2, 2015

Mileage

146,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. • If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: • LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system