2006 Mercedes-Benz AMG C55

VERY STRONG FUEL ODOR INSIDE CABIN OF VEHICLE WHILE DRIVING. ODOR IS VERY STRONG AROUND DRIVERS REAR WHEEL AND FROM THE OUTSIDE ONCE PARKED. SMELL OF FUEL IS VERY STRONG AT TIMES WHILE DRIVING BUT SEEMS TO DISSIPATE WHEN DRIVING AT A FASTER SPEED I.E. ON HIGHWAY OVER 45MPH. ONCE I COME TO A STOP OR DRIVE BELOW 45MPH THE SMELL IS PRONOUNCED PROBABLY BECAUSE IT ISN'T BEING BLOWN AWAY FROM THE VEHICLE WHILE DRIVING. DOES NOT CHANGE IN CORRELATION TO FUEL TANK FILL LEVEL. INSPECTED FUEL SENDER UNDER ACCESS CAP, UNDERNEATH REAR PASSENGER BENCH DRIVER'S SIDE ON APRIL 9TH 2021. FOUND FUEL PUDDLING IN/AROUND THE EXTERIOR OF FUEL SENDING UNIT. CLEANED OUT FUEL PUDDLE. MOST OF THESE SYMPTOMS ARE ALSO SIMILAR TO CASE WITH THE 2003-2006 MERCEDES BENZ E55 AMG AND CLS VEHICLES FOUND UNDER NHTSA ACTION NUMBER: EA13003 REGARDING EMISSIONS RECALL FOR AMG MODELS USING HIGH PRESSURE FUEL SYSTEMS.

NHTSA ID

11407341

Incident

Apr 9, 2021

Mileage

117,000 mi

STARTED VEHICLE AND WHEN IN MOTION, I TURNED THE STEERING WHEEL, THE VEHICLE SHUDDERED AND MADE A LOUD GRINDING NOISE. CHECKED STEERING FLUID, AND IT WAS BELOW THE MINIMUM FLUID LEVEL. REFILLED STEERING FLUID RESERVOIR TO PROPER LEVELS AND VEHICLE NO LONGER MADE ANY NOISES OR STRUGGLED TO TURN THE STEERING WHEEL. SEVERAL DAYS LATER THE NOISE AND DIFFICULTY STEERING RETURNED WHEN IN MOTION AND TURNING THE STEERING WHEEL. CHECK STEERING FLUID RESERVOIR AND IT WAS BELOW THE MINIMUM FILL REQUIREMENT. INSPECTED BELOW THE VEHICLE AND THERE WAS A LOT OF STEERING FLUID COVERING PASSENGER SIDE SUSPENSION SYSTEM AND SLOWLY DRIPPING FROM THAT AREA. POSSIBLE LEAK FROM PRESSURE HOSE. CONTACTED MULTIPLE MERCEDES-BENZ DEALERSHIPS FOR PART # 209-466-00-81 PRESSURE HOSE AND IT WAS NOT AVAILABLE. IT IS ON WORLD WIDE BACK ORDER WITH NO TENTATIVE DATE FOR REPLACEMENT. I'M NOW UNABLE TO DRIVE VEHICLE DUE TO AN UNAVAILABLE PART WITH NO DATE ON WHEN I COULD DRIVE DRIVE THE VEHICLE. THE LEAK SEEMS TO BE DRIPPING ONTO THE FRONT SWAY BAR WITH ABOUT A DROP PER MINUTE. SEE IMAGE ATTACHED.

NHTSA ID

10957555

Incident

Feb 16, 2017

Mileage

136,000 mi

VERY STRONG FUEL ODOR INSIDE CABIN OF VEHICLE WHILE DRIVING. ODOR IS VERY STRONG AROUND DRIVERS REAR WHEEL AND FROM THE OUTSIDE ONCE PARKED. ALSO NOTICED GASOLINE/FUEL ACCUMULATION UNDERNEATH VEHICLE AROUND DRIVER'S SIDE REAR, ON UNDER BODY PANELS. SMELL OF FUEL IS VERY STRONG AT TIMES WHILE DRIVING BUT SEEMS TO DISSIPATE WHEN DRIVING AT A FASTER SPEED I.E. ON HIGHWAY OVER 45MPH. ONCE I COME TO A STOP OR DRIVE BELOW 45MPH THE SMELL IS PRONOUNCED PROBABLY BECAUSE IT ISN'T BEING BLOWN AWAY FROM THE VEHICLE WHILE DRIVING. DOES NOT CHANGE IN CORRELATION TO FUEL TANK FILL LEVEL. INSPECTED FUEL SENDER UNDER ACCESS CAP, UNDERNEATH REAR PASSENGER BENCH DRIVER'S SIDE ON AUGUST 27TH 2016. FOUND FUEL PUDDLING IN/AROUND THE EXTERIOR OF FUEL SENDING UNIT. FUEL SENDING PART NUMBER A209-470-04-94 CLEANED OUT FUEL PUDDLE AND REINSPECTED ACCESS TO PANEL TO FUEL SENDER ON SEPTEMBER 3RD AND FOUND THE FUEL SENDER AREA HAS PUDDLED WITH GASOLINE AGAIN. CHECK ENGINE LIGHT PERIODICALLY TURNS ON WITH CODE P0171 USUALLY A MONTH IN BETWEEN DATING BACK TO 2015. COINCIDING WITH THE FUEL SMELL. INSPECTED GAS CAP/FILLER TUBE FOR LEAKS AS PRECAUTION BUT FOUND NO LEAK. MOST OF THESE SYMPTOMS ARE ALSO SIMILAR TO CASE WITH THE 2003-2006 MERCEDES BENZ E55 AMG VEHICLES FOUND UNDER NHTSA ACTION NUMBER: EA13003 REGARDING EMISSIONS RECALL FOR AMG MODELS USING HIGH PRESSURE FUEL SYSTEMS.

NHTSA ID

10906902

Incident

Aug 27, 2016

Mileage

130,000 mi

ALL OF THE WIRES GOING TO (AND INSIDE) THE HEADLAMPS HAVE INSULATION CRACKING AND FALLING OFF, EXPOSING BARE WIRES, WITH THE LIKELIHOOD OF CAUSING A SHORT. I NEED TO REMOVE THE HEADLAMPS TO HAVE THEN "RESTORED", BUT MAY NEED TO REPLACE HEADLAMPS BASED ON WIRE ISSUE(S), AT $800 PER LAMP. *TR

NHTSA ID

10633194

Incident

Jun 20, 2014

Mileage

73,400 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).