2019 Mercedes-Benz AMG E63S

I brought my car in for routine service and was told I needed a rear main seal. I had the car inspected when I purchased it appx 13k miles ago because I saw online there was a lot of people having this issue with their vehicles. It’s a known manufacturer defect. At that time there was no issue. Now at 40k miles it began to leak. This is round about the mileage most people have experienced this issue. A car with 40k miles shouldn’t have a defect like this that could cause the vehicles oil to leak out the seal and destroy the motor. I believe MBUSA should be replacing all of these seals on all of the affected vehicles. A consumer shouldnt be charged $6500 at 40k miles to repair a seal that is failing on so many vehicles.

NHTSA ID

11708627

Incident

Jan 1, 2026

CAR DOES NOT ALWAYS RECOGNIZE WHEN THE DRIVERS SEAT BELT IS BUCKLED. THIS RESULTS IN THE PRETENSIONER NOT ACTIVATING AND THE SEAT BELT WARNING FROM BEING DISARMED.

NHTSA ID

11166147

Incident

Dec 7, 2018

Mileage

400 mi

Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

Complaint Noises in the steering column area when steering. See example file in the attachments area: "MRSM‑Schleifgeräusch_SCCMGrindingNoises. MOV". Cause Under analysis. Remedy Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: ‑ Loosen screws of the MRSM/SCCM and steering wheel, re‑align the MRSM/SCCM, and re‑fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. ‑ If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. ‑ If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. ‑ If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: ‑ When installing the MRSM/SCCM, make sure that no damage occurs! ‑ If the noise is due to the steering wheel (see attachment "Lenkrad‑Schleifgeräusch_SteeringWheel‑GrindingNoises.mp4"), please use LI46.10‑P‑077313. ‑ Only disassemble and mount all component parts in the "straight‑ahead position" (see also WIS). ‑ Please refer to this LI in the "Notes" section of the warranty claim!

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Red coolant warning in instrument cluster. Fault codes U019F00 or U019F87 current/stored in MRG1 control unit. Cause Various causes Remedy Perform guided test for fault code U019F with XENTRY diagnosis. Verify the following connections are clean and tight. Correct any problems and retest pump actuation: ‑12V plug at M75/11 ‑48V plug at M75/11 ‑48V connector X192/4 ‑Connections at 48V fuse box F153/2 ‑Sockets 1,2, and 5 at connector 2 of MRG1 control unit ‑M75/11 circuit 41 ground If actuation and above connections are OK, but resistance between M75/11 and engine block is less than 2 ohms or heat shield touching coolant pump, proceed with below steps. 1‑Modify engine insulation per attached instructions. 2‑Remove engine control module and measure continuity within control unit between connector 2 pin 1 and connector 6 pin 2. 2a‑If open circuit is found, replace engine control unit (MRG1) and perform initial startup. Refer to XENTRY parts information group 54/054 item 300. 3‑Clear faults and verify M75/11 operating normally.

Complaint Only vehicles with a variable transfer case are affected. This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 ‑ All‑wheel drive (ARS) N127 ‑ 'Drivetrain' (PTCU) control unit Y3/8 ‑ Transmission control for 9‑gear transmission (VGS) N3/10 ‑ Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications ‑ Collect an oil sample of the original fluid 5. Complete all transfer case Tech‑in processes located under VG Control Unit > Adaptations ‑ Resetting the oil service data ‑ Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature (>60C ) 6. Operate vehicle in full circle with steering at full lock ‑ 5x to the left ‑ 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If this LI has already been applied to the vehicle, please submit a TIPS case to the Powertrain inbox with the following information: ‑ Initial quick test with fault freeze frame data ‑ Initial transmission EEPROM data ‑ VGS and Transfer Case Control Unit Log (N45 or N15/7) ‑ Special Acquisition Data .txt file (Transfer Case Control Unit > Special Procedures > Procedures for support queries to market support > Special Data Acquisition) ‑ Photo of the original oil condition ‑ What color was the fluid drained from the transfer case before the oil change? ‑ Was an oil sample collected, and can you provide a photo of the original fluid? ‑ What color and part number fluid was used during the oil change? ‑ How far was the vehicle driven after?

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!