2018 Mercedes-Benz AMG GLE63

On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183

I GOT 9000 MILES ON MY 2018 MERCEDES BENZ GLE AMG 63S COUPE I AM GOING FOR MY SECOND SET OF BREAKS

NHTSA ID

11193713

Incident

Mar 28, 2019

Mileage

8,000 mi

BRAKES NEED REPLACING AFTER ONLY 11 MONTHS OLD AND 14,000 MILES. LOUD SQUEALING FROM BRAKES UPON APPLYING THEM. THIS HAS BEEN A PROBLEM SINCE PURCHASING THE CAR IN JAN. 2018. REPORTED TO DEALERSHIP MULTIPLE TIMES AND WAS TOLD IT WAS NORMAL. NOW THEY WANT ME TO PAY TO HAVE THE BRAKES REPLACED.

NHTSA ID

11161939

Incident

Dec 14, 2018

This NCU replaces the prior NCU issued on May 15, 2025, and contains additional MY 2023 and MY 2024 vehicles which are highlighted below. In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (“MBUSA”) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (“MY”) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: •Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (‘MIL’).

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. Vehicle production date prior to December 2025. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.