2013 Mercedes-Benz C250

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Airbags didn’t deploy during accident, vehicle hit on drivers side, greatly impacted, driver seatbelt was on. All recalls were completed. Impact from other vehicle that hit my vehicle had deployed airbags.

NHTSA ID

11765519

Incident

Sep 18, 2026

Over the past few weeks Ive had instances where the car has power but wont crank, Ive had the SRS light come on the dash but after it starting it goes away.

NHTSA ID

11744047

Incident

Jun 1, 2026

REAR SUB FRAME RUST NEEDS INSPECTED SUPER CLANKY

NHTSA ID

11742978

Incident

Mar 1, 2026

ESL emulator is bad. Keeps no crank Steering lock Also sunroof water spouts are not working as they should they do no open to release water.

NHTSA ID

11715179

Incident

Dec 1, 2025

The vehicle was represented to me as safe to drive, with no major mechanical issues, and that it would pass emissions after only a simple minor fix. After I took possession, the check engine light came on. The car began running rough and showing hesitation. A scan immediately showed a camshaft position sensor fault, cylinder misfire, lean fuel condition, and oxygen sensor/emissions faults. I was also told by a professional shop that the timing chain may be failing. I was then warned that these problems can cause power loss or engine stalling while driving, and that the vehicle in this condition would likely not pass a legal emissions inspection. I was never told about any of these safety or emissions problems before taking the vehicle. This situation creates a safety risk because sudden loss of engine power or stalling can happen in traffic.

NHTSA ID

11697039

Incident

Oct 29, 2025

News Channel Update | Warranty Mercedes-Benz USA, LLC A Mercedes-Benz AG Company One Mercedes-Benz Drive Sandy Springs, GA 30328 770.705.0600 IMPORTANT EXTENDED WARRANTY INFORMATION Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (“MY”) 2012-2015 Mercedes-Benz Model 204 and 172 vehicles (C250 and SLK250), the warranty on the camshaft adjuster will be extended from the original 4 years/50,000 miles to 10 years/120,000 miles (whichever occurs first) from the original warranty start date. This camshaft adjuster extended limited warranty applies to all conditions that necessitate the replacement of the camshaft adjuster under the standard warranty terms and conditions. The extended warranty is applicable to the following vehicles: Model Years Sales Designation Engine Type C-Class 2012-2014 C250 M271 C-Class 2012-2015 C250 Coupe M271 SLK-Class 2012-2015 SLK271 Please be advised that all camshaft adjusters being claimed under warranty must have a short test with fault code attached and will be inspected. All camshaft adjusters found to be functioning properly or without proper documentation will be returned and the claim debited in full. The following damage codes and parts kit can only be claimed for the replacement of the camshaft adjuster: Damage Code: 05050 – Camshaft adjustment, intake camshaft Damage Code: 05052 – Camshaft adjustment, exhaust camshaft Parts: A 271 050 21 00 80 – Camshaft adjuster, kit IMPORTANT: 1. Always check VMI to determine if a vehicle is covered under the 10 year/120,000 mile warranty period 2. Short Test Documentation with fault code information (P001477, P001600, P001762, P001662, P001177, P001700, P001192, P001492, P034062, P036662) must be attached to all returned camshaft adjusters Please check the VIN in Netstar/VMI before scheduling the appointment for the repair. Applicable vehicles will be visible in Netstar/VMI on October 30, 2020

NHTSA ID

11658655

Incident

Feb 10, 2022

Hola a todos. hace 3 meses compre un mercedes benz c250 año 2012 en argentina. A eso de tener un mes el auto salí a la ruta. (Acá en argentina es muy normal que las rutas sean de un solo carril y doble mano, por lo que hacer un adelantamiento tiene que ser una maniobra muy precisa). Al querer acelerar mi auto a fondo se me cortó la aceleración bruscamente. Perdió la potencia y me encendió la luz amarilla del check engine. Por suerte pude llegar a pasar. Legué a mi casa sorprendido e investigué en las redes. Me encuentro con que la bomba de alta presion de mi vehículo tiene una falla (aparentemente le pasó a mucha gente) Espero que estas quejas lleguen a las autoridades de mercedes benz y se hagan responsables antes de que esta falla provoque un accidente mortal. ENGLISH TRANSLATION: Hello everyone. Three months ago, I bought a 2012 Mercedes-Benz C250 in Argentina. About a month after I had the car, I hit the road. (Here in Argentina, it's very common for roads to be single-lane, two-way, so overtaking requires very precise maneuvering.) When I tried to accelerate my car fully, the acceleration abruptly cut out. I lost power and the yellow check engine light came on. Luckily, I was able to get through. I arrived home, surprised, and I did some research online. I discovered that my vehicle's high-pressure pump was faulty (apparently, it's happened to a lot of people). I hope these complaints reach the Mercedes-Benz authorities and they take responsibility before this fault causes a fatal accident.

NHTSA ID

11655843

Incident

Apr 19, 2025

The contact owns a 2013 Mercedes-Benz C250. The contact stated while driving approximately 50 MPH, there was an abnormal knocking sound and a metal-on-metal grinding sound coming from the vehicle. The contact slowed down and stopped the vehicle. The contact restarted the vehicle and heard the same abnormal sounds coming from the vehicle. The contact stated that there was no warning light illuminated. The contact had the vehicle towed to a local dealer, where it was diagnosed and determined that the camshaft needed to be replaced. The vehicle was not repaired. The manufacturer was informed of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 75,000.

NHTSA ID

11654546

Incident

Mar 3, 2025

Mileage

75,000 mi

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.