2006 Mercedes-Benz C350

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

At 9,000 miles my 2006 Mercedes C350 had to have a fuel pump replaced. It was out of warranty (low miles usage for 5 year old car) so I had to pay $900 for the repair. I could smell fuel everytime I filled the tank and the Mercedes dealer said the pump had to be replaced. I read about a recall of E350 models being recalled for the same reason with the same engine. I asked the dealer about this and they said mine was not part of the recall because it is a C class Mercedes. It has the same engine with the same problem and I think this should be looked into.

NHTSA ID

11455570

Incident

Mar 7, 2022

Fuel flex line from firewall to Fuel rail is leaking at both connections, ie. both ends at the swaged fitting.

NHTSA ID

11419055

Incident

May 30, 2021

ACCORDING TO THE MERCEDES-BENZ M272 AND M273 ENGINE CLASS ACTION LAWSUIT, THESE ENGINES ARE EQUIPPED WITH DEFECTIVE GEARS IN THEIR BALANCE SHAFTS (IN THE CASE OF THE M272 ENGINES) OR WITH DEFECTIVE IDLE GEARS (IN THE CASE OF THE M273 ENGINES) THAT WEAR OUT PREMATURELY, EXCESSIVELY AND WITHOUT WARNING, CAUSING THE VEHICLE TO MALFUNCTION, THE 'CHECK ENGINE LIGHT' TO REMAIN ILLUMINATED, AND THE VEHICLE TO MISFIRE AND/OR STOP DRIVING.

NHTSA ID

11151416

Incident

Feb 21, 2014

WHEN DRIVING MY '06 C350 WITH 48 THOUSAND MILES, YES 48K ON IT, THE TRANSMISSION SEEMS TO GO INTO A SAFE MODE. IT NORMALLY OCCURS WHEN DRIVING AT HIGHWAY SPEEDS AND HAVE TO SLOW DOWN GRADUALLY, THEN UPON ACCELERATION THE TRANSMISSION JUST REVS UP THE RPM WITH NO POWER. I'M AFRAID ME AND MY TWO CHILDREN WILL BE REAR-ENDED DUE TO THE LOSS OF POWER IN THE TRANSMISSION. I THEN TRY TO DRIVE IT TO THE NEXT EXIT, SHUT OFF THE ENGINE AND RESTART. THIS NORMALLY RESETS EVERYTHING TO NORMAL. BUT IT COULD OCCUR AGAIN MINUTES OR HOURS LATER WHICH IS NOW GETTING FRUSTRATING GIVEN THE CAR IS BARELY REACHING 50K MILES. SO THIS HAPPENS INTERMITTENTLY, UNEXPECTEDLY, AND WITH VARYING FREQUENCY. MERCEDES BENZ USA SHOULD HAVE A RECALL ON THIS AS WHEN I CALL THE DEALERSHIP THEY KNOW EXACTLY WHAT HAPPENED AND IT'S A VERY WELL-KNOW DEFECT THAT COSTS A CONSIDERABLE AMOUNT TO REPAIR. THIS CAR STARTED DOING IT AT 40K AND DOES IT OFTEN. I'VE NOTIFIED MY LAWYER BECAUSE I'M AFRAID IT COULD HAPPEN WITH A VEHICLE BEHIND ME AND THUS CAUSE AN UNEXPECTED REAR END IMPACT FROM ANOTHER DRIVER ON THE HIGHWAY.

NHTSA ID

11142425

Incident

Sep 10, 2018

Mileage

43,100 mi

COMPLAINT SUMMARY: IN THIS SETTLEMENT THE PLAINTIFFS ALLEGE THAT MERCEDES PRODUCED CERTAIN VEHICLES EQUIPPED WITH DEFECTIVE GEARS IN THEIR BALANCE SHAFTS (IN THE EVENT OF THE M272 ENGINES) OR WITH DEFECTIVE IDLE GEARS (IN THE CASE OF THE M273 ENGINES). THESE DEFECTIVE GEARS WEAR OUT PREMATURELY, EXCESSIVELY, AND WITHOUT WARNING, CAUSING THE VEHICLE TO MALFUNCTION, THE ?CHECK ENGINE LIGHT? TO REMAIN ILLUMINATED, AND THE VEHICLE TO HAVE SYMPTOMS SUCH AS MISFIRING OR CATASTROPHIC STOPS. CASE NAME: MAJEED SEIFI, ET AL. V. MERCEDES BENZ USA LLC CASE NO. 3:12-CV-05493 U.S. DISTRICT COURT FOR THE NORTHERN DISTRICT OF CALIFORNIA. CONTACT: MERCEDES ENGINE DEFECT SETTLEMENT ADMINISTRATOR P.O. BOX 43351 PROVIDENCE, RI 02940-3351 EMAIL: [email protected] PD: MY VEHICLE HAS THE SAME PROBLEM, WITH DEFECTIVE FACTORY GEAR IN THEIR BALANCE SHAFTS. VEHICLE MAKE MODEL YEAR MERCEDES BENZ C350 2006 VIN: (XXXX) GENERATED AT CNHTSA.GOV 1 / 1 (XXXXXXXX) PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).

NHTSA ID

11133377

Incident

Feb 21, 2014

IN THIS SETTLEMENT THE PLAINTIFFS ALLEGE THAT MERCEDES PRODUCED CERTAIN VEHICLES EQUIPPED WITH DEFECTIVE GEARS IN THEIR BALANCE SHAFTS (IN THE EVENT OF THE M272 ENGINES) OR WITH DEFECTIVE IDLE GEARS (IN THE CASE OF THE M273 ENGINES). THESE DEFECTIVE GEARS WEAR OUT PREMATURELY, EXCESSIVELY, AND WITHOUT WARNING, CAUSING THE VEHICLE TO MALFUNCTION, THE 'CHECK ENGINE LIGHT' TO REMAIN ILLUMINATED, AND THE VEHICLE TO HAVE SYMPTOMS SUCH AS MISFIRING OR CATASTROPHIC STOPS. CASE NAME: MAJEED SEIFI, ET AL. V. MERCEDES BENZ USA LLC CASE NO. 3:12-CV-05493 U.S. DISTRICT COURT FOR THE NORTHERN DISTRICT OF CALIFORNIA. CONTACT: MERCEDES ENGINE DEFECT SETTLEMENT ADMINISTRATOR P.O. BOX 43351 PROVIDENCE, RI 02940-3351 EMAIL: [email protected] MY VEHICLE HAS THE SAME PROBLEM, WITH DEFECTIVE FACTORY GEAR IN THEIR BALANCE SHAFTS.

NHTSA ID

11103620

Incident

Feb 21, 2014

Mileage

72,000 mi

TL* THE CONTACT OWNS A 2006 MERCEDES-BENZ E350. WHILE DRIVING 45 MPH, THE BRAKE PEDAL WAS DEPRESSED, BUT FAILED TO ENGAGE AS IT TRAVELED TO THE FLOORBOARD. THE CONTACT WAS ABLE TO SAFELY COAST THE VEHICLE TO A GAS STATION. THE CONTACT STATED THAT THE CHECK ENGINE WARNING INDICATOR ILLUMINATED WEEKS PRIOR TO THE FAILURE. THE VEHICLE WAS TOWED TO MERCEDES-BENZ OF SAN DIEGO (4750 KEARNY MESA RD, SAN DIEGO, CA) WHERE IT WAS DIAGNOSED THAT THE SBC MODULE MALFUNCTIONED AND NEEDED TO BE REPLACED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 243,000. THE VIN WAS NOT PROVIDED. *TT CONTACT STATES THAT VEHICLE WAS TAKEN TO RIVERSIDE MERCEDES-BENZ TO CHECK WHY THE CHECK ENGINE LIGHT WAS ILLUMINATED AND WAS NEVER TOLD THERE WAS A BRAKE MALFUNCTION. TWO WEEKS LATER BRAKES MALFUNCTIONED. *TT

NHTSA ID

11088839

Incident

Apr 6, 2018

Mileage

243,000 mi

EIS AND ESL GO BAD, CAR WILL NOT START DUE TO STEERING WHEEL LOCKING.

NHTSA ID

11065782

Incident

Jan 24, 2018

Mileage

102,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).