2019 Mercedes-Benz CLS 450

Hybrid issue. Cuts off when driving and have to pull over to start back up. Car says to pull over and let the car run

NHTSA ID

11771592

Incident

Oct 8, 2026

My vehicle steering wheel completely disengaged/malfunctioned when driving home. The steering wheel continuously rotates however there is no shifting of wheels. This is hazardous as I had to brake the car and call roadside assistance. It is currently at the Mercedes dealership and will be inspected tomorrow. The car displayed the following error after the steering malfunctioned: ESP® is malfunctioning Other driving systems and driving safety systems may also malfunction. The brake system continues to operate normally. The braking distance in an emergency braking situation can increase. WARNING: Risk of skidding if ESP® is malfunctioning • Drive on carefully.

NHTSA ID

11751960

Incident

Jul 21, 2026

The contact owns a 2019 Mercedes-Benz CLS450. The contact stated that while driving at an undisclosed speed, the vehicle inadvertently lost motive power. The contact was able to pull over to the shoulder of the roadway, where the failure persisted; however, the contact was able to continue driving to the destination at slow speeds. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the transmission wiring harness. The vehicle was repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V445000 (Electrical System), but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 46,000.

NHTSA ID

11680421

Incident

Aug 13, 2025

Mileage

46,000 mi

The contact owns a 2019 Mercedes-Benz CLS450. The contact stated while reversing, the rearview camera image was black. The dealer was notified of the failure. The vehicle was not diagnosed or repaired. The contact related the failure to NHTSA Campaign Number: 22V232000 (Back Over Prevention); however, the VIN was not included in the recall. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 65,000.

NHTSA ID

11669642

Incident

Apr 27, 2025

Mileage

65,000 mi

I have had 5 tire blow outs on my 2019 CLS 450 Mercedes. I purchased the car in August of 2023 and since that time I have experienced 5 tire blow outs on brand new tires within a 1-year time frame. When I got the tire blow outs all of them were while I was driving in local city traffic. This car uses run flat tires. I am having the tires replaced at Discount Tire stores in California. The tire is the following: BRI Potenza 245/35 R20 95 Y. This incident happened on several dates [XXX, XXX, XXX, XXX, XXX]. I have taken the car to the Mercedes dealership Escondido Mercedes. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11632398

Incident

Nov 19, 2023

I am getting repeated flats in this car after hitting small bumps in the car. Whether I am on the freeway or driving around town. I have hit bumps that will blow out the tire. Here are more complaints from consumers : [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11608756

Incident

May 20, 2024

My car started shaking and after putting it on the computer it was an electrical wiring harness issue. I was told it will be 6 k to replace both harnesses. It’s been 8 months and they just received the part. The service tech told me that these cars have this issue due to the position of the harnesses being to close to the exhaust. It dries out the wiring. I went to the Mercedes forum and found numerous complaints about this issue. Recently I baited the Mercedes of downtown Los Angeles and was advised they received another cls 450 with the same issues as myself and several other owners of the cls 450. I have been getting the run around for months. This should be a recall as even if I pay 6k it will happen again! Please help. I even reached out to BBB and the dealership never responded to them. I’ve been in contact with Mercedes head quarters and was advised to reach out to NHTSA

NHTSA ID

11580697

Incident

Aug 11, 2023

I have had to replace 3 wheels at great cost due to cracks. I believe the wheels are defectively designed. The wheels cannot support the vehicle's weight. The cast iron aluminum wheels together with the low profile run flat tires contribute to a road hazard and dangerous condition. I understand that this problem has been encountered by many, many MBZ owners.

NHTSA ID

11552658

Incident

Oct 1, 2023

Complaint Sporadic warning message in instrument cluster "Engine oil pressure, stop switch off vehicle" (or similar) is shown in red on vehicles with low mileage. Cause Directional control valve may stick. Remedy 1‑ Read off oil level in instrument cluster and correct if necessary. 2‑ Perform approx. 10‑15 engine starts, then clear fault codes. 3‑ Perform road test with vehicle. If fault code reoccurs during road test: Install new directional control valve.

Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic /9G‑TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G‑TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on‑going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: ‑ NAG3 Classic (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG sport model (AMG 43 and AMG 53 with converter, automatic transmission 725.0) ‑ NAG3 Classic ‑ Hybrid (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG 63 (automatic transmission 725.0) ‑ NAG3 MOPF ISG2 (automatic transmission 725.1) ‑ NAG3 MOPF Hybrid (automatic transmission 725.1) ‑ NAG3 MOPF AMG sport model (AMG 53/AMG 53e with ISG48V2 & converter /hybrid, automatic transmission 725.1) ‑ NAG3 MOPF AMG 43/63 with engine 139/177 (automatic transmission 725.1) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. ‑ Ask precise details about the customer complaint and the conditions and context. ‑ Fill out the service reception questionnaire (please see WIS document: OF27.00‑P‑3000‑05A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: 1. Perform quick test 2. Access the transmission control unit via XENTRY Diagnosis 3. Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). 4. The IPR repair instructions are displayed, Carry out the IPR repair instructions without performing any further diagnostic or repair steps. ‑ Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. Invoicing for the guided IPR steps: Operation item 27‑0640 and 0.1 hours Notice regarding warranty: The use of IPR in association with warranty claims is mandatory! If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. ·Tamper‑proof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner ‑ either in digital form or as a hard‑copy printout and also enclose a printout with the damaged part. In this regard, please comply with the country‑specific warranty requirements of the MPC/general distributor.

Complaint Noises in the steering column area when steering. See example file in the attachments area: "MRSM‑Schleifgeräusch_SCCMGrindingNoises. MOV". Cause Under analysis. Remedy Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: ‑ Loosen screws of the MRSM/SCCM and steering wheel, re‑align the MRSM/SCCM, and re‑fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. ‑ If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. ‑ If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. ‑ If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: ‑ When installing the MRSM/SCCM, make sure that no damage occurs! ‑ If the noise is due to the steering wheel (see attachment "Lenkrad‑Schleifgeräusch_SteeringWheel‑GrindingNoises.mp4"), please use LI46.10‑P‑077313. ‑ Only disassemble and mount all component parts in the "straight‑ahead position" (see also WIS). ‑ Please refer to this LI in the "Notes" section of the warranty claim!

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Red coolant warning in instrument cluster. Fault codes U019F00 or U019F87 current/stored in MRG1 control unit. Cause Various causes Remedy Perform guided test for fault code U019F with XENTRY diagnosis. Verify the following connections are clean and tight. Correct any problems and retest pump actuation: ‑12V plug at M75/11 ‑48V plug at M75/11 ‑48V connector X192/4 ‑Connections at 48V fuse box F153/2 ‑Sockets 1,2, and 5 at connector 2 of MRG1 control unit ‑M75/11 circuit 41 ground If actuation and above connections are OK, but resistance between M75/11 and engine block is less than 2 ohms or heat shield touching coolant pump, proceed with below steps. 1‑Modify engine insulation per attached instructions. 2‑Remove engine control module and measure continuity within control unit between connector 2 pin 1 and connector 6 pin 2. 2a‑If open circuit is found, replace engine control unit (MRG1) and perform initial startup. Refer to XENTRY parts information group 54/054 item 300. 3‑Clear faults and verify M75/11 operating normally.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!