2021 Mercedes-Benz E 450

After the car sits for three or more days, brakes locks up. It takes lots of power to get the brakes to release. It’s a safety concern as the car is parked in the garage with not enough room to maneuver. We never had any car which locks the brakes in this manner. Took it to MB dealer and they say it’s the way brakes are designed. A complete nonsense.

NHTSA ID

11470644

Incident

Feb 23, 2022

Mercedes Benz issued a recall (Manufacturer Recall Number 2021060021; NHTSA Recall Number 21V354) in May 2021. The recall affects my vehicle's MBUX multimedia system, most importantly, the backup camera, which may fail while in use if this issue is not remedied. I was advised of the recall by them in July 2021. To date they have failed to remedy this safety recall. I have contacted Mercedes Benz several times (most recently on 03/21/2022) and they are unable or unwilling to provide a date when this safety issue will be remedied.

NHTSA ID

11457978

Incident

May 14, 2021

The contact owns a 2021 Mercedes-Benz E450. The contact stated that the vehicle speed control was always inadvertently activated, which caused the vehicle to decelerate automatically. The failure nearly caused a collision. The dealer was made aware of the failure and referred the contact to the manufacturer. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure and informed the contact that they would call back. The failure mileage was approximately 1,000.

NHTSA ID

11445405

Incident

Apr 9, 2021

Mileage

1,000 mi

The 48 volt battery on this mild hybrid vehicle failed and the car was unable to be started on May 3, 2021, with 196 miles on the odometer, a mere 15 days after delivery. It had to be taken by flatbed to the dealer where ultimately the 48 volt battery was replaced. Then again on June 5, 2021, the car was again unable to be started, with a mere 735 miles on the odometer. Again, the car had to be taken by flatbed to the dealer, where ultimately the 48 volt battery was replaced a second time. While both failures, fortunately, happened while the vehicle was at home, the could have happened on the highway, in the middle of nowhere in bad weather conditions, or anywhere. I have had to cancel a cross-country drive for fear that, once again, the 48 volt battery will fail, leaving us stranded anywhere or, worse yet, in the middle of a highway.

NHTSA ID

11441712

Incident

May 3, 2021

48Volt battery failed after three months and just 3,400 miles. I understand this is a recurring problem with Mercedes. Car had to be towed as the vehicle was totally inoperable due to battery malfunction. It took more than three weeks for Mercedes to provide a replacement battery. From what I have read, there is a strong likelihood that the battery will fail again.

NHTSA ID

11427592

Incident

Jul 3, 2021

I BOUGHT THIS CAR ON 12/12/2021 AND TWO WEEKS AFTER THAT, THE CAR HAD WARNING MESSAGE ON DASHBOARD "COOLANT TOO HOT, STOP THE VEHICLE" ON THE HIGHWAY -NJ TUNPIKE. IT STARTED SLOWING DOWN ON ITS OWN TO BELOW 20MPH, NEARLY KILLED ME WHILE I TRIED TO PULL IT OVER. THEN THE DEALER SERVICE SAID IT HAD DEFECTIVE WATER PUMP. THEN LAST WEEK 4/13/21 - 4 MONTH,ABOUT 2800 MILEGE ON IT, IT WOULDN'T START AT ALL., JUMP START DIDN'T EVEN WORK. SO I WAS STRANDED AGAIN IN THE MIDDLE OF THE NIGHT. IT GOT TOWED AND THEY SAID IT HAD DEFECTIVE BATTERY. SO HOW MANY DEFECTIVE PARTS THIS CAR HAS. IT WILL KEEP BREAKING DOWN AND THREATEN MY LIFE ON THE HIGHWAY WHERE I COMMUTE EVERY DAY IN THE NIGHT TIME. THEY SHOULD TAKE THIS CAR BACK AND REPLACE BUT THE DEALER REFUSED BECAUSE IT HAD PROBLEMS ON DIFFERENT PARTS AND FIXED. BUT THIS VEHICLE IS PIECE OF JUNK AND A RISK TO NOT ONLY MY LIFE BUT ALSO O THER DRIVERS ON THE HIGHWAY BECAUSE IT DOES THINGS ON ITS OWN WAY, I HAD NO CONTROL OVER THE CAR AT ALL.

NHTSA ID

11413260

Incident

Apr 13, 2021

Mileage

2,800 mi

TL* THE CONTACT OWNS A 2021 MERCEDES-BENZ E450. THE CONTACT STATED THAT WHILE STATIONARY, THE INSTRUMENT PANEL DISPLAYED A MESSAGE INDICATING THAT THE VEHICLE HAD CRASHED. AFTER THE MESSAGE WAS DISPLAYED, THE VEHICLE LOSS MOTIVE POWER. THE VEHICLE WAS TOWED TO MERCEDES-BENZ OF FRESNO (7055 N PALM AVE, FRESNO, CA 93650, (559) 438-0300) TO BE DIAGNOSED. THE PRELIMINARY DIAGNOSTIC RESULT INDICATED THAT THE 48 VOLT BATTERY NEEDED TO BE REPLACED. THE VEHICLE WAS STILL AWAITING REPAIR. THE MANUFACTURER WAS NOT INFORMED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 743.*DT

NHTSA ID

11406950

Incident

Apr 5, 2021

Mileage

743 mi

Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic /9G‑TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G‑TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on‑going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: ‑ NAG3 Classic (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG sport model (AMG 43 and AMG 53 with converter, automatic transmission 725.0) ‑ NAG3 Classic ‑ Hybrid (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG 63 (automatic transmission 725.0) ‑ NAG3 MOPF ISG2 (automatic transmission 725.1) ‑ NAG3 MOPF Hybrid (automatic transmission 725.1) ‑ NAG3 MOPF AMG sport model (AMG 53/AMG 53e with ISG48V2 & converter /hybrid, automatic transmission 725.1) ‑ NAG3 MOPF AMG 43/63 with engine 139/177 (automatic transmission 725.1) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. ‑ Ask precise details about the customer complaint and the conditions and context. ‑ Fill out the service reception questionnaire (please see WIS document: OF27.00‑P‑3000‑05A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: 1. Perform quick test 2. Access the transmission control unit via XENTRY Diagnosis 3. Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). 4. The IPR repair instructions are displayed, Carry out the IPR repair instructions without performing any further diagnostic or repair steps. ‑ Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. Invoicing for the guided IPR steps: Operation item 27‑0640 and 0.1 hours Notice regarding warranty: The use of IPR in association with warranty claims is mandatory! If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. ·Tamper‑proof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner ‑ either in digital form or as a hard‑copy printout and also enclose a printout with the damaged part. In this regard, please comply with the country‑specific warranty requirements of the MPC/general distributor.

Complaint Sporadic warning message in instrument cluster "Engine oil pressure, stop switch off vehicle" (or similar) is shown in red on vehicles with low mileage. Cause Directional control valve may stick. Remedy 1‑ Read off oil level in instrument cluster and correct if necessary. 2‑ Perform approx. 10‑15 engine starts, then clear fault codes. 3‑ Perform road test with vehicle. If fault code reoccurs during road test: Install new directional control valve.

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Red coolant warning in instrument cluster. Fault codes U019F00 or U019F87 current/stored in MRG1 control unit. Cause Various causes Remedy Perform guided test for fault code U019F with XENTRY diagnosis. Verify the following connections are clean and tight. Correct any problems and retest pump actuation: ‑12V plug at M75/11 ‑48V plug at M75/11 ‑48V connector X192/4 ‑Connections at 48V fuse box F153/2 ‑Sockets 1,2, and 5 at connector 2 of MRG1 control unit ‑M75/11 circuit 41 ground If actuation and above connections are OK, but resistance between M75/11 and engine block is less than 2 ohms or heat shield touching coolant pump, proceed with below steps. 1‑Modify engine insulation per attached instructions. 2‑Remove engine control module and measure continuity within control unit between connector 2 pin 1 and connector 6 pin 2. 2a‑If open circuit is found, replace engine control unit (MRG1) and perform initial startup. Refer to XENTRY parts information group 54/054 item 300. 3‑Clear faults and verify M75/11 operating normally.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!