2019 Mercedes-Benz GLE 350

SAME ISSUE AS LAST YEAR'S RECALL - REAR SEAT PASSENGERS IN THE AFFECTED VEHICLES MAY NOT BE ABLE TO FASTEN THEIR SEAT BELTS. TRYING TO BUCKLE MY 7 YR OLD SON IN AND SEATBELT WILL NOT LOOSEN TO STRETCH ACROSS HIS BODY. HAS BEEN GOING ON NOW FOR ABOUT A WEEK OR TWO. HTTPS://WWW.NCCONSUMER.ORG/NEWS-ARTICLES/MERCEDES-BENZ-ISSUES-RECALL-FOR-GLC-VEHICLES-WITH-SEAT-BELT-ISSUE.HTML

NHTSA ID

11283107

Incident

Nov 30, 2019

Mileage

1,700 mi

This NCU replaces the prior NCU issued on May 15, 2025, and contains additional MY 2023 and MY 2024 vehicles which are highlighted below. In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (“MBUSA”) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (“MY”) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: •Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (‘MIL’).

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, June 11, 2026. After June 11th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint -Check engine light illuminated. -Engine runs rough. -Poor shifting or jerking when accelerating. -Fault codes stored related to mixture formation, injector quantity adjustment, or misfire. Note: One or more of the above symptoms can occur. It is possible that no fault codes are stored. Cause Leaking valve seat in cylinder head. Remedy -Perform cylinder leakage check as noted in WIS group 01.00. If excessive leakage is found determine if leak is from intake or exhaust valves. -If leakage is found from intake or exhaust valves, remove cylinder head and inspect valve seats. -The complete cylinder head must be replaced if valve seat damage is found. The valve seats can not be reworked. -Engine oil and filter should be changed after the repair. Workshop notes cylinder head repair: 1. The intake rocker arm roller is narrower than the exhaust and they must not be interchanged. Mark the rocker arms so they are reinstalled in their original location. 2. Inspect all parts that are being reused (i.e. camshafts, rocker arms) for signs of wear or damage. See WIS doc AH05.20-P-1000-09SZ for examples of normal and abnormal wear. Replace parts with new if damage or wear is found. 3. Check that all rocker arms are correctly located on the camshaft before installing cylinder head cover. Rotate engine at least 2 times and check that there are no problems with rocker arms. 4. The timing chain tensioner can be reused if it extends fully, has no noticeable problems in prior operation, and no chain drive components were replaced. 5. Care must be taken when removing fuel injectors to prevent damage. See WIS doc AR07.03-P-0004-03MM. 6. Cleanliness must be observed during repair to prevent subsequent complaint or engine damage: • When cleaning engine block surface, ensure oil ports are sealed to prevent debris from entering oil circuit. Refer to SI01.40-P-0010A. • No abrasive materials, sharp-edged tools, or unapproved cleaners should be used on engine block surface. Refer to AR01.00-P-0050-01A. • Any debris from cleaning that has entered the cooling jacket should be removed before assembly of engine. The debris can otherwise cause blockage in the cooling circuit leading to engine overheating. If any of the parts listed below are found damaged or in need of replacement during cylinder head valve‑seat diagnosis or repair, and the vehicle has warranty coverage, they must be claimed on a separate parts‑only line. These items are not covered under the cylinder head warranty extension and cannot be included with the claim. • Camshafts • Camshaft adjustment solenoids • Camshaft positioners • Fuel injectors • Hydraulic valve play compensating elements • Roller rocker arms • Spark plugs • Timing chain • Timing chain guide rails