2018 Mercedes-Benz Metris

See attached document for complaint. I wanted to express my displeasure with the manner in which the above reference recall was conducted. The timeline left many owners with expensive replacement bills for new tires to replace inadequate tires that were installed as OEM on our vans. The message boards tell a story of frustration for a large group of consumers. As you know the recall was originally made in July of 2022. The notice to dealers went out in September of 2022. Mercedes Benz appeared to really drag their feet on a solution to the issue with the first small number of remedies (219 out of 24,359) in the second quarter of 2024. Remedies did not begin in earnest until the beginning of 2025 almost two and half years after the recall was originally published. As the original ti res were inadequate, I was notified in June of 2023 by your Mercedes-Benz of Pleasanton service center that my tires needed to be replaced at a cost of $1,348. Strange that a dealer would be trying to sell me replacement tires on an item under a recall. I decided in October of 2023 at an odometer reading of only 26,708 to go ahead and replace my tires having given up on your slow roll of the recall remedy. I spent $940 on new tires to replace the inadequate tires. Finally in January of 2025 you notified me that you were prepared to replace my tires if necessary. In April of 2025 at an odometer reading of 34,984 your Mercedes-Benz of Palm Springs service center replaced my "newish" tires with the right size tires. Based on message board activity I think there are many disappointed owners who had a similar experience as evidenced by their comments. I just can't believe a safety recall was left open with no remedy for so long at a great expense and waste. I would ask that you reimburse me for the wasted expenditure of $940 I made in October of 2023 while awaiting your delayed recall solution to make this situation right.

NHTSA ID

11700884

Incident

Nov 5, 2025

The contact owns a 2018 Mercedes-Benz Metris. The contact received notification of NHTSA Campaign Number: 22V482000 (TIRES); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts are not available.

NHTSA ID

11626794

Incident

Nov 5, 2024

The contact owns a 2018 Mercedes-Benz Metris. The contact received notification of NHTSA Campaign Number: 22V482000 (TIRES); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

NHTSA ID

11623896

Incident

Oct 15, 2024

The contact owns a 2018 Mercedes-Benz Metris. The contact stated the vehicle had displayed that there were failures with several safety features. The instrument panel had failed to display any information regarding any safety features. The vehicle had been taken to the dealer who had diagnosed that the brake sensors had failed. The brake sensors had been replaced. Approximately, seven months after having the vehicle repaired the instrument panel displayed failed safety features again. The instrument panel also failed to display any information regarding the safety features of the vehicle. The dealer was informed of the failure; however, the vehicle had not been taken to the dealer to be diagnosed or repaired. The manufacturer was informed of the failure and referred the contact to the dealer. The failure mileage was 10,000. The VIN was unavailable.

NHTSA ID

11617174

Incident

Feb 29, 2024

Mileage

10,000 mi

The check engine light came on, with code P052E indicating a positive crankcase ventilation valve failure. Dealer inspection revealed the PCV valve is sticking and recommended a replacement with a $2100 charge. This is a widely experienced problem with this engine in many Mercedes vehicles, suggesting that the cause is a manufacturer defect.

NHTSA ID

11614205

Incident

Sep 3, 2024

No fix for recall that originated in 2022

NHTSA ID

11613165

Incident

Sep 6, 2024

Recall 22V482 pending since Sept 2022, still no repair available. Tires pose a safety risk.

NHTSA ID

11610157

Incident

Sep 1, 2022

The contact owns a 2018 Mercedes-Benz Metris. The contact received notification of NHTSA Campaign Number: 22V482000 (Tires); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.

NHTSA ID

11610003

Incident

Sep 2, 2022

ASSYST PLUS service reminder appears earlier than expected due to vehicle operating conditions Complaint The ASSYST PLUS service reminder appears earlier than expected. The customer or dealer may report that the vehicle did not reach the starting maintenance interval shown in vehicle documentation, option coding, sales literature, or the Owner's Manual. The service reminder may appear significantly earlier than anticipated even though no faults are stored and no malfunction is present in the vehicle. The remaining distance and remaining time continue to decrease normally until the service reminder is displayed. Cause This condition is not caused by a malfunction of ASSYST PLUS. ASSYST PLUS is a dynamic maintenance management system that continuously evaluates vehicle usage and opera-ting conditions to determine maintenance requirements. The starting maintenance interval specified by variant coding represents a maximum interval that may only be achieved under favorable operating conditions. Actual maintenance intervals may be significantly shorter depending on vehicle use. Vehicle operating conditions such as driving conditions, engine load, engine operating conditions, idling, short-trip operation, environmental influences, oil aging, and Diesel Particulate Filter (DPF) regeneration activity may reduce the maintenance interval from its starting value. These conditions may accelerate engine oil aging through increased soot loading, fuel dilution, moisture accumulation, and additional engine operating stress. As a result, the remaining distance and remaining time until the next service may be reduced from the starting maintenance interval. Remedy Do not replace any parts. A due service must be assumed if the maintenance data calculated by ASSYST PLUS indicates that service is required.

Acoustic Warning or message occurring when a closed sliding door is not recognized Complaint Customer may state the warning message or indicator accompanied by acoustic tone alerting the sliding door is ajar when the door is completely closed Cause There are several reasons that lead to the failure occurring: - Mechanical damage through bending when loading and unloading - Worn contact plates --> After detachment of silver plating, the coper plate is corroded - Movement of sliding door/body when driving --> Contact pins do not always make contact with contact plate --> Central locking system fault message in instrument cluster Remedy In a problem case, replace contact switch for vehicles with +T50/+T55/+EL9 or contact plate with A4478201903. Remember to check the fit of the sliding doors and make any necessary adjustments as per AR72.16-S-1023E (447/448) and AR72.16-D-1023TS (907/910). Further valid damage codes: 82326 Contact switch for central locking system on sliding door 82347 Contact plate for central locking system on sliding door 53196 K/Z contact plate for central locking system on sliding door 82645 Contact switch for sliding door

OM642 DPF Filter Cracked or Broken Complaint Vehicle will not start or exhibits noisy exhaust. Check Engine Lamp (CEL) is on. Multiple control unit communication and system faults may be present, including but not limited to: 134800, 134900, 11B300, 11EC00, 15E100, 155700, 162500. Additional events codes may include: 134300, 102200, 163400, 16CE00. In many cases, multiple unrelated faults are stored due to electrical disruption from wiring damage rather than indivi-dual component failure. Cause The DPF filter is cracked, broken, or leaking, allowing hot exhaust gas to escape from the exhaust system. Depending on the location of the break or leak, hot exhaust gas may be directed toward the main wiring harness and/ or the SCR (Selective Catalytic Reduction) dosing valve assembly. This heat exposure can result in: • Internal melting of wiring insulation within the harness • Short to ground conditions and loss of communication between control units • Damage to the dosing valve and/or heated AdBlue line Damage to the wiring harness may not be visible externally, as the outer tape can remain intact while the internal wires are melted and fused together. Remedy Inspect the DPF assembly for cracks, separation, or leakage. Do not proceed with further diagnosis or component replacement until the exhaust leak source has been identified and confirmed. If any damage is found, replace the DPF filter assembly. Based on the location of the failure, inspect all components in the path of the exhaust leak, including the dosing valve assembly and main wiring harness. The wiring harness must be opened in any area exposed to the exhaust leak to visually inspect the individual wires. External inspection alone is not sufficient to determine harness condition. Repair or replace any damaged wiring in accordance with approved repair procedures. Replace any dosing system components that show signs of heat damage. Failure to identify and repair all heat-affected components will result in repeat faults or no-start conditions.

Check engine light on and FC P146264 stored in engine and fuel pump control units Complaint Check engine light active and FC P146264 Temp. and pressure sensor B4/15 is stored in Engine control unit and Fuel pump control unit. Cause Software parameter in Fuel pump control unit. Remedy Update fuel pump control unit (FSCU) to software version A0009024488 A0009030664. Clear fault codes and check for any additional symptoms.

Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns. If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit.

Check engine light illuminated - Fault code current P04D-B79 The crankcase ventilation system is interrupted. Complaint: Check engine light on. Fault code P04DB79 is current in the engine control module (N3/10). Cause: Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for S208 vent line contact switch. Refer to attached photo of connection location. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found.