2008 Mercedes-Benz ML320

Right rear brake light inoperative even with new bulb. Dash warning light shows this light not working .08

NHTSA ID

11610621

Incident

Aug 2, 2024

THE REAR TURN SIGNALS AND BRAKES LIGHTS ARE NOT WORKING PROPERLY, EVEN WITH NEW BULBS AND REPLACEMENT OF THE BULBS BASE CASE THE TURN SIGNAL STILL BLINKING AS IF THE BULB IS BURNED AND THE BRAKE LIGHT DOESN'T WORK SIMULTANEOUSLY IT WORK WHEN THE TURN SIGNAL IS NOT USED. THE CAR WAS TOOK TO THE DEALER SEVERAL TIMES AND THE PROBLEM CONTINUE THE SAME.

NHTSA ID

11455484

Incident

Aug 24, 2018

8/1/2021 accident involving 2008 Mercedes ML320 CDI >recall faulty tow hitch< Mercedes has refused to conduct an investigation and resolve these damages. While injured (both myself and 9 yr old son w/ a heart condition), no serious injuries or fatalities happened during the accident. It resulted in totaling the vehicle and our camper. Recall doc's show that Mercedes of New Orleans completed the recall; however, they either falsified disclosing they did the repair or conduct poor workmanship when repairing the hitch. While driving the hitch broke/cracked resulting the camper flipping over and slamming into the truck. I have photos along w/ consulted w/ certified welder confirming the weld was not properly done. More photos if needed.

NHTSA ID

11431324

Incident

Aug 1, 2021

Tow hitch weld broke resulting in vehicle accident. Interstate wreck, could have killed myself, my 9 yr old and 4 dogs along w/ any other vehicles that could have struck us.

NHTSA ID

11428004

Incident

Aug 1, 2021

WHILE DRIVING THE MERCEDES ML320 AT NIGHT THE VEHICLE SUDDENLY POSTED THE FOLLOWING MESSAGE "BATTERY VOLTAGE IS TOO LOW. PLEASE START THE ENGINE. OTHERWISE, COMAND WILL SHUT OFF IN 3 MINUTES." THE ENGINE WAS RUNNING AT THIS TIME AND THE VEHICLE WAS IN MOTION. A SHORT TIME LATER THE HEADLIGHTS ON THE VEHICLE SUDDENLY WENT OUT. I TURNED ON THE FLASHERS AND THEY ALSO WENT OUT IN A SHORT TIME. THE VEHICLE WAS PARKED AND WOULD NOT RE-START. ABOUT 15 MINUTES WENT BY AND THE VEHICLE WAS STARTED AND FULLY FUNCTIONAL. NO SIGNS OF CODES OR REDUCED LIGHTING PERFORMANCE. ALSO, NO SIGNS OR REDUCED BATTERY PERFOMANCE WAS OBSERVED.

NHTSA ID

11164312

Incident

Dec 30, 2018

Mileage

200,000 mi

TL* THE CONTACT OWNS A 2008 MERCEDES-BENZ ML320. THE CONTACT STATED THAT THE LIFTGATE FAILED TO OPEN. IN ADDITION, THE REAR MIDDLE BRAKE LIGHT FAILED TO ILLUMINATE. THE CONTACT CALLED MERCEDES-BENZ OF FORT LAUDERDALE AT (954) 949-0623 (LOCATED AT 2411 S FEDERAL HWY, FORT LAUDERDALE, FL 33316) AND WAS INFORMED THAT THE VEHICLE WAS NOT INCLUDED IN A RECALL. THE VEHICLE WAS NOT TAKEN TO A DEALER OR AN INDEPENDENT MECHANIC TO DETERMINE THE CAUSE OF THE FAILURE. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURES. THE APPROXIMATE FAILURE MILEAGE WAS 108,000.

NHTSA ID

11067323

Incident

Jan 31, 2018

Mileage

108,000 mi

MY 2008 IS HAVING THE SAME PROBLEM AS THIS 2009. MERCEDES BENZ IS RECALLING 16,130 MY 2009 M-CLASS W164 PASSENGER VEHICLES EQUIPPED WITH THE OPTIONAL POWER LIFT GATE. AS A RESULT OF A FAULTY SEAL AROUND THE REAR TAIL LAMP ASSEMBLY, WATER MAY ENTER THE REAR COMPARTMENT CONTAINING THE SPARE TIRE. WATER CONTAMINATION OF THE CONTROL UNIT FOR THE POWER LIFT GATE CAN RESULT IN DISABLING OF THE POWER LIFT GATE MOTOR. HAZARD:WATER WILL CAUSE A SHORT CIRCUIT WHICH COULD LEAD TO A FIRE. REMEDY:DEALERS WILL REPLACE THE SEAL OF THE REAR TAIL LAMP ASSEMBLY WITH A THICKER ONE AND REPOSITION THE AFFECTED POWER LIFT GATE CONTROL UNIT INSIDE THE CHASSIS. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING APRIL 2009. OWNERS MAY CONTACT MERCEDES-BENZ AT 1-800-367-6372. ADDITIONAL INFO:MERCEDES BENZ RECALL NO. 2009030003.OWNERS MAY ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S

NHTSA ID

11067316

Incident

Feb 1, 2018

Mileage

107,000 mi

TL* THE CONTACT OWNS A 2008 MERCEDES-BENZ ML320. WHILE DRIVING APPROXIMATELY 30 MPH, THE ENGINE STALLED WITHOUT WARNING. THE VEHICLE RESTARTED, BUT THE FAILURE RECURRED TWICE. THE SECOND TIME THE FAILURE RECURRED, THE VEHICLE DID NOT RESTART. THE CONTACT ALSO STATED THAT THE HORN SOUNDED WITHOUT BEING PROMPTED. THE VEHICLE WAS TOWED TO THE CONTACT'S RESIDENCE WHERE IT WAS NOT DIAGNOSED NOR REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 89,000.

NHTSA ID

10850680

Incident

Mar 12, 2016

Mileage

89,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint The sliding sunroof glass panel of the panoramic roof reverses during the closing process, either once or multiple times, without an entrapment (anti‑pinch) event being detected. The concern may occur temporarily or repeatedly during normal closing operation. Cause The automatic reversing function of the panoramic roof is overly sensitive due to parameterization in combination with seal counter‑pressure. This condition can cause the roof to reverse even though no obstruction is present. Remedy Retrofit the vehicle to meet Cleanpoint status “Panoramic sliding sunroof glass panel reverses during closing without a pinch event.” The retrofit includes: • Hardware modification (installation of a cover rail / EPDM lip) • Corresponding software update for the panoramic roof control unit The prescribed retrofit steps must be performed in the specified sequence as outlined in this document. 1) Retrofit the EPDM lip onto the rear edge of the panoramic sliding roof panel: • Clean the underside of the rear edge of the sliding sunroof panel (marking, Figure 1) (e.g., isopropanol). • Subsequently install the cover rail on the underside of the sliding sunroof panel (Figure 2). - Distance from the cover rail to the rear edge of the sliding sunroof panel A = 5 mm - Distance from the cover rail to the right and left edges of the sliding sunroof panel B = 9 mm - Apply firm pressure by hand along the entire bonding surface of the COVER RAIL - The wider flange at the ends of the cover rail (see Figure 3) must point in the direction of travel 2) Submit an XSS Ticket with the following requests to add SA code O75 to the Vehicle Data Card • Enter code "O75" (Oscar 75) in Vehicle Documentation System (Vedok): • Add the following AO text to KG 78: AO code O75 added as specified in LI77.21-P-075806 (Version 7). 3) Install new software from the panoramic roof control unit (TSSR296, A98, PSD) and teach in the anti-pinch protection again: • Connect XENTRY Diagnosis. - always use the current XENTRY Diagnosis software release with all available add-ons. - Strict compliance with the operation steps in XENTRY Diagnosis is absolutely essential! - Ensure adequate power supply to the vehicle's on-board electrical system battery (greater than 12.5 V) using a battery charger. • Commission the panoramic roof control unit - To do this, select "A98 – control module 'panoramic sliding sunroof' → adaptation → commissioning → Commission the control unit." - Then follow user guidance in XENTRY Diagnosis. • Disconnect XENTRY Diagnosis.

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304