2008 Mercedes-Benz ML63

2008 MERCEDES BENZ ML63. CONSUMER STATES PROBLEMS WITH GASOLINE LEAK AND FUEL GAUGE INDICATOR *TGW WHILE DRIVING ON A COLD RAINY DAY, GAS FUMES GRADUALLY FILLED THE PASSENGER COMPARTMENT. THE WINDOWS WERE ROLLED UP AND THE HEATER WAS ON AT THE TIME. SHORTLY AFTER, THE GAS GAUGE INDICATOR BEGAN TO APPROACH EMPTY MUCH FASTER THAN USUAL. ABOUT AN HOUR LATER, WHILE THE VEHICLE WAS PARKED, THE CONSUMER NOTICED GAS FLOWING ON THE GROUND AROUND THE VEHICLE. THE VEHICLE WAS TOWED TO THE DEALERSHIP AND AN INSPECTION REVEALED A RUPTURE IN THE GAS TANK. THE CONSUMER WAS INFORMED SOMETHING SUCH AS A ROAD HAZARD MUST HAVE HIT THE VEHICLE. *JB MB DENIED THE CONSUMERS REQUEST FOR REIMBURSEMENT. UPDATED 06/10/10.*JB

NHTSA ID

10334837

Incident

Apr 4, 2010

Mileage

17,800 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint The sliding sunroof glass panel of the panoramic roof reverses during the closing process, either once or multiple times, without an entrapment (anti‑pinch) event being detected. The concern may occur temporarily or repeatedly during normal closing operation. Cause The automatic reversing function of the panoramic roof is overly sensitive due to parameterization in combination with seal counter‑pressure. This condition can cause the roof to reverse even though no obstruction is present. Remedy Retrofit the vehicle to meet Cleanpoint status “Panoramic sliding sunroof glass panel reverses during closing without a pinch event.” The retrofit includes: • Hardware modification (installation of a cover rail / EPDM lip) • Corresponding software update for the panoramic roof control unit The prescribed retrofit steps must be performed in the specified sequence as outlined in this document. 1) Retrofit the EPDM lip onto the rear edge of the panoramic sliding roof panel: • Clean the underside of the rear edge of the sliding sunroof panel (marking, Figure 1) (e.g., isopropanol). • Subsequently install the cover rail on the underside of the sliding sunroof panel (Figure 2). - Distance from the cover rail to the rear edge of the sliding sunroof panel A = 5 mm - Distance from the cover rail to the right and left edges of the sliding sunroof panel B = 9 mm - Apply firm pressure by hand along the entire bonding surface of the COVER RAIL - The wider flange at the ends of the cover rail (see Figure 3) must point in the direction of travel 2) Submit an XSS Ticket with the following requests to add SA code O75 to the Vehicle Data Card • Enter code "O75" (Oscar 75) in Vehicle Documentation System (Vedok): • Add the following AO text to KG 78: AO code O75 added as specified in LI77.21-P-075806 (Version 7). 3) Install new software from the panoramic roof control unit (TSSR296, A98, PSD) and teach in the anti-pinch protection again: • Connect XENTRY Diagnosis. - always use the current XENTRY Diagnosis software release with all available add-ons. - Strict compliance with the operation steps in XENTRY Diagnosis is absolutely essential! - Ensure adequate power supply to the vehicle's on-board electrical system battery (greater than 12.5 V) using a battery charger. • Commission the panoramic roof control unit - To do this, select "A98 – control module 'panoramic sliding sunroof' → adaptation → commissioning → Commission the control unit." - Then follow user guidance in XENTRY Diagnosis. • Disconnect XENTRY Diagnosis.

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts