2009 Mercury Mariner

On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages

On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that

My vehicle was returned to me following a torque sensor replacement on 4/9/2026 in poor condition (locked steering and a catastrophic gash in the driver-side tire) rendering it undrivable and unsafe. Crossroads Ford of Prince George shop's inspection report claims the tire damage was pre-existing, I have conclusive evidence to the contrary: Virginia State Inspection: My vehicle passed a Virginia state safety inspection on 2/27/2026. Per state law, any tire with a gash or sidewall crack is an automatic failure. This legally certifies the tire was intact immediately prior to their service. Recent Tire Service: I replaced my rear tires at OK Tire and Auto on 3/30/2026. At that time, a full tread and sidewall inspection of my front tires confirmed they were in good condition. The timing of the dealership's communication confirms the damage occurred while in their care: I arrived for my 9:30a appointment around 9:25a. No damage was noted during the initial intake. I was in their facility when I watched a mechanic drive to the other side of the service parking lot without being informed of a "catastrophic" safety issue. I was only notified of the gash at the end of the day when the vehicle was scheduled for return. Their staff now deems the vehicle "unsafe to drive" for their own employees. If this gash were present at 9:30am, it would have been told to me before I left the dealership. The locked steering is a direct result of an improper torque sensor installation (which is the reason why I was dropping my car off to be serviced). My car was in driving condition as I drove it to the dealership for my appointment with no issues. I received a call from advisor Sade Gregory at 11:03 informing me that I would need a steering column now that is on backorder. At 11:13am I received a confirmation for car delivery to me then at 1:06pm confirmation that my car will arrive at my house at 1:15. At 1:20 Sade Gregory says my car can't be delivered now because its unsafe for them.

NHTSA ID

11730562

Incident

Apr 9, 2026

The contact owns a 2009 Mercury Mariner. The contact stated that while driving at undisclosed speeds on several occasions, the steering wheel started shaking abnormally. The contact added that on several occasions while driving at undisclosed speeds, the vehicle lost power steering functionality, but the vehicle regained power steering functionality shortly afterwards. The "Power Steering Assist Fault" message was displayed on one occasion. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 117,900.

NHTSA ID

11721530

Incident

Feb 15, 2026

Mileage

117,900 mi

My steering has been locking while I am driving and causing loss of steering and control of car. I have contacted crossroads dealer and I have not gotten a response as I am now aware there has been a safety recall on this vehicle.

NHTSA ID

11719580

Incident

Dec 5, 2025

The power steering stopped working. A note did appear to let me know it wasn’t working. I took it in to the mechanic and he confirmed the power steering wasn’t working.

NHTSA ID

11714546

Incident

Jan 22, 2026

Drivers rear shock rusted off the wheel well causing wheel to snap and metal frame to hit the ground while I was traveling 40 mph. At this time the other wheels locked up and started squealing causing loss of control of vehicle shooting me across lanes and hitting curbs on both sides. This was heard all the way inside a church and they came running out. If I had not been able to gain control it would have flipped. The vehicle is available for inspection. It has not been reproduced or confirmed by a dealer or independent service other than the tow truck attendant telling me that the car need to be junk because it could not be repaired. The component has not been inspected by the manufacturer, or insurance company as it only has liability insurance. A police officer did show up on seen to direct traffic around vehicle and did see the issue but no report was taken. There was absolutely no indication that this was an issue until a few seconds before it snapped and that was the wheel started to wobble.

NHTSA ID

11674297

Incident

Jul 9, 2025

Vehicle notification stating Power Steering Assist Fault. Power steering locked up on highway going 60 mph while a child was in vehicle and vehicle was extremely hard to get off the highway. Parkway Ford of Pampa, Tx would not honor recall as VIN was not pulling up a recall. But a different auto mechanic repair shop did verify it was a recall.

NHTSA ID

11668925

Incident

Jun 23, 2025

Power steering failure on may 26th and 27th upon start up. Had to disconnect battery terminal to reset torque sensor

NHTSA ID

11663096

Incident

May 26, 2025

The contact owns a 2009 Mercury Mariner. The contact stated that while driving at an undisclosed speed, the contact became aware that the electronic power steering was not functioning properly, requiring an increased effort to maneuver the vehicle. The vehicle returned to normal functionality, but the failure became a regular occurrence. No warning lights were illuminated. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 14V284000 (Steering); but the VIN was not included. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was unknown.

NHTSA ID

11646320

Incident

Mar 2, 2025

Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.

The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB  SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB  SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.

SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.

SOME 2008-2017 FORD/MERCURY/LINCOLN VEHICLES EQUIPPED WITH SYNC MAY GENERATE A VHR THAT IDENTIFIES A CONCERN WITH THE BRAKES AND SUSPENSION CATEGORY INDICATING SERVICE IS REQUIRED DUE TO A BRAKE SYSTEM WARNING LAMP BEING ILLUMINATED. IF THE PARK BRAKE WAS APPLIED WHEN THE VHR WAS GATHERING DATA FROM THE MAJOR VEHICLE SYSTEMS, THE BRAKES AND SUSPENSION MESSAGE WILL BE REPORTED AS THE VHR LOOKS FOR ANY WARNING LAMPS ILLUMINATED IN THE INSTRUMENT CLUSTER. RERUN THE VHR WITH THE ENGINE ON AND VEHICLE IN PARK, AND ENSURE THE PARK BRAKE IS DISENGAGED. IF THE SYNC VHR IS STILL REPORTING A CONCERN TO THE CUSTOMERS SYNC OWNERS ACCOUNT, REFER TO THE APPROPRIATE WORKSHOP MANUAL SECTION FOR DIAGNOSIS BY DTC OR SYMPTOM. STARTING IN 2015 NOT ALL SYNC EQUIPPED VEHICLES SUPPORT VHR, REFER TO THE OWNERS MANUAL FOR VHR OPERATION.