Owner-reported complaints naming the electrical system, filed with NHTSA
Data refreshed
Reports naming the electrical system — wiring, battery, charging, control modules, infotainment and electrical accessories. Every record below is an owner-reported complaint about the 2025 RAM 3500 submitted to NHTSA — not a confirmed defect, not a recall and not a manufacturer bulletin. 23 reports on file name it.
Complaints are reports submitted by owners and drivers to NHTSA. They are not verified and do not establish that a defect exists.
Shown in the owner’s own words, exactly as filed
3 times to date (10,000 miles/8 months) I have failing abs speed sensors. If I stop moving when all lights come on dash the truck is in operational. I cannot shift gears, put in park or turn engine off. Loose traction control, ads, 4wd, stabiltrac, speedometer. All assitive and braking functions. Code U1412. Dealer replaces speed sensors but problem returns.
There have been a couple of instances where the running boards haven’t deployed when the door has been opened. The most recent caused my 10yr old to FALL OUT IF THE TRUCK and get injured. I believe the combination that is causing it is to get in the truck, hit acc and get I’ll all windows down. Then turn off the acc and stay seated in the truck for some time. Then open the door from inside and they don’t deploy…
My ram truck will intermittently have a Christmas tree of warning lights on the instrument cluster, which occur while driving. During these periods, I do not have access to four-wheel-drive, accident avoidance, antilock brakes, etc. If I continue driving the truck for the remainder of the day, the lights will usually go off, but will be stored in the vehicles PCM. the dealership has previously evaluated this and reports that they cannot fix or evaluate the vehicle because there is not an active warning light when I bring it to the dealership. However, when these lights occur, I could be towing a heavy trailer and have no access to the truck safety systems until the lights correct itself. This has occurred more than once. I do not take photos of the lights each time. The photo included is only one of the times. The last time I believe this occurred was on 1/29/2026. Each episode are the exact same warning lights.
The truck had about 7400 miles on it. It gave a warning that the DPF was near full and take it to dealer, about 20 minutes late it said DPF full power reduced. Two days later it cleared that code and began flashing the turn signal intermittently and giving warnings that the trailer brakes were not working, then that the tailgate was down. Shortly after that the instrument cluster went completely blank. I was driving it to the dealer when it ran out of fuel and forced me to stop on the highway. The vehicle has been at the dealer for almost 4 months now. When they replaced the dash cluster it would take too long to start. They replaced multiple modules and I believe three dash clusters before declaring it repaired. I picked it up for a test drive and the frontal collision warning came on intermittently along with a warning that automatic wipers would not work. I took it back. While at the dealership they reported to me that it developed additional issues and would not shift into gear. It is still at the dealership in Pine Bluff AR.
Recall 26V-059 Brake lights and brakes don’t work sometimes. Dealer has no parts. Will not tell me when parts are coming. This is a serious issue and I need it fixed. It should not take this long.
While driving with a trailer after leaving a jobsite in [XXX] , the vehicle experienced a sudden electrical failure while in motion. The instrument cluster/speedometer screen went completely black and the vehicle lights stopped functioning properly while driving at night. During the incident, we lost the speedometer display and visibility from the vehicle lighting system, creating a serious safety hazard while towing a trailer on public roads. Because of the electrical failure, we were forced to pull off on the side of the road to avoid a potentially dangerous situation. After shutting the truck down and waiting approximately one hour, the vehicle was restarted and the systems eventually began functioning again. This vehicle is used regularly for commercial towing and jobsite operations. A sudden loss of instrument display, lighting systems, and electrical functionality while towing creates a major safety concern for both the occupants of the vehicle and surrounding traffic. The failure appeared intermittent because the vehicle resumed operation after sitting for a period of time. However, the incident involved complete loss of critical vehicle display and lighting systems while driving. The vehicle is available for inspection upon request. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
While driving my truck under normal conditions and using the turn signals as expected, I noticed an issue after parking in my driveway. The turn signals began activating automatically without any driver input, alternating from left to right approximately every 5 seconds. The behavior stopped once I manually engaged the turn signal lever. My truck is one year old - Video Link [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2025 Ram 3500. The contact received notification of NHTSA Campaign Number: 25V826000 (ELECTRICAL SYSTEM); and the vehicle was taken to the dealer, where the instrument panel software update was completed; however, the instrument panel became inoperable after the update was completed. The dealer determined that the instrument panel needed to be replaced; however, the part to do the recall repair was not yet available. The dealer informed the contact that the estimated time for availability was May 11, 2026. The vehicle was not yet repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was unavailable.
The contact owns a 2025 Ram 3500. The contact received a recall notification of NHTSA Campaign Number: 26V059000 (Exterior Lighting, Electrical System); however, when the local dealer was contacted, the contact was informed that the manufacturer was shipping a very limited number of parts to dealers for the repair. The manufacturer was contacted, and the contact was informed that the dealer should request an expedited shipment. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was not repaired. The contact had not experienced a failure.
Fue remolcado barrías veces , no arrancaba , se apagaba totalmente , multiples reparaciones , recall sin resolver , pérdida de uso y de confianza
The contact owns a 2025 Ram 3500. The contact received notification of NHTSA Campaign Number: 26V059000 (EXTERIOR LIGHTING, ELECTRICAL SYSTEM). The contact noticed the failure on the drive back after the vehicle was purchased. The contact stated that on a separate occasion, while driving at an undisclosed speed, the brake lights and turn signals failed to function as intended. The contact lived in a rural area and stated that at night it is dark, and the brake lights nor the turn signals were operable. The contact felt that the vehicle was unsafe to drive. The local dealer was contacted, and the contact was informed that the parts for the recall repair were available. However, the parts were allocated to unsold vehicles first, and there was no estimated time for the recall part to be available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and confirmed with the dealer about the part not being available. The contact was informed that the recall part was blocked from manual ordering. The failure mileage was approximately 500.
While driving down the street between 0 and 35 mph, with no load in the truck and no trailer attached, the trailer brake controller quite working completely and a service message appeared. The dealership ended up replacing the trailer brake gain adjustment switch. Had I been towing a trailer at the time, I would have had zero trailer brakes. I've had this message reappear several times since then. I've attached a picture showing both the message on the gauge cluster as well as a scan of the trouble codes at that time.
The 2025 and 2026 dually 3500 Ram trucks with the 12" AAM rear axle are having issues with the rear wheel speed sensors (different sensor for each side). They apparently fail or are not able to properly communicate to the computer. When this happens, the following are disabled: -ABS -Auto Emergency Braking -4x4 -Electronic Stability Control -Cruise Sometimes, the engine won't shut off. The gauge cluster will state it can't detect which position the transmission is in. So, you cannot shift, and you can't shut the truck off, and you can't drive. You are stuck in place with a running engine. Despite Stellantis releasing a new revision of wheel speed sensors (AB revision), they have failed in less than 2,000 miles on my truck. Many, many dually owners are experiencing these failures. I've had this problem occur over half a dozen times. It has been to the dealership to be repaired 3 times so far. After the 2nd time at the dealership, the sensors only last less than 23 miles.
The 2025 and 2026 dually 3500 Ram trucks with the 12" AAM rear axle are having issues with the rear wheel speed sensors (different sensor for each side). They apparently fail or are not able to properly communicate to the computer. When this happens, the following are disabled: -ABS -Auto Emergency Braking -4x4 -Electronic Stability Control -Cruise Sometimes, the engine won't shut off. The gauge cluster will state it can't detect which position the transmission is in. So, you cannot shift, and you can't shut the truck off, and you can't drive. You are stuck in place with a running engine. Despite Stellantis releasing a new revision of wheel speed sensors (AB revision), they have failed in less than 2,000 miles on my truck. Many, many dually owners are experiencing these failures. I've had this problem occur over half a dozen times. It has been to the dealership to be repaired 3 times so far. After the 2nd time at the dealership, the sensors only last less than 23 miles.
The 2025 and 2026 dually 3500 Ram trucks with the 12" AAM rear axle are having issues with the rear wheel speed sensors (different sensor for each side). They apparently fail or are not able to properly communicate to the computer. When this happens, the following are disabled: -ABS -Auto Emergency Braking -4x4 -Electronic Stability Control -Cruise Sometimes, the engine won't shut off. The gauge cluster will state it can't detect which position the transmission is in. So, you cannot shift, and you can't shut the truck off, and you can't drive. You are stuck in place with a running engine. Despite Stellantis releasing a new revision of wheel speed sensors (AB revision), they have failed in less than 2,000 miles on my truck. Many, many dually owners are experiencing these failures. I've had this problem occur over half a dozen times. It has been to the dealership to be repaired 3 times so far. After the 2nd time at the dealership, the sensors only last less than 23 miles.
The 2025 and 2026 dually 3500 Ram trucks with the 12" AAM rear axle are having issues with the rear wheel speed sensors (different sensor for each side). They apparently fail or are not able to properly communicate to the computer. When this happens, the following are disabled: -ABS -Auto Emergency Braking -4x4 -Electronic Stability Control -Cruise Sometimes, the engine won't shut off. The gauge cluster will state it can't detect which position the transmission is in. So, you cannot shift, and you can't shut the truck off, and you can't drive. You are stuck in place with a running engine. Despite Stellantis releasing a new revision of wheel speed sensors (AB revision), they have failed in less than 2,000 miles on my truck. Many, many dually owners are experiencing these failures. I've had this problem occur over half a dozen times. It has been to the dealership to be repaired 3 times so far. After the 2nd time at the dealership, the sensors only last less than 23 miles.
The 2025 and 2026 dually 3500 Ram trucks with the 12" AAM rear axle are having issues with the rear wheel speed sensors (different sensor for each side). They apparently fail or are not able to properly communicate to the computer. When this happens, the following are disabled: -ABS -Auto Emergency Braking -4x4 -Electronic Stability Control -Cruise Sometimes, the engine won't shut off. The gauge cluster will state it can't detect which position the transmission is in. So, you cannot shift, and you can't shut the truck off, and you can't drive. You are stuck in place with a running engine. Despite Stellantis releasing a new revision of wheel speed sensors (AB revision), they have failed in less than 2,000 miles on my truck. Many, many dually owners are experiencing these failures. I've had this problem occur over half a dozen times. It has been to the dealership to be repaired 3 times so far. After the 2nd time at the dealership, the sensors only last less than 23 miles.
On January 14, 2026, while starting my 2025 RAM 3500 with approximately 4,000 miles on the vehicle, the digital instrument cluster completely failed to function. After the engine started and the vehicle was running, the dashboard continued to display “Press Brake and Press Button to Start,” as if the vehicle had not started. All gauges and indicators were inoperative, including the speedometer, tachometer, warning lights, and vehicle information displays. Although the vehicle could be driven and exterior turn signals were functioning, there was no indication on the instrument cluster. No speed, engine RPM, or warning alerts were visible to the driver. After driving the vehicle home and allowing it to sit for a period of time, the vehicle was restarted and the instrument cluster returned to normal operation, indicating an intermittent failure. Based on known issues reported with digital instrument cluster failures, this appears to be a potential electrical and/or software-related defect. In addition to the instrument cluster failure, the vehicle has experienced electrical issues related to trailer lighting. When towing a new trailer equipped with LED lights, the running lights would not function when connected to this truck, although the trailer lighting worked properly when connected to other vehicles. The trailer was taken to the manufacturer’s shop for a full inspection, which confirmed the trailer was functioning properly and identified the truck as the source of the issue. On January 12, 2026, during an oil change service, the trailer lighting issue was reported to the dealership. When the technician connected a diagnostic tester to the truck’s trailer wiring connection, portions of the connection began to smoke. The dealership determined there was a defect in the truck’s electrical system and ordered a replacement component. I have video documentation provided by the dealership technician showing the issue at the trailer light connection.
On 12/15/2015 my 2025 RAM 3500 at 30180 miles had a Trailer communication problem with Running lights on trailer not working. It was sent to RAM dealership in Albany, OR. They diagnosed that the Integrated Trailer control module was at fault. It was replaced and passed working operation, On 12/30/25 Ram was connected to Trailer. The Trailer seemed to be fully operational and about 5 miles down the road the Running lights stoped working again. I had trailed tested and no electrical issues were found. Had 7 way trailer pin in Ram tested and showed 12V power but no out for Running lights. Schedule another appointment to go to Wilson Ram in Corvallis, OR. The ran another diagnostic test on it and found it was fully operational and they could not duplicate the issue I was having. As the Ram gets closer to warranty being expired and I use this Ram for business hauling a trailer that it’s a safety issue when Running lights don’t work. I feel that RAM needs to address this problem sooner than later. I will be getting my Ram back on 01/09/2026 and We’ll connect to Trailer once again and see if itheir is no issues this time. I feel a recall should be in place to resolve the problem with a new harness, brake controller and all modules for Trailer Tow system. As a consumer having down time due to having to go back for diagnostics all parts should be replaced if one part of the system has failed. Is it not only a safety issue it can impact business owners who Need their Vehicle to operate their business. Thank you for taking the time and I will submit follow up if these trailer issues continue.
2025 ram 3500 dual rear wheel truck has intermittent anti lock brake failure . As well as traction control, forward collision warning/assist, lane departure, high beam headlights, and other safety systems. The dealership has tried to fix these issues 8 or more times, with no success. It is illegal for Ram and Stellantis to put customers back into vehicles with anti lock brake failures. In wet/slick/or hard braking situations, loss of anti lock brakes is dangerous to my family as well as other drivers on the roads. And that danger increases when towing a large trailer when the failure happens. The dealership and Stellantis/Ram know of these problems with 2025-26 dual rear wheel Ram pickups.
The contact owns a 2025 Ram 3500. The contact stated that the front passenger's side, rear passenger's side, and driver's side seat belt reminder (SBR) system was inoperable. There was no warning light illuminated. The vehicle was taken to the dealer, where a third-party engineer diagnosed the vehicle and determined that the vehicle was only designed with a front driver's seat belt reminder (SBR). The manufacturer later informed the contact that Ram engineers had confirmed that the vehicle was operating as designed. The vehicle was not repaired. The failure mileage was approximately 18.
Brand new truck (497 miles) while driving on freeway at 70 mph, truck kicked out of cruise control and threw traction control, adaptive cruise control, 4wd, check engine, and anti lock brakes disabled fault lights and codes. The vehicle will disable all these safety features for 30-50 miles, and then the faults will randomly disappear except for the check engine light. This has happened 10-12 times. This truck has had 4-5 “ram cares” case numbers, has been at the dealership for over a month combined. The faulty part supposedly is a right rear wheel speed sensor on the 12” dually axles. There is hundreds if not thousands of these trucks affected. Stellantis/ram says the sensor is has been updated, but is currently not built or for sale., there is a national backorder. We are being told to drive these trucks while ram comes up with a fix. These speed sensors affect systems that have been federally mandated since September of 2012 (anti lock brakes). They are putting customers and other drivers on the road in danger with the intermittent failure of the brakes and traction control in wet conditions.
Ton of warning lights can on like abs, traction control and some other sensors. When put in Drive the D flashed and try k would not move. Put back in park would not recognize it was in park and would not shut off. The only way to shut off the truck with disconnect both batteries and pull the fuse for the fuel pump.
Higher-selling and older vehicles accumulate more reports. Counts are not failure rates and are not directly comparable between vehicles that sold in very different numbers.
Categories with enough reports to have a page of their own
Data on this page last refreshed .