Reports submitted to NHTSA by owners and drivers, shown in full
Data refreshed
Our database holds 206 NHTSA owner-reported complaints for the 2024 Toyota Grand Highlander. Each one is a report filed by an owner or driver and published by NHTSA without most of them being verified. A complaint is not a confirmed defect, not a recall and not a manufacturer bulletin. Narratives are shown exactly as filed.
Complaints are reports submitted by owners and drivers to NHTSA. They are not verified and do not establish that a defect exists.
Showing 1–25 of 206 · page 1 of 9
Vehicle intermittently fails to accelerate when accelerator pedal is depressed after stopping. Vehicle may move extremely slowly for several seconds and then suddenly regain power. This has occurred while entering/intersecting traffic and has resulted in near-collision situations. Dealer cannot duplicate the problem.
I have a 2024 Toyota Grand Highlander (FWD Gas) with about 37,000 miles and had 2 wheel bearings fail - front right and rear right. I noticed a constant humming noise starting around 20-25 mph that increased with vehicle speed. Thinking it was tire noise, I replaced all 4 tires, and the sound was still present. The dealership first replaced the right front bearing, and when they drove it after the repair, they noticed the sound decreased but did not eliminate the noise, and they further diagnosed a failed rear wheel bearing.
My vehicle has a recurrent issue with failing front axle assemblies. The vehicle experienced rotational clicking and had both from axle assemblies replaced around 20,000 miles. Around 40,000 miles the clicking returned and toyota has refused to replace the failing axles again. I currently am at 63,000 miles and I won an arbitration case regarding the axles. The arbitration decision ordered toyota to replace the axles and determined that the parts were defective and covered under warranty. Toyota breached the arbitration and refused to replace the defective axles as ordered in a legally binding arbitration. Rotational clicking is more apparent at low ambient temperatures. A metallic grinding is more apparent at high ambient temperatures. I have had several drive train skips, a sensation of drive train parts slipping and slamming together. Toyota knowingly put defective parts back on my car during the 20,000 mile repair. Toyota release a technical service bulletin T-SB-0082-24 in sep of 2024. It stated that they redesigned the axle to fix the problem. The tsb said to put the original part number on instead of the updated, fixed part number. I received the old, broken part number when my repair was done in 2025. There is a new bulletin T-SB-0028-26 release in april 2026 for the same issue and it states that the previous bulletin is obsolete. The new bulletin states that the correct part number is the new part number not the old one. Additionally, the tsb indicates toyota changed to the new part number with a vin cutoff sometime in 2024. The fixed part number was changed at the production line level in 2024 yet I received the old, known defective part. These are drive axles and a failure can lead to loss of control and a serious accident. A full investigation and recall of this part should be conducted.
The contact owns a 2024 Toyota Grand Highlander. The contact stated that the vehicle unexpectedly lurched forward while depressing the brake pedal. There was no warning light illuminated. The contact stated that excessive pressure was needed on the brake pedal to prevent the failure. The contact stated that a service appointment was scheduled with the dealer. While conducting independent research, the contact identified Technical Service Bulletin: T-SB-0028-25, which was associated with the vehicle shuddering while at a complete stop, and believed that the failure was associated with the technical service bulletin. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 39,000.
The contact owns a 2024 Toyota Grand Highlander. The contact stated that while at a stoplight and attempting to drive forward, while making a left turn, the vehicle experienced a momentary unintended acceleration and lurched forward. The contact immediately depressed the brake pedal to stop the vehicle. The cause of the failure was not yet determined. The local dealer and manufacturer were notified of the failure. The failure mileage was 40,544.
The contact owns a 2024 Toyota Grand Highlander. The contact stated that while driving at an undisclosed speed and turning the steering wheel to the left or the right, occasionally there was a clicking sound coming from the vehicle. The dealer was contacted and diagnosed the failure as an axle failure. The vehicle was repaired, but the failure reoccurred approximately two to three months later. The vehicle was repaired five times due to failures. There was no sound coming from the vehicle after the last repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 5.
The contact owns a 2024 Toyota Grand Highlander. The contact stated that while driving at an undisclosed speed, the vehicle failed to accelerate immediately while the accelerator pedal was depressed. The vehicle then accelerated and lurched forward while entering traffic. There was no warning light illuminated. The vehicle was taken to the dealer; however, the vehicle was not yet diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 18,000.
I own a 2024 Toyota Grand Highlander Platinum Hybrid MAX with approximately 34,000 miles. The vehicle has experienced repeated delayed or absent acceleration from a complete stop, creating a serious risk when entering traffic. Before the most recent repair, I reported intermittent hesitation to the Toyota dealer. On Sunday, July 12, 2026, shortly after startup, the vehicle hesitated twice within the first half mile. At the second stop sign, I attempted a left turn into traffic and applied approximately 30% accelerator pedal. The engine was running, but the vehicle only crept forward at idle-level power for approximately three seconds. There was no noticeable increase in engine RPM and no warning lights. Normal power then returned. On July 15, 2026, the Toyota dealer performed TSB T-SB-0017-24 and updated the engine-control software for hesitation during acceleration. After that repair, the same loss-of-acceleration condition happened again while my wife was leaving a parking lot. She was stopped at a stop sign, making a right turn into traffic on a slight uphill grade, when the vehicle failed to provide normal acceleration. This was substantially similar to the earlier incident and occurred after the software update intended to correct the problem. The repeated failure to respond to accelerator input from a stop creates a collision risk because the vehicle can begin entering traffic without providing the expected power. I am requesting that NHTSA investigate whether this is a broader safety defect affecting the Grand Highlander Hybrid MAX and whether the existing software repair is effective.
I've had consistent issues with the vehicle accelerating and shifting. These include sluggish acceleration, loss of power and sputtering when we've come to a complete stop and starting to move again. We've almost been hit by other vehicles at least over 20 times because the vehicle has failed to accelerate when pulling into a roadway. The car hesitates during acceleration regardless of how much I push the gas. Once it starts to go, it feels as though the car can't shift from 1st to 2nd gear, The RPMs get extremely high while the car is going 25-40 mph and remain there for a few seconds up to ~20 seconds. I am fearful of getting t-boned when my car hesitates while turning at an intersection, going through an intersection or pulling out from a parking lot. I have been stuck in several intersections when traffic was coming toward me, but thankfully those cars had patience and avoided us. I've also found that this issue always happens when the hybrid battery shows that it only has a charge of 3 bars. It seems that the engine, transmission and hybrid battery don't know how to communicate when the battery charge gets that low. This has been happening since Dec 2023 when I bought the vehicle and the dealer has never been able to duplicate or find any error code, they are refusing to fix a known issue when many others are experiencing the same issue. There are Toyota Technical Service Bulletins (TSBs) out there regarding this problem but my dealer told me they won't do anything as it could label my vehicle a lemon. This is creating an unnecessary safety risk for me and my family.
The passenger-side second-row bench seat (60 percent section of the 60/40 split) has a defective seat track/latch assembly that fails in both directions: it seizes completely when it should slide, and it failed to stay latched while the vehicle was in motion. The seat saw almost no use for the first 34 months of ownership (third row kept folded). Within two weeks of its first regular use (XXX, approx. 45,700 miles), it seized completely and could not be moved in either direction. An authorized Toyota dealership in Placerville, CA disassembled the seat and documented in writing that the seat track was twisted and rubbing against the seat frame. The dealer straightened the track rather than replacing it and stated on the invoice that if the seat stopped moving again, both seat tracks should be replaced and the seat frame itself may need replacement or adjustment. After that repair, in approximately mid-June 2026, the bench slid FORWARD on its own as my wife braked for a stoplight, the track failed to remain latched with the vehicle in motion. Two rear-facing infant car seats are installed on this bench, and our toddlers reach the third row through this seat. On XXX (approx. 46,416 miles, 33 days and about 700 miles after the repair), the seat seized again. The vehicle is currently at a second authorized Toyota dealership in [XXX] for diagnosis and is available for inspection upon request. Safety risk: a second-row seat that does not remain latched cannot properly restrain occupants or anchored child restraints during hard braking or a crash, and a seized seat blocks third-row access and egress for children, including in an emergency. There were no warning lamps or prior symptoms before either failure. Note: NHTSA recall 26V128 covers 2021-2024 Highlander second-row seats that fail to lock; this Grand Highlander is not included in that campaign but exhibits a similar failure to remain latched. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
On a recent road trip I experience loss of acceleration twice. I was at a stop sign making a left hand turn. I step on the accelerator it start forward but then stop suddenly leaving me in the 1st lane of on coming traffic. I smashed on the accelerator several time before the vehicle finally responded. I took the vehicle to the dealer on 6/30 told the dealer what had happen along with my google findings acceleration hesitation and sudden lurching in the Toyota Grand Highlander Hybrid MAX Technical Service Bulletins (TSBs), including T-SB-0017-24. The dealer could not duplicate or find any error code, they are refusing to fix a known issue. They are creating an unnecessary safety risk for me and my family.
Driving down the highway and the sunroof exploded
While driving my 2024 Toyota Grand Highlander Hybrid AWD at highway speed with only 16,755 miles on the vehicle, multiple warning messages suddenly appeared, including warnings related to the engine, hybrid system, AWD system, and other vehicle functions. The vehicle instructed me to pull over immediately and significantly reduced power output, making it difficult to maintain highway speed and safely maneuver through traffic. I was able to reach the shoulder and had the vehicle towed to a Toyota dealership. The dealer diagnosed a punctured radiator caused by a rock or similar road debris that allegedly passed through the front grille and struck the radiator. The dealer confirmed that coolant loss from the puncture triggered the vehicle's protective reduced-power mode. This failure created a significant safety risk. A sudden loss of power while traveling at highway speed increases the risk of rear-end collisions and other accidents, particularly in heavy traffic where drivers may not expect a vehicle to rapidly decelerate. There were no warning lights, messages, leaks, drivability concerns, or other symptoms before the incident. All warnings appeared suddenly at the time of failure. Toyota has declined warranty coverage, classifying the damage as a road hazard. However, I believe this may indicate a design defect. I have identified numerous reports from other GH owners describing nearly identical failures involving rocks penetrating the radiator through the front grille, often at relatively low mileage. These reports suggest the radiator may be inadequately protected from ordinary roadway debris. My concern is not simply radiator damage, but that a small piece of road debris encountered during normal driving can disable a critical component and cause the vehicle to enter a severe reduced-power mode at highway speed. I request that NHTSA investigate whether the front grille and radiator protection design of the Grand Highlander creates an unreasonable safety risk
Vehicle: 2024 Toyota Grand Highlander Hybrid Max The vehicle intermittently experiences a severe hesitation and shudder during acceleration from approximately 0-40 mph. The condition occurs only under specific circumstances: -The vehicle has been parked long enough for the engine, transmission, and related systems to cool to ambient air temperature. -The vehicle is started and driven shortly thereafter. -Engine oil and transmission temperatures are below approximately 160°F. -The air conditioning system is operating at maximum cooling with Eco Air Mode enabled. -The hybrid battery indicator displays approximately three bars of charge. When these precise conditions are present, the vehicle may hesitate, shudder, and fail to respond normally to accelerator pedal input during acceleration. Even with the accelerator pedal fully depressed, repeatedly, there is a noticeable delay in power delivery and vehicle acceleration. This creates a situation where the vehicle does not accelerate as expected when entering traffic or attempting to increase speed. The vehicle has previously received Toyota Technical Service Bulletin T-SB-0017-24; however, the condition continues to occur intermittently. No warning lights, diagnostic messages, or system faults are displayed when the event occurs. The condition typically occurs only once during the initial drive cycle after a cold start and has not been observed after the vehicle reaches normal operating temperature. The issue is most common in the warmer months and has never been encountered at freezing or below temperatures.
A couple of days ago, I was driving when my Toyota Grand Highlander started displaying a series of alerts. These alerts included "Hybrid system malfunction" "All Wheel Drive malfunction," "Check engine. See dealer," and finally something akin to "Find a safe place to pull over and turn off vehicle." Until these alerts appeared, back-to-back-to-back, there were no indications that there was anything wrong with the car. We were fortunate enough to be both close to home and close to a dealership when this happened and were able to bring the car in right away. If we were in a high traffic situation, or, conversely, in a very rural area (specifically in winter, not an unlikely happening for us), having the car's drive system suddenly fail out of nowhere could have been very dangerous. As I said, we were able to get the car to the dealer soon after. The dealership informed us that the car has a coolant system perforation, more than likely from a rock penetrating the grill. The coolant than leaked, causing the hybrid system/other failures the car noted. I have since done some research on this issue and have found, to my dismay and disappointment, that this isn't an uncommon issue with the Grand Highlander and the Highlander. There are many instances of people on social media saying a similar issue happened with their cars - one other person's dealership quoted them the exact same amount of the repair that our dealership did. In fact, this is such a common issue that there is apparently already an established workaround: other owners have ordered aluminum mesh from third party vendors and have zip-tied it to their grills in order to keep the rocks out. This is an absurd thing to have to do. Consumers should not, in the year 2026, have to drive down the road with concern that a loose pebble will put their car out of commission. Cars should be able to withstand this very common occurrence without taking substantial damage. This seems like a design flaw.
What component or system failed or malfunctioned, and is it available for inspection upon request? I was driving when I heard a loud boom, it almost sounded like a gunshot. Not noticing anything I continued driving. After a short distance I started hearing wind whistling. It was at this point I pulled over and saw my sunroof had shattered and there was a big hole. How was your safety or the safety of others put at risk? If I had not have the shade closed glass would have fallen into the car. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes, I brought the car to the Toyota dealership. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? I did call my insurance company but I am not sure if they actually inspected the damage. They have been dealing directly with the Toyota dealership service department. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? No, that's why I continued to drive until I heard the wind whistling
My 2024 Used Toyota Grand Highlander Hybrid Platinum Max was at a slight decline stopped at a stop sign in Echo mode. The whole car began to violently shake and lurching forward. No one was in front of me and my foot was on the brake or I probably would have run into a car in front of me. The dashboard then flashed a warning about the hybrid system overheating. The only way to stop it was to turn off the engine, then turn it back on. The car then began driving normally. I have also had an issue with hesitation felt while accelerating 0-40 mph with study throttle. Upon researching both issues, they should be resolved with TSB calibrations to my car of T-SB-0028-25 and T-SB-0017-24. This is not an error that would come up when doing a diagnostic check on my car's computer per research I have done. I took my car to get the updates at Toyota of Redlands, CA, and they refused to do them unless they could recreate them themselves. I called Toyota to report this, and they said that each Toyota dealership/service is privately owned at their own discretion. I was basically told to return if I experience it again. I do not want to experience this again and they wouldn't take my word on it anyways. I feel like next time I could injure myself or someone else if this glitch happened again. I therefore would like to implore to make this a mandatory preventative TSB calibration for cars that have had this reported/models/year which mine has. This goes for any TSB calibrations should be done preventatively, but especially ones that can cause a potential accident like T-SB-0028-25 and T-SB-0017-24. Here is information on why this would not show up on a diagnostic test: Your Toyota didn't generate an error code because the shudder is a software calibration issue rather than a component failure. The onboard computer (ECU) only triggers a check engine light or throws a Diagnostic Trouble Code (DTC) when sensors detect a hard mechanical or electrical failure.
On [XXX], while driving my 2024 Toyota Grand Highlander at approximately 45-50 mph on a gusty, high-wind day, the rear panoramic moonroof/sunroof panel blew out and shattered completely without warning. The failure occurred as I rolled up the vehicle windows during the wind gust. Rapid window closure created a sudden spike in cabin air pressure — a documented pressure differential mechanism — that forced the moonroof glass outward until it shattered. There was no external impact of any kind. The glass, which is not laminated safety glass, scattered throughout the interior with occupants present. Component is available for inspection. This failure is consistent with NHTSA Investigation PE13-035 (Kia Sorento panoramic sunroof spontaneous breakage), in which ODI found glass shattering while in motion to be a safety hazard warranting engineering analysis. The same pressure-based failure mechanism applies here. This is a documented pattern on this specific model. Lemberg Law [XXX] ) analysis of NHTSA complaint data confirms spontaneous sunroof shattering among the top defects on both 2024 and 2025 Grand Highlanders, with Toyota denying warranty claims by alleging "outside influence" — disputed by owners and attorneys alike. No recall currently exists for this component. The rear seat directly below this glass is a primary location for child safety seats. Non-laminated glass shattering over rear occupants — including infants — represents an acute and unacceptable injury risk. I request NHTSA open a formal defect investigation into the panoramic moonroof/sunroof glass on 2024-2025 Toyota Grand Highlanders and evaluate whether a safety recall is warranted. I have photographs and have notified Toyota Motor North America in writing. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
3rd row seats do not want to lock into position, there is also broken plastic pieces from the locking mechanism area. Seats do not want to engage or disengage when trying to lay them flat. This had been a reported problem on other highlanders. This has been an issue since we purchased the vehicle in 2024. This is a safety issue because I fear they would fail in a crash.
It was noted that the drivers door weather strip deteriorated even though the car is less than 3 years old/ 47,000 miles. The dealer and the Toyota customer care said it is likely related to external factors and not covered under warranty. I keep the car in a garage. We have had other cars that are well over 10 years old but do/did not have this problem. This can potentially lead to damage of other components. I see on the internet that other owners of this car have encountered this same issue . There have been 3 safety recalls on this model, related to air bag, instrument panel and rear view camera. These have been fixed. There have been at least 5 Toyota technical service bulletins ( TSBs) published on this model. These were fixed after I brought it up with the dealer/ manufacturer. I was not contacted by the manufacturer proactively. TSB 0017-24 : hesitation felt while accelerating from stop. A software update was performed. TSB 0060-25 : Fuel level logic enhancement. A software update was made. TSB 0028-25 : Shudder sensation at stop. A software update was performed. T-SB-0082-24: CV axle issue: it was fixed T-SB-0111-24: vibrating hood.I notice the issue but did not fix it since the fix involves placing a foam under the hood, which may not fix the underlying issue and might cause other issues. I believe these issues are related to the manufacturing oversight and especially more frequent because it is a first year model .
The rotors started warping around 8K miles
While traveling at highway speed on I-75 northbound, the vehicle experienced a complete and total loss of electrical power. and propulsion. The following conditions were present simultaneously: - Complete loss of propulsion - Inability to shift transmission to neutral — vehicle could not be moved out of the active traffic lane - Complete loss of hazard lights — no ability to warn approaching traffic - Vehicle remained stranded in active highway traffic for approximately 15 minutes - Electrical power spontaneously restored after approximately 15 minutes - Vehicle was then driven off the interstate under its own power That was a life-threatening event. My wife and I could have been struck from behind by highway traffic with no warning lights, no ability to move the vehicle, and no way to signal distress. DEALER VISIT 1 — SATURDAY, APRIL 26, 2026 Dealer: Sarasota Toyota, Sarasota, Florida Complaint presented: Complete electrical shutdown on I-75 the previous day as described above Action taken by dealer: Performed recall repair for black screen issue Outcome: Vehicle returned to customer same day Post-repair symptom: Low voltage warning appeared on drive home from Sarasota Toyota Saturday afternoon Note: Dealer did not perform full electrical diagnostic. Dealer did not flag battery failure. Dealer did not retain vehicle for further investigation despite being informed of complete highway electrical shutdown the previous day. DEALER VISIT 2 — MONDAY, APRIL 28, 2026 Dealer: Germain Toyota of Naples, Naples, Florida Complaint presented: Complete electrical failure on I-75, low voltage warning after Sarasota repair, battery failure Findings: Battery confirmed dead. Alternator confirmed functioning normally. Dealer assessment: Condition described as unusual. Case escalated to Toyota Field Technical Specialist. Current status: Vehicle retained at Germain Toyota of Naples. Rental vehicle provided to customer.
There is an ongoing problem with Android connectivity. I have brought this to the dealer’s attention multiple times, but they continue to claim that my phone is not compatible. However, this same phone connects flawlessly and consistently in my other vehicles, so compatibility does not appear to be the issue.
The vehicle hesitates and does not accelerate immediately from a complete stop. This occurs more frequently when the car is on a slight incline. The delay in acceleration creates a safety concern, especially when attempting to merge into traffic or pull out onto a roadway. I have reported this issue to the dealership multiple times, but they have not taken action because they have been unable to reproduce the problem.
Front brakes were worn prematurely and rotors had to be resurfaced multiple times under warranty and once more after warranty. Premature wear would cause shaking in the steering wheel when medium to heavy braking force was applied.
Higher-selling and older vehicles accumulate more reports. Counts are not failure rates and are not directly comparable between vehicles that sold in very different numbers.
Categories with enough reports to have a page of their own
Data on this page last refreshed .