2004 Toyota MR2

Within the first two weeks after purchasing the vehicle, I noticed a transmission issue where the vehicle would not properly shift gears. I sometimes would try to up or downshift but there would be no change in the display on the gear indicator. Later there became an issue where the vehicle would put itself into neutral while I was in gear and driving, which would cause the vehicle to stop completely in traffic, putting myself and other drivers in the vicinity at risk. This became more and more frequent, and the vehicle even got to the point where it would not shift beyond 2nd gear and was essentially inoperable. After taking the vehicle to Toyota, it was explained to me that they would not be able to repair the vehicle as one of the faulty parts has been discontinued, and advised that I get my money back on the car. The Toyota mechanic further explained that even if the part was replaced, the vehicle may continue to experience the same issue. The dealership that I purchased the vehicle from was unwilling to refund me, but did hold my vehicle for repairs for over 2 months. The vehicle seemed to drive normally for about 1,000 miles after that, but then the same issue repeated. It started again with not shifting gears correctly; there was an instance I was driving on the highway and tried to shift from 5th to 6th but it would not allow me to. In another instance, I was again driving on the highway when the vehicle randomly put itself into 2nd gear and jolted forward, this was followed by a loud revving before the transmission gave out completely and the car would not move. After this, I had the vehicle towed to my residence, as this could have ended in tragedy had the surrounding drivers not been as vigilant. I’ve reported the issue again to the dealership, but they will not take this vehicle back. The car has remained parked outside my residence for well over a month, as it is unfit to be driven on the road.

NHTSA ID

11677560

Incident

Nov 30, 2024

TL* THE CONTACT OWNS A 2004 TOYOTA MR2 SPIDER. THE CONTACT STATED THAT THE CHECK TRANSMISSION LIGHT ILLUMINATED ON THE INSTRUMENT PANEL. WHENEVER THIS OCCURRED, THE VEHICLE BECAME DIFFICULT OR IMPOSSIBLE TO SHIFT GEARS. AN AUTHORIZED DEALER INSPECTED THE VEHICLE AND STATED THAT THE CODES TO THE TRANSMISSION MODULE NEEDED TO BE REPLACED. THE FAILURE MILEAGE WAS UNKNOWN AND THE CURRENT MILEAGE WAS 32,000. UPDATED 04/10/12*LJ THE CONSUMER STATED OVER A YEAR AGO, THE VEHICLE STARTED STALLING AFTER ABOUT 50 MILES. THE EVENT BECAME MORE AND MORE FREQUENT, AFTER A SHORT 50 MILE DRIVE. WHEN HE STOPPED, THE MOTOR WOULD RE-START, BUT THE SEQUENTIAL TRANSMISSION WOULD NOT RESPOND UNTIL THE VEHICLE WAS TURNED OFF FOR ABOUT 30 SECONDS. ON ONE OCCASION, THE TRANSMISSION BECAME STUCK IN 2ND GEAR. UPDATED 04/13/12

NHTSA ID

10446162

Incident

Dec 21, 2010

To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.