2022 Toyota Tundra Problems

This is a follow-up to my NHTSA complaint tracking #11742382, filed June 5, 2026, before my recall repair. I'm filing again because the repair is now complete and it has raised two new concerns: undocumented warranty coverage on the replacement engine, and an unresolved question about whether a second, broader recall applies to that replacement engine. 1. Recall repair completed. Under NHTSA Campaign 24V381000 (Toyota internal 24TA07, filed 2024-05-30), my original engine was replaced with a new OEM assembly (part 04004-23370, serial [XXX], 2026 manufacture date, incorporating the post-April-2024 revised bearing design) at Teton Toyota, Idaho Falls, ID, June 19 to 22, 2026 (repair order [XXX], mileage in/out 28,252/28,281). Toyota's own recall record states the replacement unit was inspected clean. I have no reason to doubt that specific finding; my concern is what happens after. 2. Replacement engine's warranty terms were left undocumented. The repair order lists the warranty "Policy Number" covering the new engine as TBD. As of this filing, Toyota National (1-800-331-4331) has not given me a written answer to a direct question: does the replacement engine carry a new 5-year/60,000-mile powertrain warranty starting from the June 22, 2026 install date, or only the remainder of my original factory warranty? A safety recall remedy that leaves the owner without documented knowledge of what protection they actually received is, in my view, an incomplete remedy under 49 CFR Part 573's recordkeeping and notification requirements. Owners should not have to chase this down themselves months after the repair. 3. A second, broader recall may or may not apply to my replacement engine, and Toyota has not said which. NHTSA Campaign 25V767000 (Toyota internal 25TA14, filed 2025-11-06) expands the same underlying defect population to additional 2022-2024 Tundra, Lexus LX, and 2024 Lexus GX vehicles, with a remedy of inspecting the #1 main bearing via inspection software and INFORMATION REDACTED PURSUANT TO THE FREEDOM OF I

REPEATED CATASTROPHIC ENGINE FAILURE / FAILED RECALL REMEDY. My 2022 Toyota Tundra suffered a complete engine seizure and sudden loss of motive power August 30, 2026, creating an immediate traffic hazard. This is the SECOND time this vehicle has experienced a catastrophic main bearing failure of its twin-turbo V6 engine. The original factory engine was replaced by an authorized Toyota dealership under Safety Recall 24V-381 / 24TA07 in March 2025. The defect should have been resolved. However, the replacement crate engine provided by Toyota carried the exact same engineering vulnerability as the original engine. It was manufactured prior to Toyota's mid-2026 engineering revision, which finally introduced a redesigned #1 main bearing to address localized crankshaft pressure stack-up (as noted in subsequent NHTSA filings like 26V-320).Furthermore, the previous engine replacement due to a federal safety recall was entirely withheld and not disclosed to me at the point of sale. Because Toyota replaced a recalled, defective engine with an identically flawed engine block, the initial recall remedy completely failed, leaving the vehicle dangerous and prone to repeated mechanical failure. The vehicle has driven approximately 16 months since the March 2025 replacement. I am demanding that Toyota provide a permanent remedy using the updated, structurally revised 2026 engine components. It is at the Toyota dealer.

On September 1, 2026, my 2022 Toyota Tundra experienced a serious loss of accelerator response while I was leaving a gas station and entering traffic. I pressed the accelerator, but the truck provided effectively no acceleration, leaving me partially in the roadway. An approaching vehicle had to swerve into the opposing traffic lane to avoid a collision. I had experienced a similar low-speed loss of accelerator response within the prior two weeks. On September 2, while traveling on I-70 at approximately 70 mph, the truck experienced a separate loss-of-power event. Engine RPM dropped considerably and the vehicle felt as though it were coasting. I pressed the accelerator firmly, but it did not respond normally for approximately 5-10 seconds before power returned. Radar/adaptive cruise control was not engaged. I immediately took the truck to Western Slope Toyota. Technicians checked for codes, performed multiple road tests and recorded vehicle data but could not reproduce the intermittent failure. The issue was escalated to Toyota technical assistance under TAS Case 262460664. This problem has been documented by Western Slope Toyota since 2023. Toyota's applicable TSB repairs were performed on prior occasions in an attempt to correct the throttle/hesitation problem, but they did not resolve it. In 2025, the dealer again documented the condition after the earlier TSB had already been performed. According to the September 2026 repair documentation and my discussion with the Western Slope Toyota service manager, Toyota's specialist technical team is aware that the condition can remain despite the TSB work. The repair order states that Toyota identified a known hesitation concern that remains under investigation and that there was no repair to be made at that time. The condition is intermittent and unpredictable and can cause loss of accelerator response or motive power at low and highway speeds. I believe it creates a serious crash risk. Current mileage: 58,735.

Manufacturer Recall Number25TB06 NHTSA Recall Number25V322 In regards to the above mentioned recalls. The vehicle's reverse camera began flashing while driving forward. The R light on the gearshift was also flashing. While driving forward about 15 mph out of a parking lot, the vehicle suddenly went into reverse on it's own, locked up and would not move. I had to have the vehicle towed to the dealership. This happened around the week of June 8. The dealership says that they reset the electrical recall, we picked up the truck and it ran fine for about a week. The reverse camera and R light on the gearshift began flashing again on June 17. It did not shift itself into reverse, but the dealership requested that we bring the vehicle back. The dealership stated that Toyota has "grounded" the vehicle and does not have a fix for the recall to date and continuing to drive it is a safety hazzard. It has been sitting at the dealership since June 18 with no end in sight. The dealership and Toyota Corporate continues to tell me every few days that they do not have a fix for the issues/recalls.

On September 1, 2026, my 2022 Toyota Tundra experienced a serious loss of accelerator response while I was leaving a gas station and entering traffic. I pressed the accelerator, but the truck provided effectively no acceleration, leaving me partially in the roadway. An approaching vehicle had to swerve into the opposing traffic lane to avoid a collision. I had experienced a similar low-speed loss of accelerator response within the prior two weeks. On September 2, while traveling on I-70 at approximately 70 mph, the truck experienced a separate loss-of-power event. Engine RPM dropped considerably and the vehicle felt as though it were coasting. I pressed the accelerator firmly, but it did not respond normally for approximately 5-10 seconds before power returned. Radar/adaptive cruise control was not engaged. I immediately took the truck to Western Slope Toyota. Technicians checked for codes, performed multiple road tests and recorded vehicle data but could not reproduce the intermittent failure. The issue was escalated to Toyota technical assistance under TAS Case 262460664. This problem has been documented by Western Slope Toyota since 2023. Toyota's applicable TSB repairs were performed on prior occasions in an attempt to correct the throttle/hesitation problem, but they did not resolve it. In 2025, the dealer again documented the condition after the earlier TSB had already been performed. According to the September 2026 repair documentation and my discussion with the Western Slope Toyota service manager, Toyota's specialist technical team is aware that the condition can remain despite the TSB work. The repair order states that Toyota identified a known hesitation concern that remains under investigation and that there was no repair to be made at that time. The condition is intermittent and unpredictable and can cause loss of accelerator response or motive power at low and highway speeds. I believe it creates a serious crash risk. Current mileage: 58,735.

Driving on the interstate and the truck surged very hard. The truck began to surge very hard and went into decreased speed mode. We were told by the dealer there is a TSB for the PCM. This decreased power caused the truck to not be able to travel over 25 MPH in a 70 MPH zone. This caused an unsafe situation.

On September 1, 2026, my 2022 Toyota Tundra experienced a serious loss of accelerator response while I was leaving a gas station and entering traffic. I pressed the accelerator, but the truck provided effectively no acceleration, leaving me partially in the roadway. An approaching vehicle had to swerve into the opposing traffic lane to avoid a collision. I had experienced a similar low-speed loss of accelerator response within the prior two weeks. On September 2, while traveling on I-70 at approximately 70 mph, the truck experienced a separate loss-of-power event. Engine RPM dropped considerably and the vehicle felt as though it were coasting. I pressed the accelerator firmly, but it did not respond normally for approximately 5-10 seconds before power returned. Radar/adaptive cruise control was not engaged. I immediately took the truck to Western Slope Toyota. Technicians checked for codes, performed multiple road tests and recorded vehicle data but could not reproduce the intermittent failure. The issue was escalated to Toyota technical assistance under TAS Case 262460664. This problem has been documented by Western Slope Toyota since 2023. Toyota's applicable TSB repairs were performed on prior occasions in an attempt to correct the throttle/hesitation problem, but they did not resolve it. In 2025, the dealer again documented the condition after the earlier TSB had already been performed. According to the September 2026 repair documentation and my discussion with the Western Slope Toyota service manager, Toyota's specialist technical team is aware that the condition can remain despite the TSB work. The repair order states that Toyota identified a known hesitation concern that remains under investigation and that there was no repair to be made at that time. The condition is intermittent and unpredictable and can cause loss of accelerator response or motive power at low and highway speeds. I believe it creates a serious crash risk. Current mileage: 58,735.

I am 99% sure my vehicle is compromised via a cybersecurity incident. My emergency brake will sometimes slam for no reason, no multi media system updates have occurred for over two years, and the vehicle will randomly beep on its own, unlocking the doors. Another major issue is a recent electric harness failure that the mechanics have no idea how it happened. It cost me over 8,000. Warning lights also turn on for no apparent reason such as parking, sensors, and other traction control. I am extremely concerned with my safety. I also believe the odometer has been altered to register higher mileage.

The regain from brake for the hybrid system jerking when go to full stop

The contact called on behalf of the owner of a 2022 Toyota Tundra. The owner received notifications of NHTSA Campaign Numbers: 22V501000 (ELECTRICAL SYSTEM, BACK OVER PREVENTION), 22V661000 (SERVICE BRAKES, HYDRAULIC), 23V142000 (STRUCTURE), 23V566000 (FUEL SYSTEM, GASOLINE), 24V125000 (POWER TRAIN), 24V381000 (ENGINE AND ENGINE COOLING), 25V657000 (BACK OVER PREVENTION), and 25V322000 (EXTERIOR LIGHTING). However, the part to do the exterior lighting recall repair was not yet available. The contact stated that the electronic parking brake failed to function as intended. The contact stated that there are no local dealers on the island in Alaska where the owner resides. The nearest Toyota dealer was 750 miles away and was in Washington State. The manufacturer was contacted and refused to cover the cost to transport the vehicle to Washington State. The failure mileage was approximately 60,000.

The contact's husband owns a 2022 Toyota Tundra. The contact stated that the key fob failed to unlock the front driver’s side door. Due to the failure, the contact was forced to lock the front driver’s side door manually after exiting the vehicle. The contact was forced to enter the vehicle through the front passenger’s side door and crawl over to the front driver side seat. The vehicle was taken to the dealer, and an estimate was provided for the repair. The vehicle was not repaired. The failure mileage was approximately 75,000.

I am 99% sure my vehicle is compromised via a cybersecurity incident. My emergency brake will sometimes slam for no reason, no multi media system updates have occurred for over two years, and the vehicle will randomly beep on its own, unlocking the doors. Another major issue is a recent electric harness failure that the mechanics have no idea how it happened. It cost me over 8,000. Warning lights also turn on for no apparent reason such as parking, sensors, and other traction control. I am extremely concerned with my safety. I also believe the odometer has been altered to register higher mileage.

Water is leaking into the cab of my 2022 Toyota Tundra Platinum 4x4 through the high-mounted third brake light. The leak allows water to enter the headliner and interior, creating the potential for mold, damage to the interior, and electrical issues. After troubleshooting, the third brake light gasket appears to be the source of the leak. Toyota does not appear to offer the gasket as a replacement part, requiring owners to replace the entire third brake light assembly despite the failure being limited to the seal. Numerous owners have reported similar water intrusion issues on 2022+ Tundras, suggesting this may be a common defect rather than an isolated incident. I believe Toyota should investigate the failed gasket design and consider a recall or service campaign to replace the defective seal or assembly.

The contact owns a 2022 Toyota Tundra. The contact stated that while the vehicle was parked, the contact became aware that the rear bumper had detached. The contact stated that the vehicle was previously associated with a recall related to the failure. The vehicle was taken to the dealer, where it was determined that the rear bumper had failed and needed to be replaced. The contact was informed by the dealer that parts were not available and were on backorder. The vehicle was not repaired. The vehicle was taken to another deale,r where the same information was provided, and the contact was informed that the rear bumper needed to be replaced. The vehicle was repaired; however, the failure recurred. The vehicle was taken back to the dealer, where the contact was informed that the rear bumper had failed again and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The approximate failure mileage was 49,150.

The contact's husband owns a 2022 Toyota Tundra. The contact stated that the key fob failed to unlock the front driver’s side door. Due to the failure, the contact was forced to lock the front driver’s side door manually after exiting the vehicle. The contact was forced to enter the vehicle through the front passenger’s side door and crawl over to the front driver side seat. The vehicle was taken to the dealer, and an estimate was provided for the repair. The vehicle was not repaired. The failure mileage was approximately 75,000.

Front seat driver side shield cover has cracked in multiple places and may affect performance of side air bag deployment.

This 2022 Toyota Tundra TRD Pro is subject to Limited Service Campaign 24TD01 for premature tire wear, caused by a factory front toe/camber angle defect acknowledged by Toyota. The vehicle received the campaign remedy (front alignment adjustment and tire replacement) in May 2024, but the same wear pattern on the front tires reappeared and has continued for over a year, documented across multiple dealership visits. A dealership technician found abnormal front tire wear on three separate occasions (August 2025, September 2025, and March 2026) but never recommended a front-end alignment despite Toyota's own campaign identifying alignment/camber as the root cause. As of August 2026, the right front tire tread had worn down to approximately 1/32 inch, an unsafe condition, and only then was an alignment finally recommended in writing for the first time. The vehicle also had a documented brake rotor warping issue (front rotors) as early as November 2024, causing a braking vibration above 40 mph that has persisted. The recurring tire wear presents an ongoing safety risk due to reduced traction and control, particularly relevant given the near-bald tire condition reached before any alignment correction was recommended by the servicing dealer.

The vehicle was purchased brand new from an authorized franchised dealership, sold and contracted as being equipped with a dealer-installed 2.5-inch suspension lift. At approximately 20,000 miles, a severe front-end squeaking symptom developed. The vehicle was brought to a separate authorized Toyota dealership service center for inspection. An authorized Toyota Master Technician formally inspected the vehicle and documented that the selling dealership did not install an engineered suspension lift. Instead, they installed unauthorized, budget aftermarket spacer pucks and non-certified upper control arms. The Master Technician documented in writing that the vehicle "isn't even lifted properly" and a factory front strut has failed prematurely. SAFETY RISK: The unauthorized spacer modification has severely altered and compromised the factory steering and suspension geometry. Because the front suspension, upper control arms, ball joints, struts, and steering rack are forced to operate continuously at unsafe, extreme, out-of-spec angles, the components are subjected to premature, destructive stress. The Master Technician confirmed that this improper configuration creates an imminent highway life-safety hazard, presenting an extreme risk of the front CV axles binding or snapping at highway speeds, which would result in an immediate, catastrophic loss of steering control. The vehicle is available for inspection upon request. The safety defect has been explicitly reproduced and confirmed in writing by an authorized Toyota Master Technician. The selling dealership management has been formally notified of this safety diagnosis but has actively refused to remediate the unsafe components, leaving a structurally compromised and highly dangerous vehicle operating on public highways.

Driving down the Highway at about 75-80 MPH and my Passenger side mirror camera flys off lost to the highway.

I have a 2022 Tundra with 18,700 miles on it that is part of the recall for a new engine! This is my fourth tundra, and the materials used in the 3rd Gen are sub-par to say the least! I have already had to replace the actuator and motor in my passenger window because it was stuck halfway open/closed and it took the dealership almost 2 weeks just to get the parts and put them in. My tailgate isn't aligned properly and the mold growth on all the rubber window trim is a nightmare as well as the roof wells that are also covered in mold up and down both sides. My rear passenger door doesn't close correctly and nobody at Toyota knows how to fix any of these issues! I am very concerned about a dealership putting a new engine in my truck when they can't even change the oil or rotate my tires correctly. I also have other serious issues like, I feel a giant thud like somebody rear ended me when I step on the gas from a red light or stop sign and sometimes when I step on the gas on the highway and it scares the heck out of me. It almost feels like the back of my truck fell off. When it's raining out and my hood is covered in water and then the rain stops and I turn my windshieldwipers off, the water that rolls down the hood is spit straight into my windshield from the radiator fan! I also took it to the dealership to fix the fuel line recall, and they said they don't have the parts available, it's been over 2 weeks now and the recall was issued last year.

Water is leaking into the cab of my 2022 Toyota Tundra Platinum 4x4 through the high-mounted third brake light. The leak allows water to enter the headliner and interior, creating the potential for mold, damage to the interior, and electrical issues. After troubleshooting, the third brake light gasket appears to be the source of the leak. Toyota does not appear to offer the gasket as a replacement part, requiring owners to replace the entire third brake light assembly despite the failure being limited to the seal. Numerous owners have reported similar water intrusion issues on 2022+ Tundras, suggesting this may be a common defect rather than an isolated incident. I believe Toyota should investigate the failed gasket design and consider a recall or service campaign to replace the defective seal or assembly.

This recall {25TA06} has been out since May 15 2025, it's been over a year now. I have called a few times and nobody know anything when this will be completed. Rumors on line say they took care of the ones at the dealership but not the ones that customers purchased. All I need is about when this will be taken care of. Thank you

This 2022 Toyota Tundra TRD Pro is subject to Limited Service Campaign 24TD01 for premature tire wear, caused by a factory front toe/camber angle defect acknowledged by Toyota. The vehicle received the campaign remedy (front alignment adjustment and tire replacement) in May 2024, but the same wear pattern on the front tires reappeared and has continued for over a year, documented across multiple dealership visits. A dealership technician found abnormal front tire wear on three separate occasions (August 2025, September 2025, and March 2026) but never recommended a front-end alignment despite Toyota's own campaign identifying alignment/camber as the root cause. As of August 2026, the right front tire tread had worn down to approximately 1/32 inch, an unsafe condition, and only then was an alignment finally recommended in writing for the first time. The vehicle also had a documented brake rotor warping issue (front rotors) as early as November 2024, causing a braking vibration above 40 mph that has persisted. The recurring tire wear presents an ongoing safety risk due to reduced traction and control, particularly relevant given the near-bald tire condition reached before any alignment correction was recommended by the servicing dealer.

The outer edges of front tires wearing excessively. They replaced 2 around 20k milage and there are many reports of the same issue from factory alignment and camber. The tire appears to be splitting prematurely.

Premature tire wear. Outside of tire on front wearing faster than inside. Had a realignment and also put on new tires. Same issue is happening

Tire size 265/60R20. All tires have cracked around the bead of the rim. This was discovered at 24,663 miles during regularly scheduled maintenance at Copeland Toyota in Brockton, MA on March 20, 2025. Defective manufacturing suspected. Upon further investigation of this tire model on the Internet, I discovered dozens of reports of the same sidewall failure by Toyota Tundra owners with very low mileage. I contacted Bridgestone Support on March 20, and per their instruction, took the vehicle to a Bridgestone authorized dealer (Firestone Complete Auto Care, Warren Ave. Brockton, MA) on March 21. The inspection determined that the tires have failed. The technician indicated that Bridgestone has very limited inventory of this tire model, indicative that the tire is being discontinued. I contacted Bridgestone Support on March 21, indicating that there is likely a manufacturing defect, and was advised to report this to the NHTSA, because the Bridgestone employee stated that they have no internal capability to report a potential manufacturing defect. I suspect there is a likelihood that these tires have been discontinued because of defects, but Bridgestone has not alerted customers of such a safety hazard. My Bridgestone Support reference number is [XXX]. Please investigate this as I believe there is a safety hazard due manufacturer defect. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

What component failed and is it available for inspection? The front driver-side roof seam on my 2022 Toyota Tundra developed corrosion under the paint and eventually opened enough for rainwater to enter the cabin. Water drips directly into the A-pillar area onto the side curtain airbag wiring, squib connector, and padded harness. It also reaches the dashboard and electrical buttons near the steering wheel during rain. The roof seam, A-pillar wiring, interior rust staining, and all affected components remain available for inspection. How was safety put at risk? The A-pillar contains the SRS curtain airbag system, its wiring, and connectors that should never be exposed to moisture. Continuous water intrusion over many months can cause corrosion, increased resistance, short circuits, or damage to the airbag inflator/squib circuit, which may lead to unintended deployment or failure to deploy in a crash. Water reaching the dashboard controls and electrical switches could cause intermittent electrical faults or malfunction of driver controls. These issues present a significant safety risk because the vehicle’s airbag and electrical systems may not function as designed. Has the problem been reproduced or confirmed? Yes. The Toyota dealer has repeatedly observed the active leak, interior rust streaks, and bubbling/corrosion along the roof seam. The water intrusion occurs every time it rains. Has the vehicle been inspected? Yes. Toyota has inspected the truck multiple times, including by a Field Technical Specialist. However, Toyota has been unable to provide complete documentation or photos from the FTS inspection, and the underlying safety issue remains unresolved. No inspections have been done by police or insurance. Warning lamps or messages? No warning lamps appeared. The first symptom was water leaking into the cabin around March 2024, followed by rust streaking inside the A-pillar and exterior bubbling. The issue continues during rainfall.

The contact owns a 2022 Toyota Tundra. The contact stated that while driving approximately 40 mph the vehicle crashed into a tree causing severe damage to the front end. During the crash, the air bags did not deploy and the collision avoidance system did not activate to prevent the crash from occurring. No injuries were reported. A police report was filed at the scene and the vehicle was towed away. The cause of the failure was not determined. The manufacturer was notified of the failure. The local dealer was not contacted. In addition, while driving at highway speeds the Tonneau cover nearly came off the vehicle. The cause of the failure was not determined. The failure mileage was 5000.

This 2022 Toyota Tundra TRD Pro is subject to Limited Service Campaign 24TD01 for premature tire wear, caused by a factory front toe/camber angle defect acknowledged by Toyota. The vehicle received the campaign remedy (front alignment adjustment and tire replacement) in May 2024, but the same wear pattern on the front tires reappeared and has continued for over a year, documented across multiple dealership visits. A dealership technician found abnormal front tire wear on three separate occasions (August 2025, September 2025, and March 2026) but never recommended a front-end alignment despite Toyota's own campaign identifying alignment/camber as the root cause. As of August 2026, the right front tire tread had worn down to approximately 1/32 inch, an unsafe condition, and only then was an alignment finally recommended in writing for the first time. The vehicle also had a documented brake rotor warping issue (front rotors) as early as November 2024, causing a braking vibration above 40 mph that has persisted. The recurring tire wear presents an ongoing safety risk due to reduced traction and control, particularly relevant given the near-bald tire condition reached before any alignment correction was recommended by the servicing dealer.

The vehicle was purchased brand new from an authorized franchised dealership, sold and contracted as being equipped with a dealer-installed 2.5-inch suspension lift. At approximately 20,000 miles, a severe front-end squeaking symptom developed. The vehicle was brought to a separate authorized Toyota dealership service center for inspection. An authorized Toyota Master Technician formally inspected the vehicle and documented that the selling dealership did not install an engineered suspension lift. Instead, they installed unauthorized, budget aftermarket spacer pucks and non-certified upper control arms. The Master Technician documented in writing that the vehicle "isn't even lifted properly" and a factory front strut has failed prematurely. SAFETY RISK: The unauthorized spacer modification has severely altered and compromised the factory steering and suspension geometry. Because the front suspension, upper control arms, ball joints, struts, and steering rack are forced to operate continuously at unsafe, extreme, out-of-spec angles, the components are subjected to premature, destructive stress. The Master Technician confirmed that this improper configuration creates an imminent highway life-safety hazard, presenting an extreme risk of the front CV axles binding or snapping at highway speeds, which would result in an immediate, catastrophic loss of steering control. The vehicle is available for inspection upon request. The safety defect has been explicitly reproduced and confirmed in writing by an authorized Toyota Master Technician. The selling dealership management has been formally notified of this safety diagnosis but has actively refused to remediate the unsafe components, leaving a structurally compromised and highly dangerous vehicle operating on public highways.