1996 Chevrolet Impala Problems

REAR VISION IS IMPARED WHEN LOOKING THROUGH BACK GLASS.THE DE-ICER/DEFROSTER HAS TURNED ( FOGGY) .THIS IS A REAL SAFETY CONCERN AT NIGHT ESPECIALLY.

HEATER CORE IN MY 1996 IMPALA IS CONSTANTLY CLOGGING, THEREFORE NO HEAT AND NO DEFROSTERS. COOLING SYSTEM FLUSHED 2 TIMES BY CHEVROLET GARAGE. THEY HAVE NO WAY TO CORRECT THE PROBLEM. THIS PROBLEM IS NATION WIDE AND NOT A LOCAL ISSUE. *JB

INABILITY TO CONTROL THE STEERING ON ROUGH ROADS. STEERING IS VERY LOOSE WHILE DRIVING AT ALL SPEEDS. ALSO, VEHICLE DARTS IN BOTH DIRECTIONS WHILE BRAKING. *AK

POWER STEERING INTERMITTENTLY LOCKS UP DURING TURNS AT LOW SPEEDS. THIS SAME THING HAPPENED 3 YEARS AGO. CHEVROLET DEALERS AND CUSTOMER SERVICE BOTH DENY ANY EVIDENCE OF A RECURRING PROBLEM WITH IMPALAS ALTHOUGH THE NHTSA WEB SITE AND AN IMPALA OWNERS' WEB SITE BOTH LIST NUMEROUS OCCURRENCES OF THIS MALFUNCTION. THIS IS A VERY DANGEROUS SITUATION THAT RENDERS THE CAR TEMPORARILY OUT OF CONTROL. *AK

TL* THE CONTACT OWNED A 1996 CHEVROLET IMPALA. THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 14V355000 (ELECTRICAL SYSTEM). WHILE DRIVING 50 MPH, THE VEHICLE STALLED AND CRASHED INTO A DITCH. THERE WERE NO INJURIES AND A POLICE REPORT WAS FILED. THE VEHICLE WAS DESTROYED. THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEAGE WAS UNKNOWN.

(1) WHILE TRAVELING THRU LAUGHLIN, NV TRAVELING WEST ON HWY 163, CAR ABRUPTLY QUITS. FUEL PUMP FUSE BLOWN. SUSPECT DYING FUEL PUMP. INSTALL NEW FUSE, TRAVEL ANOTHER 30 MILES UP HWY 95...CAR DIES AGAIN. THIS TIME, NO BLOWN FUSE. FUEL PUMP WILL NOT RUN. TOW VEHICLE TO FINAL DESTINATION (LAS VEGAS). (2) PULLED THE TANK, REMOVED THE SENDING UNIT FOR PUMP REPLACEMENT. QUICKLY NOTICED THE PROBLEM. THE FUEL PUMP WIRING INSIDE THE TANK HAD SHORTED OUT. INSULATION BURNT COMPLETELY OFF OF THE PRIMARY PUMP POWER WIRE AND SHORTED INTO THE FUEL QUANTITY GROUND WIRE. CONNECTOR AT TOP OF SENDING UNIT MELTED. (3) REPLACE SENDING UNIT, FUEL PUMP, STRAINER AND FUEL FILTER. *AK

I BOUGHT MY 1996 IMPALA SS BRAND NEW, AND EVERY YEAR SINCE THEN IN THE WINTER TIME I LOOSE THE HEAT. THE DEALER, WHILE THE CAR WAS STILL UNDER WARRANTY, WOULD FLUSH THE HEATER CORE AND SOMETIMES REPLACE IT YEARLY. THE PROBLEM STILL IS NOT FIXED, AND I HAVE LOST THE HEAT IN THE CAR AGAIN AND THE DEALER WILL NO LONGER FIX THE PROBLEM BECAUSE THEY CLAIM IT IS OUT OF WARRANTY EVEN THOUGH THEY HAVE ALL OF THE SERVICE RECORDS SHOWING THE HISTORY OF THE PROBLEM. I THINK THIS IS TOTALLY UNFAIR TO THE OWNER, AND I HAVE TALKED TO MANY CAPRICE/IMPALA SS OWNERS OF THIS YEAR WHO ARE GOING THROUGH THE SAME PROBLEM. CHEVY KNOWS OF THE PROBLEM BUT DOES NOTHING TO CORRECT IT, AND NOW THE OWNERS ARE LEFT WITH THE BILL AND IF YOU CANNOT AFFORD TO HAVE THEM FIX IT YOU DRIVE IN A COLD CAR. IF THEY DO NOT KNOW WHAT IS CAUSING THIS PROBLEM, THEN CHEVY/DEALERSHIP SHOULD BE RESPONSIBLE FOR FLUSHING OR REPLACING MY HEATER CORE(WHATEVER IS NEEDED TO RESTORE THE HEAT) FOR AS LONG AS I OWN THE CAR. I NEED SOME HELP WITH THIS, I AM ONLY A SMALL GUY FIGHTING A GIANT. ANY ASSISTANCE YOU CAN PROVIDE WOULD BE GREATLY APPRECIATED. THANKS KJB. TS

MANUFACTURER USED A PLASTIC TANK ON TOP OF RADIATOR INSTEAD OF METAL. PLASTIC TANK BECAME SPLIT, AND ANTIFREEZE POURED OUT, COULD POSSIBLY CAUSE A FIRE. PLEASE PROVIDE ANY FURTHER INFORMATION.*AK

ODOMETER INSTRUMENT CLUSTER RESISTERS OPERATE AT SUCH HIGH TEMPERTURES BECAUSE OF A LACK OF VENTILATION THAT THE SOLDER JOINTS MELT CAUSING THE ODOMETER TO FAIL .I FEEL IF THESE RESISTERS COULD FALL OUT INTO THE INSTRUMENT CLUSTER IT COULD CAUSE AN ELECTRICIAL FIRE..

ALTERNATOR SUDDENTLY STOPPED WORKING. DASH BOARD LIGHT DOESN'T ALLOW CONSUMER TO SEE THE SPEED. HE DOESN'T KNOW HOW FAST HE IS GOING. ALSO, WHEN APPLYING BRAKE AND GAS PEDALS HEADLIGHTS GO DIM. WHEN HE RELEASES GAS AND BRAKE PEDALS, HEADLIGHTS ARE FULL FORCE. *AK

FUEL PUMP FUSE BLOW OUT. THE CAR CUTS OFF AND STOPS WHILE DRIVING, BLOWING OUT THE FUSE. WHEN A NEW FUSE IS INSTALLED AND THE ENGINE IS STARTED, IT BLOWS OUT AGAIN. THE PROBLEM IS CAUSED BY A FAULTY WIRING HARNESS TO THE FUEL PUMP ASSEMBLY. THE WIRING ON THE FUEL PUMP SENDER UNIT MELTS AND PEELS BACK THE INSULATION, CAUSING THE BARE WIRES TO TOUCH AND SHORT AGAINST THEMSELVES OR GROUND OUT AGAINST THE CAR. THIS OCCURS RIGHT AT THE TOP OF THE FUEL PUMP TANK ON THE SENDER ASSEMBLY OR JUST INSIDE THE TANK. THE FUEL PUMP WIRING HARNESSES ON THESE VEHICLES ARE PROBLEMATIC AND DEFECTIVE, POTENTIALLY CAUSING A FIRE IN THE FUEL TANK AND EVENTUALLY A CATASTROPHIC EXPLOSION. A NEW FUEL PUMP SENDER (OEM PART NO. 25028955) WAS REPLACED IN ADDITION TO A NEW ELECTRIC FUEL PUMP, AND NEW FUEL FILTER. *JB

(1) WHILE TRAVELING THRU LAUGHLIN, NV TRAVELING WEST ON HWY 163, CAR ABRUPTLY QUITS. FUEL PUMP FUSE BLOWN. SUSPECT DYING FUEL PUMP. INSTALL NEW FUSE, TRAVEL ANOTHER 30 MILES UP HWY 95...CAR DIES AGAIN. THIS TIME, NO BLOWN FUSE. FUEL PUMP WILL NOT RUN. TOW VEHICLE TO FINAL DESTINATION (LAS VEGAS). (2) PULLED THE TANK, REMOVED THE SENDING UNIT FOR PUMP REPLACEMENT. QUICKLY NOTICED THE PROBLEM. THE FUEL PUMP WIRING INSIDE THE TANK HAD SHORTED OUT. INSULATION BURNT COMPLETELY OFF OF THE PRIMARY PUMP POWER WIRE AND SHORTED INTO THE FUEL QUANTITY GROUND WIRE. CONNECTOR AT TOP OF SENDING UNIT MELTED. (3) REPLACE SENDING UNIT, FUEL PUMP, STRAINER AND FUEL FILTER. *AK

ALL TIRES .TREAD SEPARATION IN PROGRESS( DOT NUMBER: N/A TIRE SIZE: 255/50ZR17 )

TIRES ARE RUBBING AGAINST THE FENDER ,EVEN WITH NORMAL AMOUNT OF WEIGHT IN THE VEHICLE, ALMOST CAUSING THE TIRE TO BLOW OUT. *AK

BOSCH ANITLOCK BRAKE SYSTEM PUMP COMPLAINT ABOUT THE FAILURE OF THE BOSCH ABS PUMP ON MY 1996 CHEVROLET IMPALA. THE REAR BRAKES FAILED ON MY AUTOMOBILE. I TOOK THE CAR TO MY MECHANIC WHO DISCOVERED A FLUID LEAK IN THE REAR BRAKES AND SUSPECTED SOME TYPE OF FAILURE WITHIN THE ANTILOCK BRAKE SYSTEM. SINCE THE CARS MILEAGE WAS ONLY 14,783 AND THE BRAKES SHOULD NOT BE FAILING ALREADY, HE TOOK THE CAR TO A LOCAL CHEVROLET DEALERSHIP, CHUCK OHL IN CHARDON, OHIO. THE CHEVY DEALERSHIPS SERVICE DEPARTMENT DIAGNOSED THE TROUBLE AS ABS PUMP FAILURE, SO THEY REPLACED THE BOSCH UNIT FOR $1,635 BILLED TO MY MECHANIC. CHEVROLET HAD NO REPORTED RECALLS ON THIS UNIT AND SINCE THE NEW CAR WARRANTY OF 36,000 MILE/3 YEARS IS EXPIRED, I WAS LEFT TO PAY $1725.14 (INCLUDES TAX) FOR THE NEW BOSCH ABS PUMP. CHEVROLET SERVICE LISTED THE ABS PUMP LEAKING DUE TO CORROSION. I KEPT THE ORIGINAL PUMP- THERE IS NO CORROSION ON IT OR ANY OTHER AREA OF THE VEHICLE. I AM THE ORIGINAL OWNER OF THIS CAR AND HAVE KEPT IT GARAGED EVERY WINTER FROM OCTOBER TO MAY. THEREFORE, IT SUFFERS NO CORROSION FROM OHIO WINTERS. THE BRAKE PADS AND ROTORS ARE IN EXCELLENT CONDITION. IN NO WAY HAVE THE BRAKES BEEN ABUSED ON THIS VEHICLE. THE ONLY REASONABLE EXPLANATION FOR THIS BRAKE FAILURE IS THE ORIGINAL BOSCH ABS PUMP WAS DEFECTIVE. I WROTE COMPLAINT LETTERS TO CHEVROLET AND TO BOSCH. CHEVY CUSTOMER ASSISTANCE HAS NEVER ANSWERED MY LETTER BUT I CALLED & THEY DENIED THE CLAIM BECAUSE THE CAR IS NO LONGER UNDER WARRANTY. BOSCH ANSWERED IN WRITING. WITH NO CORROSION ON MY VEHICLE AND THE ABS WARNING LIGHT HAS NEVER ILLUMINATED, BOSCH'S EXPLANATION FOR THE ABS PUMP FAILURE SUGGESTS THE BRAKE SYSTEM ABSORBED MOISTURE. THEY ALSO STATE THE BRAKE FLUID SHOULD BE REPLACED EVERY 1 TO 2 YEARS, "LIKE MANY VEHICLE MANUFACTURERS INCLUDE IN RECOMMENDED MAINTENANCE SCHEDULES." I HAVE CAREFULLY CHECKED THE CHEVROLET OWNER'S MANUAL DELIVERED WITH MY VEHICLE-CHANGING BRAKE FLUID IS NOT MENTIONED. *AK

LF DISC BRAKE CALIPER HAS HAD A PROBLEM WITH NOT RELEASING OR "FLOATING" PROPERLY. THIS HAS CAUSED ACCELERATED WEAR TO THE OUT BRAKE PAD. DEALER HAS BEEN UNABLE TO CORRECT. I HAD TO CORRECT MYSELF. I AM AN ASE MASTER AUTO TECHNICIAN. DEALER STATED THAT THIS WAS "NORMAL" WHICH IT IS NOT. IF I WAS NOT A TRAININED, CERTIFIED AND LICENSED BRAKE TECHNICIAN THE PROBLEM WOULD NOT HAVE BEEN DETECTED AND/OR CORRECTED. THIS COULD HAVE LEAD TO REDUCED BRAKING ABILITY AND POSSIBLE ACCIDENT. *AK

CHEVROLET DEALERSHIP WILL NOT HONOR THE RECALLS YOU HAVE PLACED ON THE CAPRICE CAR I HAVE. *AK

THE LOWER BALL JOINT EXPERIENCED THE SAME FAILURE AS STATED IN THE RECALL, HOWEVER THE VEHICLE IDENTIFICATION NUMBER WAS NOT INCLUDED IN THE RECALL. *JB

FRONT SEAT BELT RETRACTOR AND MOTION LOOK-UP DEVICE FAILLED WITHOUT WARNING. UPON REPLACEMENT FOUND THAT THE RETRACTION SPRING HAD WORN THROUGH THE PLASTIC SIDE COVER. FALURE OCCURRED WHEN I LEANED FORWARD AND APPLIED FORCE TO THE SEAT BELT SHOULDER HARNESS. IF IT HAD OCCURRED IN AN ACCIDENT, I WOULD NOT HAVE BEEN RESTRAINED.

THE DRIVER SIDE SEATBELT WAS INOPERATIVE. WHEN SEATBELT WAS EXTENDED OUTWARD, IT WOULD NOT RETRACT. BY ASSUMPTION, CONSUMER TESTED THE BELTS BY SLAMMING ON BRAKES, AND THEY DIDN'T RETRACT. TS CONSUMER ALSO REMOVED THE MOLDING AND FOUND THE RECOIL SPRING WAS PROTRUDING OUT OF HOLE ON THE COVER. *TT *JB

BACK IN NOVEMBER 1995 I PURCHASED A NEW 1996 CHEVROLET IMPALA. I BROUGHT THE VEHICLE TO MY HOME AND DID A COMPLETE VEHICLE INSPECTION. WHAT I FOUND WAS THE DEALERSHIP LANAN CHEVROLET OF WOBURN MASSACHUSETTS DID A POOR JOB PREPPING THE VEHICLE FOR DELIVERY. WHAT I FOUND WAS THE LUG NUTS FOR THE WHEELS, ALL WERE LOOSE. I GOT MY TORQUE WRENCH AND TORQUED THE WHEEL NUTS TO THE 100FT LBS. I ALSO FOUND THE FRONT END COMPONENTS WERE NOT GREASED. I CALLED UP THE DEALERSHIP AND TOLD THEM THEY DID A LOUSY JOB.. TODAY 2014 SINCE GM HAS 30 MILLION RECALLS I THOUGHT I WOULD CHECK MY VEHICLES FOR ANY RECALLS . WHAT I FOUND WAS , THE LOOSE LUG NUTS ARE LISTED AS AN INCOMPLETE RECALL ON THIS VEHICLE. SINCE NOV 1995 THESE LUG NUTS HAVE BEEN REMOVED AND RE TORQUED ABOUT 50 TIMES. I CALLED THE DEALERSHIP TO CLEAR THIS RECALL FROM THE GM DATA BASE AND THE SERVICE GUY SAYS YOU HAVE TO BRING THE VEHICLE IN ..THIS IS STUPID ! *TR

CLEAR COATING ON THE RIGHT FRONT WHEEL RIM BASE IS BLISTERING. *AK

THE VEHICLE WAS STARTED & IMMEDIATELY THE LOCKS BEGAN ENGAGING & DISENGAGING IN RAPID SEQUENCE, THEN THERE WAS A SNAP AND I BEGAN TO SMELL BURNING WIRES. I NOTICED SMOKE RISING TO MY LEFT COMING FROM THE OUTSIDE HOOD VENTS. I TRIED TO GET OUT OF THE VEHICLE BUT I COULD NOT UNLOCK OR OPEN THE DRIVERS DOOR. I HAD TO MANUALLY UNLOCK THE DOOR. MY HUSBAND CAME OUT AND CHECKED UNDER THE HOOD HE SAW SMOKE COMING FROM AROUND THE FIRE WALL. HE THEN LOOKED UNDER THE DRIVERS SIDE DASH BOARD AND SAW FLAMES. I AT THAT POINT CONTACTED 911 AND HE WAS ABLE TO PUT OUT THE FIRE WITH A GARDEN HOSE. THE FIRE COMPANY ARRIVED AND CHECKED TO MAKE SURE THE FIRE WAS OUT, THEY DISCONNECTED THE BATTERY. I AM GLAD I WAS OF A CLEAR FRAME OF MIND OR I WOULD HAVE BEEN LOCKED IN THE CAR. WE COULD NOT OPEN ANY OF THE OTHER DOORS OF THE VEHICLE WITHOUT UNLOCKING THEM MANUALLY. THE VEHICLE FILLED WITH SMOKE WHICH WAS VERY TOXIC. THIS COULD HAVE DEVELOPED INTO A VERY SERIOUS LIFE THREATENING SITUATION IF I HAD NOT GOTTEN OUT OF THIS VEHICLE. I HAVE CONTACTED GENERAL MOTORS AND THEY ARE NOW INVOLVED IN THE INVESTIGATION WITH THE DEALERSHIP.

LEFT/RIGHT CONTROL ARM ASSEMBLIES FAILED TWICE.

ENGINE SURGES WHEN COMING OFF OF IDLE. DEALER HAS STATED IT IS A KNOW PROBLEM AND THAT GMC IS WORKING ON A FIX FOR THE EGR VALVE. *AK

A PIECE OF PLASTIC THAT CAME FROM THE AIR CLEARNER AND INTAKE MANIFOLD FROM BEHIND DROPPED INTO THE THROTTLE, CAUSING THE THROTTLE THE BE WIDE OPEN.

LEFT/RIGHT CONTROL ARM ASSEMBLIES FAILED TWICE.

OIL COOLER LINES ROUTED SO THEY RUB AGAINST METAL, CAUSING HOLES/LEAK.

THE CONSUMER NOTICED THAT WHEN IT RAINED, THE PASSENGER'S SIDE FLOOR WAS SOAKED DUE TO A LEAK INSIDE THE VEHICLE. *AK *SC *JB

PASSENGER'S DOOR STUCK.

ALTERNATOR SUDDENTLY STOPPED WORKING. DASH BOARD LIGHT DOESN'T ALLOW CONSUMER TO SEE THE SPEED. HE DOESN'T KNOW HOW FAST HE IS GOING. ALSO, WHEN APPLYING BRAKE AND GAS PEDALS HEADLIGHTS GO DIM. WHEN HE RELEASES GAS AND BRAKE PEDALS, HEADLIGHTS ARE FULL FORCE. *AK

CONSUMER WAS INVOLVED IN A FRONTAL COLLISION, AND THE AIR BAGS FAILED TO DEPLOY.*JB