2021 GMC Yukon Xl Engine Problems

INCIDENT 4: Fuel Injector Internal Short (Cylinder #6) Component / System Failed: Fuel Injection System / Cylinder #6 Fuel Injector & Wiring Harness Failure Description: Cylinder 6 fuel injector failed due to an internal electrical short circuit, causing immediate engine misfires and severe power reduction. Repair required replacing the Bank 2 fuel rail, four fuel injectors, and the injector wiring harness. Safety Risk: Immediate engine shuddering and abrupt drop in drive power while operating in active traffic creates a serious loss-of-acceleration hazard and heightened risk of a rear-end collision. Dealer / Repair Shop Confirmation: Official diagnosis confirmed by Service Center Technician via electronic diagnostics verifying the internal electrical short circuit. Warning Symptoms: Check Engine Light illuminated simultaneously with engine shaking and sudden power loss; no prior symptoms existed before the failure. Inspection Availability: Confirmed via technician diagnostics; Check Engine light illuminated along with four other warning lights- car had to be towed to dealership to be fixed

NHTSA ID

11775683

Incident

Oct 13, 2026

INCIDENT 3: Fuel Pump Driver Module (FPDM) Failure Component / System Failed: Fuel Pump Driver Module (FPDM - Part #13554821) / Engine Control Module (ECM) Communication Failure Description: Total loss of communication between the ECM and FPDM, causing the engine to abruptly die while idling at a traffic light. Subsequent attempt to restart using push-to-start produced a severe mechanical screeching noise. Safety Risk: Unexpected stall in active traffic left the vehicle stranded and unable to restart safely, exposing occupants to collision hazards. Dealer / Repair Shop Confirmation: Confirmed by Service Technician. Diagnostic Code P129F ("ECM lost communication with fuel pump driver module") logged; verified power and ground failures at the module. Replaced FPDM (Part #13554821). Warning Symptoms: None prior to failure. Sudden engine shutdown followed by screeching sound on attempted restart. Inspection Availability: Vehicle and replaced module are available for inspection upon request.

NHTSA ID

11775676

Incident

Mar 10, 2026

INCIDENT 2: Total Electrical / Power System Shutdown Component / System Failed: Electrical / Power Control System (Auto-Stop/Start System) Failure Description: Total loss of electrical power causing the main dashboard and display screen to go completely dark, stalling the vehicle during an autostop event at a traffic light and preventing the engine from restarting. Safety Risk: Sudden total electrical shutdown leaves the vehicle completely dead, unresponsive, and immobilized in active traffic lanes/intersections, creating a high risk of rear-end or multi-vehicle collisions. Dealer / Repair Shop Confirmation: Customer complaint and active fault codes confirmed by dealership service department following standard maintenance schedule. Warning Symptoms: Display screen went blank; failure occurred instantly during autostop/traffic light stop without prior warning. Inspection Availability: Vehicle and affected systems are available for inspection upon request. INCIDENT 3: Fuel Pump Driver Module (FPDM) Failure Component / System Failed: Fuel Pump Driver Module (FPDM - Part #13554821) / Engine Control Module (ECM) Communication Failure Description: Total loss of communication between the ECM and FPDM, causing the engine to abruptly die while idling at a traffic light. Subsequent attempt to restart using push-to-start produced a severe mechanical screeching noise. Safety Risk: Unexpected stall in active traffic leaves the vehicle stranded and unable to restart safely, exposing occupants to collision hazards. Dealer / Repair Shop Confirmation: Confirmed by Service Technician. Diagnostic Code P129F ("ECM lost communication with fuel pump driver module") logged; verified power and ground failures at the module. Replaced FPDM (Part #13554821). Warning Symptoms: None prior to failure. Sudden engine shutdown followed by screeching sound on attempted restart. Inspection Availability: Vehicle and replaced module are available for inspection upon request.

NHTSA ID

11775670

Incident

Mar 7, 2024

INCIDENT 1: Internal Engine Failure & Excessive Oil Consumption Component / System Failed: Engine Internal Components (Piston Rings, Valve Guide Seals, Spark Plugs) Failure Description: Excessive oil consumption (1.5 to 2.0 quarts burned every 2,000 miles) leading to heavy oil-fouling on spark plugs #5 and #7. Required complete cylinder head, oil pan, and piston teardown to replace all pistons, rings, connecting rod bearings, lifters, guides, valve guide seals, and spark plugs. Safety Risk: Severe internal engine oil consumption and plug fouling create an immediate risk of engine misfires, unexpected loss of power, or catastrophic engine failure while driving at highway speeds. Dealer / Repair Shop Confirmation: Confirmed by Dealership Service Department via oil consumption tests, spark plug inspection with oil dye, compression tests, cylinder leak-down tests, and physical teardown. Warning Symptoms: Low oil warning lamp illuminated; continuous need to top off oil between routine maintenance services. Inspection Availability: Vehicle and replaced components are available for inspection upon request.

NHTSA ID

11775607

Incident

Nov 14, 2020

The contact owned a 2021 GMC Yukon XL. The contact stated that while driving 75 MPH, the vehicle suddenly shut off and lost power in the middle of traffic. The contact attempted to restart the vehicle, but the vehicle failed to restart. The contact stated that the emissions warning light and the drivetrain warning light were illuminated. The manufacturer was notified of the failure and offered to pay half of the cost of the engine repair. The vehicle was towed to a dealer, where it was diagnosed with lifter and rod failures. The contact stated that the manufacturer was aware of the 6.2L engine failures. The failure mileage was 9,000.

NHTSA ID

11775183

Incident

Jun 1, 2026

Mileage

9,000 mi

I own a 2021 GMC Yukon XL Denali equipped with the 6.2L L87 V8 engine (VIN: [XXX]). At approximately 149,000 miles, the engine developed a significant internal mechanical failure requiring complete replacement. The vehicle was diagnosed by Lexington Park Chevrolet Buick GMC, an authorized GM dealership in [XXX]. The technician identified a misfire in cylinder #5, significant oil contamination of the combustion chamber and spark plug, and broken oil-control rings on piston #5. The technician also documented bottom-end engine noise and determined that replacement of the engine assembly was necessary. The dealership replaced the engine with a GM remanufactured 6.2L L87 engine (part number 19420611), at an estimated cost of $10,950. Although my vehicle was not included in GM Safety Recall 25V-274 (N252494000), I am concerned that this significant internal engine failure may be relevant to NHTSA's ongoing investigation of L87 engine failures, particularly those occurring in vehicles outside the original recall population. I request that NHTSA review and document this failure as part of its ongoing evaluation of the L87 engine and the scope of the existing recall. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11775180

Incident

Aug 18, 2026

Engine failure at approximately 72,000 miles. The vehicle had been inspected by GM dealer and passed the pico test at approximately 60,000 miles. GM suggested repair of 0w40 oil with new oil cap and driver's manual insert was completed.

NHTSA ID

11775021

Incident

Oct 8, 2026

**Mileage at repair:** 76,165 miles **Component:** Fuel Pump Power Control Module While driving my 2021 GMC Yukon XL on [XXX] on a treacherous stretch decending [XXX] the engine unexpectedly stopped running, resulting in a complete loss of propulsion. This occurred on a section of interstate where there was no safe shoulder or suitable location to pull off the roadway. The unexpected failure created an extremely dangerous situation, exposing me and other motorists to the risk of a serious collision. The vehicle was subsequently towed, diagnosed and repaired by Darrell Waltrip Buick GMC in [XXX]. The dealership documented diagnostic trouble code P129F, "Fuel Pump Driver Control Module Fuel Pump Speed Signal Incorrect." The technician verified that the control module had proper electrical power, that there was no pin damage or connector fitment issue, and that the module required replacement. The dealership's written diagnosis specifically acknowledges that a failing fuel pump driver module can cause the engine to shut down. The original factory-installed module was replaced with GM part number 13554821, and the vehicle was subsequently tested and confirmed to operate correctly. The repair was performed at no charge, and GM provided a loaner vehicle while the replacement part was unavailable. I am particularly concerned that General Motors has previously acknowledged this same type of safety hazard under NHTSA Safety Recall 21V-739 (GM N212332040), involving fuel pump power control modules on certain 2021 GM full-size SUVs. That recall identifies unexpected engine stalling and increased crash risk as consequences of module failure. My experience demonstrates the potentially catastrophic consequences of this failure in actual highway operation. I request that NHTSA investigate whether a mandatory recall and replacement of these defective components is necessary as the consequences of immediate complete unexpected loss of propulsion. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C.

NHTSA ID

11774053

Incident

Oct 17, 2026

On September 21, 2026, my 2021 GMC Yukon XL Denali with the 6.2L V8 engine experienced a serious engine failure at approximately 83,330 miles while traveling on Interstate 10 near Litchfield Road in Arizona. The vehicle developed engine knocking and subsequently stalled, leaving my family and me at risk on the highway. This was a serious safety concern because the engine failed unexpectedly during operation. The GMC dealership determined that the engine needed to be replaced under warranty. The replacement engine was installed in October 2026, and I received the vehicle back on October 13, 2026. My concern is that the dealership installed a remanufactured engine, and I have not received sufficient documentation confirming whether the replacement addresses the underlying defect associated with the GM 6.2L engine failures. I am concerned about the possibility of another catastrophic engine failure, particularly while traveling at highway speeds with my family. I am requesting that NHTSA investigate this engine failure and determine whether the replacement engine adequately addresses the safety defect. I believe these failures present a serious risk to drivers, passengers, and other motorists.

NHTSA ID

11771244

Incident

Oct 14, 2026

High oil consumption, will have oil changed and days later need oil, catalyst converter failed causing what was said for the check engine light to come on, truck now has a shutter around 50 mph, my radio is in and out, and sometimes it sounds like a computer shutting down. It has been one thing after the next.

NHTSA ID

11771151

Incident

Oct 13, 2025

The vehicle is consuming every bit of oil at about 1500 to 1800 miles of the 3000 mile guidelines before the next oil change. No leaks. No smoke. No knocking in motor.

NHTSA ID

11767641

Incident

Sep 28, 2026

Engine coolant control valve has failed three times. This last time so severely the car forced me to come to a complete stop in the middle of a busy street. Dangerous to drive while severe reduced acceleration is all that’s available during the episodes.

NHTSA ID

11765500

Incident

Sep 19, 2026

Vehicle has been consuming engine oil at a rate of approximately 1 quart per 500 miles. On XXX, owner added 1 quart of oil in [XXX], then drove a round trip to [XXX] and back (approx. 860 miles). On XXX at 55,329 miles — only 9 days and roughly 860 miles after that quart was added — an oil change was performed at an independent shop; the technician noted no oil was present on the dipstick prior to service. On XXX at 55,829 miles — exactly 500 miles later — the vehicle was taken to an authorized GMC dealership, and the dipstick again showed no oil prior to service. The dealer began the manufacturer's oil consumption test protocol, performing an oil and filter change and other maintenance. Within approximately 74 miles of this service (current mileage 55,903), the engine began making an audible knocking noise. Oil level was checked and confirmed full/normal, ruling out low oil as the cause. The knock has been intermittent — not present at cold idle start, but returning during driving conditions, raising concern about potential engine failure or loss of power while driving. They can not get it back in till XXX. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11765236

Incident

Aug 28, 2026

The rod bearing failed while traveling at highway speeds, so yes our safety as well as others traveling on the interstate. It is available for inspection. A dealership inspected and confirmed the reported problem. The manufacturer is aware of the persistent problems with these vehicles' engine components, reliability and safety. There were not any symptoms, warning lights, etc. prior to failure. I had just purchased the vehicle and it was inspected by two independent mechanics prior to failure. I have contacted the manufacture to find that my VIN was not covered under the recall. The recall covers vehicles manufactured starting 3/1/2021, my vehicle was manufactured 10/2020. THE RECALL SHOULD BE EXPANDED TO COVER ALL OF THESE VEHICLES.

NHTSA ID

11764288

Incident

Sep 13, 2026

According to the GM Dealership the rod bearing failed disabling the engine. Dealer recommends replacing the entire engine. This consistent with recall N 252494000-N252494003 but my VIN is not included in the recall. Estimated repair $11,200. Our family was traveling roughly 55 mph on the interstate at the time of incident.

NHTSA ID

11764136

Incident

Sep 13, 2026

The engine failed, shop confirmed and replaced motor. No warning lamps on dash.

NHTSA ID

11763845

Incident

Aug 14, 2026

I own a 2021 GMC Yukon XL Denali equipped with the 6.2L L87 V8 engine. On September 10, 2026, we checked the engine oil and discovered that it was approximately two-thirds low. Mechanical inspection confirmed that the engine is consuming and burning oil internally rather than losing it through an external leak. The vehicle’s last oil change was performed in May 2026, and it is still more than 1,000 miles away from its next scheduled oil change. The vehicle provided no low-oil, low-oil-pressure, check-engine, or other dashboard warning, despite being severely low on oil and having its alerts enabled. I had no indication that the engine was operating with an unsafe amount of oil. I am concerned that the continued internal oil consumption could cause premature engine damage, engine seizure, or sudden loss of propulsion without adequate warning. I regularly use this vehicle to transport my young children. My VIN is not currently included in Recall 25V-274, although my vehicle has the same model year and 6.2L L87 engine involved in the ongoing NHTSA investigation. I am reporting this confirmed internal oil consumption and lack of driver warning so that problems occurring in currently excluded vehicles can be properly documented and investigated.

NHTSA ID

11763520

Incident

Sep 10, 2026

My 2021 GMC Yukon XL Denali with the 6.2L L87 V8 has experienced two significant lifter/valvetrain failures. The first occurred at approximately 6,500 miles and was repaired by a GMC dealer. That failure involved cylinder #4, including a collapsed/stuck lifter and bent pushrod. The current failure occurred at approximately 110,269 miles. The vehicle initially operated normally. While traveling about 10 mph and approaching a major thoroughfare, the engine suddenly began making a loud knocking noise and the vehicle began shaking violently. There were no warning lights or other symptoms beforehand. Three children were in the vehicle. When the driver attempted to accelerate, the vehicle failed to gain speed normally, and additional accelerator input made the knocking and shaking significantly worse. The check-engine light began flashing, and “Service ESC” and “Service Traction Control” warnings appeared, along with multiple other warning lights. The engine continued running. The driver made a U-turn before entering the major roadway and drove about 0.2 miles very slowly back home. An independent repair facility diagnosed P0305, cylinder #5 misfire. Moving the ignition coil and spark plug did not move the misfire, and the #5 spark plug was oil-soaked. A GMC dealer later confirmed a stuck lifter on cylinder #5 and advised that the failed lifter damaged the camshaft. My concern is the sudden loss of normal acceleration and severe engine malfunction without warning, especially because this same L87 engine previously suffered a major lifter failure at low mileage. I am asking NHTSA to determine whether repeated L87 lifter/valvetrain failures represent an additional safety-related defect or failure pattern.

NHTSA ID

11763260

Incident

Aug 18, 2026

We had to have an engine replaced because of engine failure. The new engine was provided by GMC free of charge. The second engine also failed and was also replaced by GMC.

NHTSA ID

11762580

Incident

Nov 1, 2024

I purchased this vehicle 06/14/2026 The vehicle dash started lighting up like a Christmas tree. It was taken to GM Ed Morse Freedom Chevrolet X 3 separate occasions. The lights in the dash were intermittent. Dealership couldn't duplicate the issue. I was told if they aren't active they can't duplicate. The vehicle continued to illuminate on and off after it was returned July 26th. Then August 23 i was driving and it died right in the highway putting me in a bad spot in traffic. I. There was no illuminated symbols in the dash it just died as the symbols them lit up in the dash. I had it towed by AAA thinking just a battery or starter. I was told by GM dealership the engine seized. Propulsion, metal in the oil and the crankshaft failure. The exact recall problem. My Vin fell just outside of GM internal N252494003 program of 150,000 10 year extended warranty. I have 114, 689. 2021 yukon Denali. THE exact engine failure GM put out. GM is refusing to replace the engine. The engine has been torn down. I received pictures of my claim above. It's still at GM . I've opened a corporate GM case. I'm hitting a brick wall

NHTSA ID

11762576

Incident

Aug 16, 2026

Vehicle is equipped with the 6.2L L87 V8 engine. Prior to receiving the dealer service for Recall 25V-274, the vehicle experienced a distinct highway vibration, powertrain shudder, and fluctuating/jumping RPMs on the highway. The dealer subsequently performed the recall remedy by updating the vehicle to the thicker 0W-40 oil specification. However, the underlying transmission torque converter had already suffered catastrophic failure due to the powertrain stress/shudder and required a complete transmission replacement at 84,000 miles. I am reporting this because the initial 6.2L engine defect and subsequent recall remedy overlap heavily with severe powertrain and torque converter failures at low mileage

NHTSA ID

11761330

Incident

Apr 30, 2026

Our 2021 YukonXL started running rough and the check engine light came on. We took it to the shop the next day and was told there was complete lifter failure and that we need a new engine.

NHTSA ID

11761201

Incident

Aug 16, 2026

the engine started knocking and vehicle shaking while on interstate. vehicle was towed to service center and they determined that one valve was stuck and another one turned 90 degrees and the cam shaft was also ruined. It was required to replace the engine as that was a less costly option than replacing the damaged parts. A dash light came on and was flashing while my daughter was driving it to [XXX]. The vehicle was towed from the parking lot they were at when reaching [XXX]. Unsure of where the engine went to after the service center removed it, but I think they had to send it back to GM. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11761076

Incident

Aug 3, 2026

I have a 6.2L that we took in with bad rods due to the cam. The fixed the motor and now it is consuming oil and GM says it is normal. Normal for an engine to consume quarts of oil?? I cannot trade out of the vehicle because of the extreme depreciation that these vehicles have incurred due to the known engine issues. I know others are having the same issues I just want GM to make this right and help loyal customers.

NHTSA ID

11760388

Incident

Mar 28, 2025

Lifter/camshaft/engine failure. GM knows this is an issue with these models/years. They only want to cover half of the repair sticking me with a bill for $5600. Safety is a concern because they know this is an issue and not issuing a recall currently. I waS driving when this happened which could have caused me to get into an accident. Very dangerous. Car is currently as GMC Started by showing low oil in between oil changes last year. Went in for an oil change and told them about it. Dealership told me it was the air hose box and that they didn't see any other issue. I believe they are told to lie to get each customer further out of warranty. I was driving and all of a sudden the car started violently shaking and lights started flashing at me.

NHTSA ID

11759486

Incident

Aug 22, 2026