2022 Jeep Wrangler Problems

2022 Wrangler 4xe plug-in hybrid. The hybrid high-voltage system failed the first time it was used, in April 2026 at about 35,000 miles. I had not charged or used hybrid mode before that because of the manufacturer's high-voltage battery fire-risk recall guidance (recalls 23V-787, 24V-720, 25V-741) not to charge and to park away from structures. The check engine light came on at first use and has not stayed off except when cleared by the dealer. The vehicle was taken to an authorized Jeep dealer for the same hybrid high-voltage system concern on 4/19/2026, 6/17/2026 and 7/5/2026 without a fix. On 8/4/2026 the vehicle would not start at all and had to be towed. It stayed at the dealer 29 days (8/6 to 9/4/2026). The dealer replaced the main battery and found DTC P0E15-00 (electric coolant heater performance) with the high-voltage coolant heater in a 'locked permanent' unrecoverable state, and replaced the HV heater. The three earlier visits never identified this high-voltage thermal-management failure. Safety risk: a sudden no-start / loss of propulsion, and a failed cooling component in the high-voltage system of a vehicle population already under repeated battery thermal-runaway / fire recalls, where the manufacturer has acknowledged fires in vehicles that had received earlier remedies. The failures were confirmed and documented by the dealer on repair orders. The manufacturer (Stellantis) has been notified in writing and has declined to repurchase the vehicle. Repair orders are available on request.

My 2022 Jeep Wrangler 4xe has an intermittent loss of acceleration when operating in Electric Mode. As the battery charge decreases, electric propulsion power can become significantly reduced. Pressing the accelerator sometimes produces inadequate acceleration until the gasoline engine engages. This creates a safety concern when entering traffic, crossing intersections, merging, or climbing hills because the vehicle may provide substantially less acceleration than expected. There is no warning message or warning light before or during the loss of acceleration. On a separate occasion, the vehicle displayed “Electric Mode Unavailable” with approximately 50% battery charge and switched to Hybrid Mode. Electric Mode became available again several minutes later. The vehicle has been inspected by two authorized Jeep dealers. No diagnostic codes were found, and the most recent dealer stated the vehicle was operating normally. The problem remains intermittent and has not been reproduced by the dealer. The vehicle and its components are available for inspection upon request. The vehicle previously operated normally in Electric Mode. My primary safety concern is the unpredictable loss of expected acceleration without warning, particularly when acceleration is necessary to safely enter or merge with traffic.

After the 68C software recall the vehicle no longer operates the same as prior update in electric mode! While driving in electric mode and on a flat to fairly flat road and with a 50% or less battery the gas engine suddenly starts!! Revs to 3000+rpms then drops to 1500, back up to 2500, back to 1500 then shuts off! The gas engine isn't needed at that time!! When this happens it sort of confuses the drive train and may experience a loss of power. This may happen one or two more times before the battery runs out and it switches to hybrid mode. Hybrid mode works normally! This abnormality only occurs in the electric mode! This is scary when it happens and it started right after the 68C recall. I talked to the Jeep dealership service department and they checked for fault codes and there were none. I asked if they would open a STAR report and they said they did Although it's next to impossible to duplicate it for them as there's no way to tell when it will happen and it doesn't last more than a minute or two. I don't know what to do about this and neither does the service department Calling Jeep Customer Support does nothing as there is no way to talk to the technical department. I'm at a loss other than to report it here. I have heard from other 4xe owners having the exact same issues after the 68C recall. Please help.

My 2022 Jeep Wrangler 4xe has an intermittent loss of acceleration when operating in Electric Mode. As the battery charge decreases, electric propulsion power can become significantly reduced. Pressing the accelerator sometimes produces inadequate acceleration until the gasoline engine engages. This creates a safety concern when entering traffic, crossing intersections, merging, or climbing hills because the vehicle may provide substantially less acceleration than expected. There is no warning message or warning light before or during the loss of acceleration. On a separate occasion, the vehicle displayed “Electric Mode Unavailable” with approximately 50% battery charge and switched to Hybrid Mode. Electric Mode became available again several minutes later. The vehicle has been inspected by two authorized Jeep dealers. No diagnostic codes were found, and the most recent dealer stated the vehicle was operating normally. The problem remains intermittent and has not been reproduced by the dealer. The vehicle and its components are available for inspection upon request. The vehicle previously operated normally in Electric Mode. My primary safety concern is the unpredictable loss of expected acceleration without warning, particularly when acceleration is necessary to safely enter or merge with traffic.

The vehicle experiences a severe, violent, and sudden side-to-side shaking of the front suspension and steering wheel (commonly known as "death wobble"). This dangerous oscillation typically occurs at highway speeds (approx. 55–70 mph) immediately after the vehicle strikes a normal highway bump, expansion joint, or pothole. Note: As a 4xe plug-in hybrid model, the vehicle carries substantially more curb weight than a standard internal combustion engine Wrangler due to the heavy battery pack and electric drivetrain components. This increased mass significantly magnifies the physical forces and wear placed on the front suspension and steering linkage during impact. Despite having less than 30,000 original miles and no history of accidents, the vehicle exhibits rapid component failure. Front-end steering and suspension components—including the inner drag link and tie rod ends—were previously replaced and aligned on March 17, 2026. However, the exact same dangerous steering instability and component wear reoccurred by September 17, 2026, indicating a persistent, underlying design or durability defect that standard parts replacement fails to resolve. When this failure occurs, vehicle control is severely compromised, requiring the driver to abruptly decelerate in active traffic to regain control of the steering mechanism. This poses an extreme safety hazard to the occupant and surrounding motorists, creating a high risk of a collision or loss of vehicle control.

At highway speed, vehicle repeatedly started shaking and vibrating violently after hitting any bump or uneven portion of the roadway. Steering became extremely difficult to control and was completely useless for a period of time. A vehicle that loses the ability to steer at highway speeds puts everyone at risk of accident/death. In looking online, this has been experienced by many people and is referred to as the "death wobble". There were no warnings that this was going to occur. Vehicle has been brought to the dealership. It appears unlikely that the dealership and/or manufacturer is going to fix this problem without payment.

2022 Wrangler 4xe plug-in hybrid. The hybrid high-voltage system failed the first time it was used, in April 2026 at about 35,000 miles. I had not charged or used hybrid mode before that because of the manufacturer's high-voltage battery fire-risk recall guidance (recalls 23V-787, 24V-720, 25V-741) not to charge and to park away from structures. The check engine light came on at first use and has not stayed off except when cleared by the dealer. The vehicle was taken to an authorized Jeep dealer for the same hybrid high-voltage system concern on 4/19/2026, 6/17/2026 and 7/5/2026 without a fix. On 8/4/2026 the vehicle would not start at all and had to be towed. It stayed at the dealer 29 days (8/6 to 9/4/2026). The dealer replaced the main battery and found DTC P0E15-00 (electric coolant heater performance) with the high-voltage coolant heater in a 'locked permanent' unrecoverable state, and replaced the HV heater. The three earlier visits never identified this high-voltage thermal-management failure. Safety risk: a sudden no-start / loss of propulsion, and a failed cooling component in the high-voltage system of a vehicle population already under repeated battery thermal-runaway / fire recalls, where the manufacturer has acknowledged fires in vehicles that had received earlier remedies. The failures were confirmed and documented by the dealer on repair orders. The manufacturer (Stellantis) has been notified in writing and has declined to repurchase the vehicle. Repair orders are available on request.

After the 68C software recall the vehicle no longer operates the same as prior update in electric mode! While driving in electric mode and on a flat to fairly flat road and with a 50% or less battery the gas engine suddenly starts!! Revs to 3000+rpms then drops to 1500, back up to 2500, back to 1500 then shuts off! The gas engine isn't needed at that time!! When this happens it sort of confuses the drive train and may experience a loss of power. This may happen one or two more times before the battery runs out and it switches to hybrid mode. Hybrid mode works normally! This abnormality only occurs in the electric mode! This is scary when it happens and it started right after the 68C recall. I talked to the Jeep dealership service department and they checked for fault codes and there were none. I asked if they would open a STAR report and they said they did Although it's next to impossible to duplicate it for them as there's no way to tell when it will happen and it doesn't last more than a minute or two. I don't know what to do about this and neither does the service department Calling Jeep Customer Support does nothing as there is no way to talk to the technical department. I'm at a loss other than to report it here. I have heard from other 4xe owners having the exact same issues after the 68C recall. Please help.

68C recall software update has caused some form of loss of power, doesn’t fully power off, it feels as if it is throttling the electric motor causing the engine to suddenly start and rev high (5-7k RPM) bypassing the warm up time that’s built into the software for the engine. Now on 09/14/2026 (Monday) the vehicle through a DTC code “P0BBE-00” High Voltage Battery Voltage Variation. It went into limp mode while attempting to drive up the roll back (flatbed tow truck). Currently awaiting Dealer diagnostic.

I am submitting this complaint regarding a critical electrical issue and potential safety hazard that occurred immediately after the 68C safety recall software update was performed. Since the 68C recall completion, my vehicle has experienced significant overnight High Voltage (HV) battery drain, losing approximately 10% of its state of charge while parked and powered off. I have returned the vehicle to the dealership three times for diagnostic testing. On the most recent visit, the dealership, working with Jeep engineers, claimed that the radio system fails to sleep, causing a continuous power draw from the battery. However, the dealership and Jeep engineer attributed this failure to a dash cam plugged into the factory 12V auxiliary power outlet (cigarette lighter socket). I believe this diagnosis is technically flawed and incorrect: The factory 12V outlet is off when the vehicle is powered down, meaning no current is drawn by the accessory once parked. The dash cam has been in continuous use since I purchased the vehicle without any issues; this battery drain issue began exclusively after the 68C software update. Blaming standard user accessories for the infotainment system's failure to enter sleep is unacceptable and ignores a likely software bug introduced by the 68C update. If the vehicle's electrical control modules fail to power down properly overnight, it poses unpredictable electrical and thermal risks. I escalated this issue to an FCA Case Manager, who upheld the engineer's assessment without addressing the underlying software defect. FCA has failed to perform due diligence in resolving this issue.

At highway speed, vehicle repeatedly started shaking and vibrating violently after hitting any bump or uneven portion of the roadway. Steering became extremely difficult to control and was completely useless for a period of time. A vehicle that loses the ability to steer at highway speeds puts everyone at risk of accident/death. In looking online, this has been experienced by many people and is referred to as the "death wobble". There were no warnings that this was going to occur. Vehicle has been brought to the dealership. It appears unlikely that the dealership and/or manufacturer is going to fix this problem without payment.

During a yearly safety inspection it was noted that 3 of my 4 shock absorbers are leaking and it would not pass PA safety inspection without replacement.

Ever since the 68c recall I have had a multitude of safety related issues with my vehicle. It appears that in order to protect themselves from a known faulty hybrid battery pack Jeep has reprogramed the vehicle to reduce power. While driving in electric or hybrid mode the vehicle will suddenly lose power creating an unexpected power delivery (ie. one minute you have plenty of power to pass a slower vehicle for example then all of a sudden, you lose that power mid pass). Once power loss occurs the vehicle will start acting extremely erratic with the gas engine kicking on and off and revving high for no reason, constant gear changes etc. A substantial delay occurs between pushing the gas pedal and power delivery, dramatically increasing the vehicles response time to a necessary acceleration, etc. I have inquired to my local dealership about these issues multiple times but am always told by the service advisor that they are not aware of any problems which i know is not true as the online forums are filled with hundreds of stories of near crashes, etc and that Jeep has extended the battery warranty to "unlimited" acknowledging that there is an issue. The problem is that when these batteries fail (and mine has and has been replaced) they replace them with the same defective part.

When driving the vehicle down the highway it just randomly hard shifted out of know where almost causing us to be rear-ended. The dash then said service transmission continue in drive do not shift or turn engine off until you reach a desired location. You may not be able to shift again until services. It then limited power to the vehicle. It was show codes U1003, U0101, and U0402 multiple times. The vehicle was taking to a dealer where it was "parked" only it wouldn't go into park. We had to put the e-brake up holding it in place at the dealer so it wouldn't roll. Then when attempting to shut the vehicle off it only stopped the engine from running. It stayed in ACC mode all night until the dealer could mess with it the next day. The dealer is now saying it's just a dead battery. This is unsafe and could have ended very badly just for a dead battery that showed no signs of issues before hand. For a vehicle that on has approximately 57k miles and is 4 years old this is horrible.

On 7/25/2026, the vehicle set DTC P1128 (Closed Loop Fueling Not Achieved, Bank 1) with a steady check engine light and no drivability symptoms. I cleared the code with an OBD2 scanner. My wife had driven the vehicle to a local store and back earlier with no issues. Shortly afterward, with the vehicle loaded for a trip, she applied the brakes at the end of our driveway and the vehicle did not come to a complete stop. She described the pedal response as delayed. She proceeded onto our residential street at low speed and applied the brakes again. The brakes did not function properly. The pedal traveled to the floor with minimal braking effect and the vehicle came to a rolling stop rather than a controlled stop. She pulled to the side of the street and cycled the ignition off and on. She then drove approximately 10 to 20 feet and applied the brakes again with the same result: pedal to the floor, rolling stop only. Steering effort was normal throughout. We judged the vehicle unsafe to drive and cancelled the trip. It has not been driven since. Within 10 hours of the braking failure, the vehicle experienced a complete electrical failure. The key fob would not unlock the doors and I had to use the physical key. With the brake pedal depressed and the start button pressed, the instrument cluster illuminated for less than one second and then shut off, repeating. The vehicle would not start and remains disabled. No crash, no fire, no injury. The vehicle has open safety recall 21D (NHTSA 26V-363) listed as incomplete. All other recalls were completed at dealer service in May 2026. Current mileage is ~62,000.

I have been leasing this vehicle for approximately 3 years and have experienced constant engine problems; knocking and jolting forward. There have been four safety recalls and I mentioned the engine issues at the dealership. I was told not use the electric engine and keep the car in gas mode. This has not fixed the problem; it jolts forward randomly which is very scary. I only have this one vehicle and a small child. I am not comfortable driving this car with my son in it. And now I received another recall notice for severe fire risk and no remedy available. I am making (expensive) lease payments for a car that is not safe to drive.

I am submitting this supplemental statement regarding my previously filed complaint involving a 2022 Jeep Wrangler. On November 8, 2025, I was involved in a crash that resulted in bodily injury, including head, neck, and back pain, and required post-accident inspection and towing. Despite the nature of the impact and the injuries sustained, the frontal airbag system did not deploy. The manufacturer, Stellantis, conducted an inspection through a third-party contractor and advised via email that the airbag system did not deploy because the deceleration threshold was allegedly not met. However, I have not been provided with the Event Data Recorder (EDR) data, crash pulse analysis, sensor performance evaluation, or the technical criteria relied upon to reach this conclusion. Given the vehicle damage, injuries sustained, and non-deployment of the frontal airbags, I am concerned that the airbag system may not have functioned as intended or that the deployment thresholds, sensor inputs, or system calibration may be defective or unreasonable. I respectfully request that NHTSA review this incident for potential safety defects related to airbag non-deployment, crash detection thresholds, sensor performance, or system logic in the 2022 Jeep Wrangler.

Once you get over 60 mph the car starts to shake and wobble bad feels like jeep is going to fall apart took to jeep dealer after calling 800-jeep first agent acted like never heard of it then finally confessed it’s referred to as death wobble I will not even ride my kid in jeep going on highway it’s that’s unsafe jeep said it tightened up parts but one week later still happens can’t afford to keep taking jeep in and paying to have the tighten something and week later same thing i am stuck owe money on car

The windshield on my 2022 Jeep Wrangler 4xe appears to have optical distortion that causes significant glare and visibility problems when driving in direct sunlight. The windshield is available for inspection upon request. The problem affects my ability to clearly see the roadway, traffic, and other vehicles when sunlight hits the windshield. The distortion creates a wavy or blurry appearance that can be distracting and reduces visibility, creating a potential safety hazard while driving. The condition has been reproduced and confirmed by me on multiple occasions. The vehicle was inspected by Hendrick Chrysler Dodge Jeep Ram in Wilmington, North Carolina, but warranty coverage was denied. The windshield has not been involved in an accident and there are no warning lights, messages, or other vehicle symptoms associated with this issue. The problem appears to be related to the windshield glass itself rather than any electronic system. The issue has been present for an extended period of ownership and is most noticeable during sunny conditions when light strikes the windshield at certain angles. I am filing this complaint because the visibility distortion creates a safety concern and I believe the windshield may have a manufacturing defect.

The contact owns a 2022 Jeep Wrangler. The contact stated that after using the remote starter to start the vehicle, the front window defroster was activated, and approximately 10 minutes later, the contact discovered that the front windshield had developed a 5-inch crack in the center of the windshield. The contact stated that moments later, while driving, the crack expanded to approximately 12-inches towards the driver’s side. The contact stated that the crack was in the direct field of view of the driver, creating a visibility hazard. The cause of the failure was not yet determined. The local dealer and manufacturer were notified of the failure, but no assistance was offered. The failure mileage was 22,000.

The vehicle is a Jeep Wrangler 4xe with approximately 43,000 miles experiencing a recurring electrical system malfunction involving the Body Control Module (BCM) and LIN communication network. The vehicle is currently at the dealership and is available for inspection upon request. The failure involves multiple electrical circuits and communication loss between modules, confirmed by dealership diagnostic codes including BCM B1642-15, B1646-15, B16D7-15, B16DF-15, and U1123-00 (lost communication with LIN ECU). This condition presents a safety risk due to intermittent stalling/shutdown while driving, electrical system instability, and failure of critical systems including exterior lighting and HVAC. These issues create unpredictable vehicle operation and reduced safety for occupants and others on the road. The problem has been reproduced and confirmed by the dealership over at least four separate service visits, for which documentation is available. Despite repeated repair attempts, the condition has not been resolved and the same faults continue to return. The vehicle has been inspected multiple times by the dealership. The manufacturer, Stellantis, has been contacted but has declined further escalation or engineering review, citing warranty expiration. Warning indicators, including the check engine light, have repeatedly appeared prior to and immediately after service visits. Additional symptoms include intermittent heater failure while driving, system-wide electrical malfunctions, and abnormal noises. This is an ongoing, unresolved electrical system failure involving repeated unsuccessful repair attempts and presents a continuing safety concern.

There is a confirmed recall 92A for the gear position sensor on my 2022 Jeep Wrangler. I took it to River Oaks dealership in Houston to have the recall work done in March 2024. They told me the work was complete; I returned to pick up my vehicle and found out the work had not been done because they didn't have the parts, so I took my vehicle home. I'm now told that they actually ordered the parts for the recall without telling me, and I was never informed that the parts arrived at the dealership or were going to be returned after that. I have now brought my vehicle to a different dealership (Helfman in Houston) for a repair and to have that recall fixed. They are unable to order the parts from Jeep to fix the recall, because River Oaks had previously ordered them under my VIN and have most likely returned them. No one at River Oaks is willing to help in any way. The recall manager says I should have known that they received the parts in stock after I left without any kind of notification, and the parts managers won't answer or return my calls. Jeep corporate has stated that they cannot cancel the previous parts order, but that River Oaks can cancel the previous order so that Helfman can put in a new one with my VIN. River Oaks has denied this. At this point, I cannot get a mandated safety recall fixed on my Jeep because of the previous and ongoing actions of River Oaks dealership. My options are apparently to leave it at the dealership indefinitely or take it back with a safety malfunction.

while vehicle is driving multiple dash alarms will start cycling through including stop/start, service electronic stability control, speed control messaging unavailable, service airbag system, service 4WD, engine light and ABS light, anti skid lights all come on, the speedometer goes to zero, and the power steering goes out. Driving highway speeds and suddenly having no power steering is a safety issue as well as being unsure if airbags etc are even functioning any longer. The problem has happened multiple times. The vehicle was inspected by a Jeep dealership as well as another shop in town and the codes were reproduced. They were unable to fix the issue and despite testing a "star connector" and finding it in good condition and unable to reproduce the issues were advised to replace that part anyway and see if they could reproduce the problem again at my expense. During this time the recall for 2022 Jeep Wranglers with NHTSA campaign number 26V363 came out and i requested to wait for further repair work to be done until the recall was repaired as it also relates to the power steering. I saw a fix had been published and return to the dealership to have the recall repair performed and was told that upon further inspection of the recalled part, mine passed the test, which was apparently a wiggle the wire and inspect the harness for ware only and my vehicle is no longer listed on the recall. I feel these things may still be related and I am extremely frustrated that I have a 4 year old vehicle that I am making payments on and paying insurance on that has been parked (not in my garage as it was a fire risk in the recall) and I don't feel its safe to drive and don't feel that Jeep or the local dealership are being honorable with their product.

I am filing this complaint regarding serious safety and consumer protection concerns involving my 2022 Jeep Wrangler (VIN: [XXX] ), manufactured by Stellantis, as well as issues involving the towing company E&R Towing following my accident. Prior to my accident on November 8, 2025, my vehicle experienced multiple ongoing mechanical issues, including overheating, shaking while driving, and abnormal loud noises. These issues raised serious safety concerns and were not properly resolved. On November 8, 2025, I was involved in a rollover accident. Following the accident, Stellantis initiated an investigation and retained Bosch/Engineering Analysis Associates to extract Event Data Recorder (EDR) data from my vehicle. While presented as an independent inspection, this analysis was conducted by a vendor hired by Stellantis, raising concerns about the objectivity and scope of the findings. Stellantis ultimately denied responsibility, stating that the conditions of the crash did not meet the threshold for airbag deployment. However, this conclusion fails to address the ongoing mechanical and safety issues I experienced prior to the accident, including the possibility of system or sensor malfunction. Additionally, my claim for relief under Illinois Lemon Law was denied without fully considering the pattern of defects and safety concerns. I have also filed a complaint with the National Highway Traffic Safety Administration (NHTSA), Complaint #XXX, regarding safety concerns with this vehicle. Following the accident, my vehicle was handled by E&R Towing. I have concerns regarding how my vehicle was managed after the crash, including the handling process and lack of transparency regarding procedures and fees. I am requesting that this matter be reviewed for potential violations of Illinois consumer protection laws, including unfair or deceptive practices, failure to properly address known vehicle safety issues, and improper handling of my vehicle following acciden INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT

At highway speed, vehicle repeatedly started shaking and vibrating violently after hitting any bump or uneven portion of the roadway. Steering became extremely difficult to control and was completely useless for a period of time. A vehicle that loses the ability to steer at highway speeds puts everyone at risk of accident/death. In looking online, this has been experienced by many people and is referred to as the "death wobble". There were no warnings that this was going to occur. Vehicle has been brought to the dealership. It appears unlikely that the dealership and/or manufacturer is going to fix this problem without payment.

When driving down the road my jeep goes into an uncomfortable death wobble. It has already been to a dealer to fix this once but it isn’t . There is a weld defect in the driver side front and passenger door frame . When the electronics get hot from the summer heat they black out . The digital display is not calibrated to the odometer of the vehicle . The Jeep surges violently and almost caused a collision.

I received a safety warning about my air bags specifically via my Jeep app on my iPhone about 1 1/2 hours after I had been rear-ended in a motor vehicle accident. The rear-end impact pushed me into a van in front of me. The safety notice notified me to take my 2022 Jeep in to have the air bags checked. There were no prior warnings. I am concerned as to whether or not the air bags should have employed upon impact. My seatbelt did totally lock into place after impact, but the air bags did not activate. My vehicle is currently still being repaired at a collision service, per the direction of my auto insurance carrier.

This is a RHD right hand drive Jeep . the seat belt for the driver (right side) has an "energy management loop ("rip stitching")" When the drivers seatbelt should have a "button"