2009 Lincoln Mkz

On April 18, 2018, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA) 18-002 to investigate reports of braking concerns in model year (MY) 2006-12 Ford Fusion and Lincoln MKZ, and MY 2006-11 Mercury Milan vehicles manufactured with Continental Automotive System?s ABS hydraulic control units (HCUs). Complainants report that after an ABS braking event (initiated by slippery or uneven surfaces) the brake pedal moved towards the floor and the vehicle stopping distance increased beyond driver expectations.Inside the HCU are four hydraulic normally closed (NC) valves with zinc-coated moving armatures that control the flow of brake fluid. Unstable brake fluid can degrade over time, allow the brake fluid to gel, and corrosion to form on the armatures. The high-viscosity gelation and corrosion can cause the armatures to become stuck (open). In some cases, braking returns to normal when the armature(s) subsequently become unstuck. The intermittent condition proves difficult to diagnose with complainants reporting having (non-HCU) repairs conducted only to have the condition return.During the investigation, 14 HCUs from complaint vehicles were recovered, including seven from reported crashes. NHTSA?s Vehicle Research and Test Center (VRTC) disassembled the HCUs, removed the four NC valves in each, and confirmed 22 of the 56 NC valves contained stuck armatures. On seven of the 14 HCUs, both front wheel armatures were stuck, on nine of the 14 HCUs two or three armatures were stuck. And 52 of the 56 NC armatures exhibited corrosion of the zinc coating. Forces required to extract stuck armatures from the valve sleeve were measured to range from 1.1 to 18.0 lbs. VRTC also conducted ABS braking tests on a variety of test surfaces that showed HCU failures cause increases in pedal travel and braking distances. Testing also showed that if the driver was able to apply four times the brake pedal force and two times the brake pedal travel, then high-vehicle decelerations could be achieved, however, single or multiple wheel lockups were also occurring.Based on Ford?s response to ODI?s July 20, 2018 information request letter, and complainants' reports to NHTSA, ODI identified a population of vehicles with an elevated level of field failure compared to vehicles produced both before and after.Further evaluation of Ford?s response identified that the brake fluid used to produce these vehicles, a specific formulation of a DOT3 fluid provided by CCI Corporation between February 2006 and July 2009, differed from the brake fluid used in other vehicle populations. ODI used the correlation of fluid specification and elevated field failures to identify a vehicle population exhibiting a defect trend. The complaints, crashes and injuries cited above, and the 14 recovered HCUs involve vehicles from this population.On December 18, 2019, Ford submitted safety recall (19V-904) to remedy HCU failures on the MY 2006-2010 Ford Fusion, Lincoln MKZ, and Mercury Milan vehicles manufactured with the suspect CCI brake fluid formulation. Ford will function test the HCU and replace the DOT 3 brake fluid with an improved DOT 4 brake fluid. If the HCU fails the function test, Ford will install an HCU with a different armature coating (black oxide). HCUs with black oxide coating were fully phased into Ford?s new vehicle production by MY 2016; these HCUs do not appear to be experiencing armature corrosion. ODI notes that the non-recalled EA18-002 subject vehicles, which were manufactured with a different specification brake fluid, did not display an elevated level of field failures like the recalled vehicles.Based on available information, Ford?s rec

On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.

Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show elevated rates of pedal entrapment incidents in MY 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the accelerator pedal and difficulty braking, including reports that the incident was controlled by shifting to neutral or turning the engine off. Drivers and service technicians reference observing evidence of mat interference or note unsecured Ford or aftermarket all weather floor mats in post-incident inspections.Based on information gathered during the Preliminary Evaluation the population being investigated has been narrowed to model years 2008 to 2010.This investigation has been upgraded to an engineering analysis on MY 2008 through early-2010 vehicles (produced through September 2009) to further assess the scope, frequency and safety consequences of the alleged defect.The VOQs associated with the opening of this Engineering Analysis are: 10479693, 10415911, 10379562, 10372674, 10345830, 10342572, 10339330, 10335336, 10334211, 10332233, 10331160, 10329659, 10327597, 10320011, 10232027, 10214131

Indicator light came on for passenger side airbag says it has recall and it looks as though the airbag is trying to come out of its compartment

NHTSA ID

11680810

Incident

Aug 14, 2025

The contact owns a 2009 Lincoln MKZ. The contact stated that while parked in a semi-truck parking lot, another driver was reversing where she was blocking, and the contact then attempted to avoid the collision and drive forward. The accelerator pedal was depressed however, the vehicle accelerated excessively, and the brake pedal was then depressed but failed to respond. Upon a second attempt, the brake pedal went to the floorboard, accompanied by an abnormal vibration. Consequently, the vehicle crashed into a tree. No warning lights were illuminated prior to the incident. The driver mentioned a previous incident where the vehicle reversed into a gate. The contact referenced NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic). The brakes had been checked previously and were reportedly functioning properly. During the crash, the air bags deployed, and the driver sustained a head injury but did not seek medical attention. No fire or police report was filed as the incident occurred on private property. The local dealer was contacted and mentioned an extended warranty. The dealer suggested towing the vehicle, but it was not diagnosed or repaired. The manufacturer was contacted multiple times, including their legal department, but no response was received. The failure mileage was approximately 110,000.

NHTSA ID

11678711

Incident

Jun 10, 2025

Mileage

110,000 mi

2 years ago air bags were replaced on a recall notice. Last week dash board is showing a warning notice with the air bag(s) again. Is there another recall for the air bags? Do I have to pay for replacement?

NHTSA ID

11667676

Incident

Jun 18, 2025

My MKZ suddenly cut off without warning lamps or messages at highway speed. There was a very quick shudder and all power lost. After pulling onto the road shoulder and waiting a few minutes, it restarted and drove normally. I stopped about 15 minutes later and switched it off. When returning to the vehicle, it would not start. I had it towed to a garage where it has been for 6 weeks. They have been unable to identify the problem and get it restarted. Online reports by others indicate this occurred with other Lincoln products over a span of a few years with no assistance from Lincoln/Ford to identify the problem. This is a HUGE safety issue, as well an immediate personal inconvenience.

NHTSA ID

11522508

Incident

Apr 6, 2023

Complaint Lincoln 2009 MKZ air vent grid on dash board broke in various places and collapse also, it appears the dash board in front of air vent grid is raised. Causing the defroster to not work properly and the window shield does not clear properly. I was told to fix the problem the whole dash board needs to be replaced. I see this as a design and manufacturer defect and that Lincoln should repair at no cost to Lincoln owners. Lincoln is a Luxury line this should not be happening.

NHTSA ID

11456017

Incident

Jul 10, 2020

The contact owns a 2009 Lincoln MKZ. The contact received notifications of NHTSA Campaign Numbers: 19V904000 (Service Brakes, Hydraulic) and 21V158000 (Air Bags) however, the parts to do the recall repair were not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

NHTSA ID

11455543

Incident

Mar 7, 2022

BRAKE PEDAL FAILURE 7 MONTHS AFTER BRAKE FLUID RECALL WAS DONE.

NHTSA ID

11448753

Incident

Jan 3, 2022

The Lincoln Mercury factory chrome plated rims leak air all the time making the tires low on air or flat very often! This is a very dangerous safety hazard that can cause loss of control and having an accident resulting in serious bodily injury or death! There are many numerous other Lincoln car owners that report the same symptoms and problems. The manufacturer never plated the rims properly with nickle prior to chrome plating, thus the chrome coating constantly peels off and corrodes; thus air leaks past the tire bead and the rim surface. This sounds like a giant class action lawsuit!! I am are both very upset and scared to drive under these horrific conditions, but I have no choice as news factory rims are very expensive and I cannot afford them since I am disabled and on a fixed income.

NHTSA ID

11437067

Incident

Aug 1, 2019

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

When performing any transmission fluid change or topoff involving Motorcraft® Premium ATF, MERCON® V has replaced all versions of Motorcraft® Premium ATF and can be used going forward. Mixing Motorcraft® Premium ATF and MERCON® V in the same transmission is acceptable. After 31-Jan-2024, Motorcraft® Premium ATF will no longer be manufactured and will only be available until inventory depletes.

Certain 2005-2014 Mustang, 2005-2006 GT, 2004-2011 Ranger, 2006-2012 Fusion and MKZ/Zephyr, 2006-2011 Milan, and 2007-2010 Edge & MKX Vehicles Driver & Passenger Airbag Module Quality Control Inspection REASON FOR THIS SUPPLEMENT • Updated Ranger Technical Information to include images of a pass and fail airbag inflator inspection for 2007-2011 model years.

Certain 2005-2014 Mustang, 2005-2006 GT, 2004-2011 Ranger, 2006-2012 Fusion & MKZ/Zephyr, 2006-2011 Milan, and 2007-2010 Edge & MKX Vehicles Driver & Passenger Airbag Module Quality Control Inspection: Ford Motor Company has determined that some vehicles claimed by dealers as repaired under Takata Airbag Safety Recalls 15S21, 17S42, 18S02, 19S01, and 21S12 may not have received the claimed repairs. The propellant in certain Takata airbag inflators can experience an alteration over time with exposure to certain climate conditions. A combination of time, high temperature fluctuations, and humidity contribute to the degradation of the propellant in the inflators. This degradation can cause the propellant to burn too quickly, creating high pressure inside the inflator, and in extreme cases causing the inflator to rupture in the event of a crash necessitating airbag deployment. A ruptured inflator can send inflator parts toward vehicle occupants resulting in serious injury or death. Additional information regarding Takata recalls can be found at www.nhtsa.gov and www.safercar.gov.

Certain 2006-2010 Model Year Fusion/Milan/MKZ/Zephyr Vehicles Equipped with Anti-Lock Brake Systems DOT 3 Brake Fluid and Anti-Lock Brake System Function In some of the affected vehicles, customers may return to the dealer with complaints of extended brake pedal travel after either 19S54 or 20S14 was previously performed and the program is closed