2011 Mazda Mazda6 Problems

The contact owns a 2011 Mazda Mazda6. The contact stated that while driving at 25 MPH, the contact attempted to swerve out the way of another vehicle as she suddenly lost control of the vehicle. Due to the failure, the contact force to steer the vehicle to the left as the contact attempted to maintain control of the vehicle. The contact managed to pull over into a parking lot and called her husband for assistance. Despite the failure, the contact managed to drive the vehicle home despite the vehicle being extremely difficult to maneuver. The contact's husband managed to drive the vehicle to a local mechanic, who determined that the front subframe had failed due to excessive corrosion of the subframe. The mechanic then informed the contact of NHTSA Campaign Number: 19V323000 (Structure, Suspension); however, the contact was informed that her vehicle was not included in the recall. The manufacturer was notified of the failure where they confirmed that the vehicle was not included in the recall. The vehicle remained in the mechanic's possession and had yet to be repaired. The failure mileage was 115,000.

2011 Mazda6 A serious safety defect occurred on my vehicle and matches NHTSA Recall 19V-323 / Mazda Recall 2818I (front cross member corrosion due to insufficient coating) despite this recall not being associated with my VIN. Front cross member cracked due to rust, causing loss of steering control, wheel misalignment, and scraping from the front wheel. This is exactly the failure described in the recall (breakage of the cross member and reduced steering control, increasing the risk of a crash). My safety and the safety of others were put at risk. Although my VIN is not currently associated with the recall, all conditions of the recall apply to my vehicle: -2011 Mazda6 within the affected production range -Defect is a manufacturing issue (insufficient paint coating) -Vehicle was registered in Missouri from 2023-2025, which is a listed state The only reason this recall was not associated with my VIN is because the vehicle was not registered in Missouri at the exact time of the 2019 recall campaign. This is an administrative gap, not a safety distinction. It should not be allowed to limit a manufacturer safety defect to specific states. Vehicles move across state lines constantly. A defect that causes loss of steering control does not stop being dangerous when a car crosses a border. Registration records alone did not reflect actual vehicle use or risk. If recalls are state-limited, manufacturers and NHTSA must continue tracking registration changes and associate the recall with the VIN as soon as a vehicle becomes registered in an affected state. Rust is progressive and age-related. Since this recall began in 2019 and it is now 2026, affected vehicles are more likely to experience failure, and many are now registered in different states than they were in 2019. I am requesting that NHTSA associate Recall 19V-323 with my VIN, investigate the adequacy of state-limited recall tracking, and take action to prevent this known safety defect from causing additional crashes.

The contact owns a 2011 Mazda Mazda6. The contact stated that while driving at an undisclosed speed and coming to a stop, the steering wheel was not operating properly. Several days later while the contact's wife was driving at an undisclosed speed, there was play in the steering wheel. Additionally, there was an abnormal sound coming from the passenger’s side wheel. The contact stated that the wheel was turning abnormally. A mechanic arrived at the residence to diagnose the vehicle and determined that the sub frame was rusted. While touching the sub frame, pieces of the sub frame fractured. The dealer was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 92,000.

The contact owns a 2011 Mazda Mazda6. The contact stated that while driving at 25 MPH, the contact attempted to swerve out the way of another vehicle as she suddenly lost control of the vehicle. Due to the failure, the contact force to steer the vehicle to the left as the contact attempted to maintain control of the vehicle. The contact managed to pull over into a parking lot and called her husband for assistance. Despite the failure, the contact managed to drive the vehicle home despite the vehicle being extremely difficult to maneuver. The contact's husband managed to drive the vehicle to a local mechanic, who determined that the front subframe had failed due to excessive corrosion of the subframe. The mechanic then informed the contact of NHTSA Campaign Number: 19V323000 (Structure, Suspension); however, the contact was informed that her vehicle was not included in the recall. The manufacturer was notified of the failure where they confirmed that the vehicle was not included in the recall. The vehicle remained in the mechanic's possession and had yet to be repaired. The failure mileage was 115,000.

I WAS IN A CRASH WHERE MY FRONT END WAS EASILY DAMAGED AND PASSENGER AIR BAGS NOT DEPLOYED

HAD AN HEAD ON CAR ACCIDENT ON THE STREET MY TIRE BLOW OUT AND HIT A LIGHT POLE. THE PASSENGER AIR BAG DID NOT COME OUT, ALSO THE DRIVER AIRBAG CAME OUT BUT IT WAS DEFLATED NO AIR WAS IN IT OR WHAT EVER MAKES AN AIR BAG BLOW UP. IN WHICH COST ME TO HIT MY HEAD ON THE STEERING WHEEL.

2011 Mazda6 A serious safety defect occurred on my vehicle and matches NHTSA Recall 19V-323 / Mazda Recall 2818I (front cross member corrosion due to insufficient coating) despite this recall not being associated with my VIN. Front cross member cracked due to rust, causing loss of steering control, wheel misalignment, and scraping from the front wheel. This is exactly the failure described in the recall (breakage of the cross member and reduced steering control, increasing the risk of a crash). My safety and the safety of others were put at risk. Although my VIN is not currently associated with the recall, all conditions of the recall apply to my vehicle: -2011 Mazda6 within the affected production range -Defect is a manufacturing issue (insufficient paint coating) -Vehicle was registered in Missouri from 2023-2025, which is a listed state The only reason this recall was not associated with my VIN is because the vehicle was not registered in Missouri at the exact time of the 2019 recall campaign. This is an administrative gap, not a safety distinction. It should not be allowed to limit a manufacturer safety defect to specific states. Vehicles move across state lines constantly. A defect that causes loss of steering control does not stop being dangerous when a car crosses a border. Registration records alone did not reflect actual vehicle use or risk. If recalls are state-limited, manufacturers and NHTSA must continue tracking registration changes and associate the recall with the VIN as soon as a vehicle becomes registered in an affected state. Rust is progressive and age-related. Since this recall began in 2019 and it is now 2026, affected vehicles are more likely to experience failure, and many are now registered in different states than they were in 2019. I am requesting that NHTSA associate Recall 19V-323 with my VIN, investigate the adequacy of state-limited recall tracking, and take action to prevent this known safety defect from causing additional crashes.

Alignment is off. Recall for my type of call for the control arm weakening and causing wheel alignment problems. Why isn't mine part of recall??

The headlights are increasingly failing. They are so dim that i can not safely drive at night. They burn out easily. I have to replace them about 4 times a year now. In the first few years of owning the car the headlights were fine. But now it is a major safely issue for myself and others on the road. It seems like with age the headlights or components are wearing out. I am considering getting rid of this car only due to the headlights. I have considered changing to a xenon system but i am scared of the wiring and do not want to risk a wiring issue. This is my only concern with this car and it appears that most who have the same car have the same headlight issue. This should be recalled to save lifes! It is dangerous to drive this car at night with such poor lighting.

HEADLIGHT ON BOTH SIDES GO OUT OFTEN. AFTER HAVING THIS ISSUE FAR TOO MANY TIMES, I LOOKED ONLINE HOPING TO FIND A SOLUTION AND DISCOVERED MULTIPLE MAZDA OWNERS ARE HAVING SAME PROBLEM. ITS A MALFUNCTION IN THE MAZDA THAT NEEDS TO BE FIXED BY MAZDA THIS HAPPENED EVER SINCE I BOUGHT THE CAR IN 2011 I HAD TO REPLACE THE HEADLIGHT BULBS TWICE A YEAR AT LEAST .

HEADLIGHT ON BOTH SIDES GO OUT OFTEN. AFTER HAVING THIS ISSUE FAR TOO MANY TIMES, I LOOKED ONLINE HOPING TO FIND A SOLUTION AND DISCOVERED MULTIPLE MAZDA OWNERS ARE HAVING SAME PROBLEM. ITS A MALFUNCTION IN THE MAZDA THAT NEEDS TO BE FIXED BY MAZDA THIS HAPPENED EVER SINCE I BOUGHT THE CAR IN 2011 I HAD TO REPLACE THE HEADLIGHT BULBS TWICE A YEAR AT LEAST .

ALARM GOES ON INTERMITTENTLY WHILE CAR IS PARKED. THIS STARTED IN FEBRUARY, 2020 AND HAS CONTINUED TO THE PRESENT. *TR

PASSENGER SIDE DASHBOARD IS GETTING A STICKY SURFACE ON TOP. THE TOP LAYER ALMOST SEEMS LIKE IT IS MELTING. IT IS JUST STARTING TO GET STICKY AND IT IS JUST ON TOP. THE STICKINESS HAS JUST STARTED IN THE LAST 2 WEEKS. THE STICKY SURFACE IS CAUSING A GLARE AND IS AFFECTING THE VISIBILITY WHEN DRIVING. FURTHER, THE DASHBOARD CRACKED ALL THE WAY DOWN AFTER HAVING THE AIR BAG REPLACED DUE TO THE RECALL. NO PRESSURE/DAMAGE/HITS HAS OCCURRED ON THE DASHBOARD BY CONSUMER AND YET IT CRACKED ALL THE WAY DOWN IN JANUARY 2018.

THE LOW BEAM HEADLIGHT BULBS GO OUT AFTER LESS THAN A YEAR. SOMETIMES THEY WILL START WORKING AFTER HITTING THE HEADLIGHT ASSEMBLY ON THE OUTSIDE OF THE CAR.

TAKATA INFLATORS. MAZDA RECALL #: 7214C NHTSA RECALL #: 14V114000 I WAS NEVER NOTIFIED OF THE FUEL TANK RECALL AND NOW IT IS CLOSED.

I HAVE HAD AN ONGOING ISSUE SINCE I PURCHASED MY MAZDA 6 2011, IF I SLOW DOWN OR STOP FOR A TRAFFIC LIGHT AND THEN TRY TO ACCELERATE THE GAS PEDAL IS TO THE FLOOR AND THE CAR DOESN'T MOVE, THEN OUT OF NOWHERE IT WILL ACCELERATE. I WAS TOLD THE VOLTAGE IN THE GAS PEDAL CENSOR AND THE CENSOR IN THE ENGINE WERE NOT THE SAME VOLTAGE, BOTH WERE REPLACED BUT I STILL CONTINUE TO HAVE PROBLEMS AND THE DEALERSHIP CANNOT FIND OUT WHAT THE PROBLEM IS. MY CAR HAS BEEN BACK IN TO MAZDA 3 TIMES BUT NO SOLUTION, AS THIS IS EXTREMELY DANGEROUS IN HEAVY TRAFFIC I WISH SOMEONE COULD FIGURE THIS OUT BEFORE I GET INTO A SERIOUS ACCIDENT. *TR

I WAS ON A STREET IN THE CITY WAITING FOR THE LIGHT TO CHANGE. SUDDENLY I LOST CONTROL OF THE CAR, THE CARD ACCELERATED HIMSELF. I TRY TO AND PUT BRAKE TO THE BOTTOM BUT ANYWAY I HIT THE CAR IN FRONT OF ME. MUCH OF THE FRONT OF MY CAR IS BROKEN. THE OTHER CAR WAS DAMAGED IN THE BACK OF THEIR CAR. THE POLICE MADE A REPORT OF WHAT HAPPENED.

WAS DRIVING ON INTERSTATE AT 70MPH AND APPLIED BREAKS, HEARD A BANG FROM AREA OF PASSENGER FRONT SIDE AND LOST CONTROL OF THE STEERING OF THE VEHICLE CAUSING IT SWERVE INTO THE ADJACENT LANE ON MY RIGHT. I NARROWLY AVOIDED BEING HITTING AND BEING HIT BY OTHER VEHICLES AND WAS ABLE GET THE CAR TO THE SHOULDER EVENT WITHOUT HAVING PROPER CONTROL STEERING AS THE CAR WOULD ONLY STEER TO THE RIGHT. UPON INSPECTING THE VEHICLE IT WAS DISCOVERED THAT THE BANG WAS THE PASSENGER SIDE SUBFRAME CRACKING DUE TO HEAVY DETERIORATION FROM RUST. THE CAR IS UNDERIVABLE. I CONTACTED MAZDA AND DISCOVERED THAT THE PREVIOUS YEARS OF THIS MODEL HAVE A RECALL FOR THIS SUBFRAME DETERIORATION ISSUE FOR THE SAME EXACT PART #. I WAS ALSO INFORMED THAT THE CAR CANNOT BE FIXED AS BECAUSE OF THE PART # IS NOT AVAILABLE AND HAS/IS ON BACKORDER FOR MANY MONTHS. THIS DEFECT IS A HUGE SAFETY RISK, IN MY CASE I AM VERY LUCKY THIS DID NOT RESULT IN FATAL ACCIDENT TRAVELING AT 70MPH ON INTERSTATE 80. I FEAR OTHER MIGHT NOT BE SO LUCKY. THE SUBFRAME RECALL MOST CERTAINLY NEEDS TO BE EXPANDED TO AT LEAST 2011 AND SUBSEQUENT YEARS THAT USE THIS SAME SUBFRAME. ADDITIONALLY, AT MINIMUM COURTESY TO IT CUSTOMERS MAZDA SHOULD BE ALTERING ITS CUSTOMERS TO HAVE THEIR SUBFRAMES INSPECTED AS THIS IS A VERY DANGEROUS SITUATION WITH MANY VEHICLE OWNERS UN AWARE THEY ARE DRIVING TICKING TIME BOMBS WITH SUBFRAMES THAT ARE DETERIORATING PREMATURELY AND CAN LOSE CONTROL OF STEERING AT ANY MOMENT.

Rear CONTROL ARM broke off the REAR SUBFAME due heavy RUST. I had to replace the entire rear subframe plus both control arms. This incident occurred WHILE I WAS DRIVING! Now I find out that the front end is shot as well and that Mazda is only recalling the front subframe and not the rear and I want to know why. Somebody could have been killed. The repair cost me $700 plus rental fees for a vehicle. I had my vehicle in the shop for 16days. It cost me $1,135. I have the invoices.

THE 2011 MAZDA 6 HAS A HARD SHIFT FROM 1ST TO 2ND GEAR LEADING TO A HARD JERK TO ALL PASSENGERS. THE CAR SEEMS TO JUMP AT TIMES OR FEELS LIKE SOME ONE HIT IT FROM THE BACK. I HAVE CHECKED ONLINE, AND IT SEEMS TO BE A PROBLEM WITH MANY MAZDA 6. *TR

VEHICLE HAS A 3.7L V6 DURATEC ENGINE DESIGNED BY FORD. I WAS ENTERING THE HIGHWAY AT ABOUT 55MPH, CHECK ENGINE LIGHT WENT ON, THEN VEHICLE SHUT OFF, AND I LOST BOTH POWER AND STEERING. WAS ABLE TO GET TO SIDE OF THE HIGHWAY WITHOUT CRASHING. STEAM/SMOKE WAS COMING OUT OF THE HOOD AND THE TEMP GAUGE WAS PINNED AT H. DEALERSHIP ADVISED THAT COOLANT HAD GOTTEN MIXED WITH OIL AND ENGINE WAS DESTROYED. COST TO REPAIR - $7400 USED $13K NEW ENGINE. TOLD IT WAS NOT DUE TO ANY NEGLECT OR MAINTENANCE ISSUE. IT WAS A WATER PUMP FAILURE. THERE IS A DESIGN FLAW IN THIS ENGINE. THE WATER PUMP IS INTEGRATED INTO THE ENGINE AND TIMING CHAIN. WHEN THE PUMP FAILS IT DAMAGES THE ENGINE, ALLOWING COOLANT TO MIX WITH THE OIL. NUMEROUS FORD AND MAZDA OWNERS HAVE HAD THIS PROBLEM BUT BECAUSE IT USUALLY HAPPENS AT OR AFTER 100K MILES THE MANUFACTURERS DO NOT REPORT IT. THEY WILL ALSO DO NOTHING TO HELP THE CUSTOMER WHO IS LEFT WITH A HUGE REPAIR BILL OR A TOTALED CAR. PLEASE HELP ME AND OTHER OWNERS. I HAVE RESEARCH WITH THE NAMES OF OTHER OWNERS WHO HAD THE SAME PROBLEM WITH THEIR FORD OR MAZDA.

THE AC COMPRESSOR CLUTCH LOCKED UP AND CAUSED THE BELT TO MAKE LOUD SCREECHING NOISES. ALSO, SOMETHING BURNING COULD BE SMELLED INSIDE THE ENGINE AND BURNT RUBBER WAS FLUNG AROUND THE ENGINE COMPARTMENT. ANOTHER ISSUE: READ ABOUT THIS A LOT BECAUSE I AM EXPERIENCING IT, THE PASSENGER-SIDE DASH IS MELTING. SEEMS THEY USED A CHEAP MATERIAL AND WHEN IT GETS ABOVE 80 DEGREES OUTSIDE THE DASH BEGINS TO MELT. IT IS STICKY, LEAVES A RESIDUE ON YOUR FINGERS, AND PRODUCES AN EXTREME GLARE. THE AC WENT OUT WHILE I WAS IN THE DRIVE-THROUGH ORDERING FOOD. THE DASH BOARD HAS BEEN MELTING SINCE LAST SUMMER AND HAS NOT GOTTEN ANY BETTER. STOPPED MELTING DURING THE WINTER AND BEGAN MELTING NOW THAT IT'S SUMMER AGAIN.

TL* THE CONTACT OWNED A 2011 MAZDA 6. WHILE THE VEHICLE WAS SHIFTED INTO REVERSE, IT ACCELERATED ON ITS OWN. THE BRAKE PEDAL WAS ENGAGED, BUT THE VEHICLE CONTINUED TO ACCELERATE AND CRASHED INTO THE GARAGE DOOR. THE DRIVER SUFFERED INJURIES TO THE RIGHT ARM THAT REQUIRED MEDICAL ATTENTION. A POLICE REPORT WAS FILED. THE VEHICLE WAS DESTROYED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 50,000.

TAKATA RECALL - 2011 MAZDA 6 I WAS THE PASSENGER IN A COLLISION IN NOVEMBER 2015 WHERE THE 2011 MAZDA 6 WAS T-BONED ON THE DRIVER'S SIDE BY ANOTHER VEHICLE (FORD FUSION), WHICH MADE THE MAZDA 6 SPIN SEVERAL TIMES, HOP A CURB, AND DEPLOY THE AIRBAGS. AS THE PASSENGER (FRONT SEAT) I SUFFERED INJURIES CAUSED BY THE TAKATA AIRBAGS AND REQUIRED GOING TO THE HOSPITAL FOLLOWING THE COLLISION. INJURIES INCLUDED AT LEAST THREE FRACTURED/BROKEN RIBS AND MAJOR BRUISING ON MY RIGHT KNEE. INJURIES TOOK OVER 6 MONTHS TO HEAL, TAKING HEAVY DOSES OF PAIN KILLERS JUST TO MANAGE THE PAIN. LINGERING EFFECTS FROM THIS COLLISION CAN STILL BE FELT 7 MONTHS LATER. THE DRIVER DID NOT SUSTAIN MAJOR INJURIES ASIDE FROM SCRAPES AND A FEW BRUISES. POLICE REPORTS DETERMINED THAT THE DRIVER OF THE FORD FUSION WAS RESPONSIBLE FOR THE COLLISION AND WAS CHARGED WITH CARELESS/RECKLESS DRIVING. THAT DRIVER FAILED TO STOP/YIELD IN THEIR TURNING LANE BEFORE DRIVING STRAIGHT INTO THE MAZDA 6. THE MAZDA 6 WAS DECLARED TOTALED BY INSURANCE. THE MAZDA 6 WAS ADDED TO THE TAKATA AIRBAG RECALL IN MAY 2016, APPROXIMATELY 6 MONTHS AFTER THE ACCIDENT HAD OCCURRED.

Car developed a known recall issue problem, Recall 2818I. Even though Nebraska was not listed as a "salt state", it's obvious that Nebraska has similar conditions to Iowa. Attempts to contact Mazda USA corporate would not even fix the issue, citing cars age and other factors even though the damage is very specific to this particular recall.