2021 Mercedes-Benz A 220

this is a formal notification regarding my vehicle that I purchased at House Of Imports on February 27, 2021. A Mercedes Benz A-Class 220 year 2021, VIN #W1K3G4EB7MJ290124. Shortly after purchase I experienced several safety concerns about the vehicle. The first and main concern are while driving vehicle the accelerator stopped working ,vehicle would not move forward or back which put my life in a dangerous situation due to this isssue that occured while on a main street with incoming traffic. Immediately I made an a report with dealer and car was taken to dealership ( House Of Imports) . The advisor told me it was a software issue and they updated the system which they said vehicle will not have that issue again. Several things were replaced which ai have the repair documents. The second issue with the vehicle was about 3 weeks from this date today I turned on my vehicle to exit my garage I put the gear on Reverse and it did not move , I tried to move thr car forward meaning putting the gear on Drive and still nothing happened, after several attempts nothing happened. I decided to turn off the vehicle and a few hours later turned it back on and I was able to drive. The third issue was just last week January 19, 2026 I turned on vehicle to exit my garage and again the car would not move back or forward. I tried changing gears multiple times for about 20 minutes but car never moved it seemed completely stuck. The following day I had to get the car towed to House Of Imports, and it has been at dealer since then. Due to this situation I no longer feel safe driving the vehicle, I don't consider the vehicle is in proper safety functioning condition and it's not corresponding to the value paid. For this matter I respectfully request an immediate solution.

NHTSA ID

11714047

Incident

Jan 19, 2026

While driving my lease vehicle on two separate days, it completely shut down while in motion with no prior warning. The first incident occurred while crossing a MAX train intersection in downtown Portland. The engine stopped mid intersection, emitted a strong mechanical odor, ticking noises began, and dashboard alerts appeared. I could not restart or shift the vehicle into neutral. It was stuck, blocking the intersection. Although hazard lights were flashing, the vehicle appeared completely undamaged, so other drivers didn’t realize it was disabled. Police were called to the scene, and we had to remain alert for oncoming trains and traffic weaving around us. Four days later, while driving about 30 MPH on Murray Boulevard near Cornell Rd, a 4-lane hwy near a freeway off-ramp the car failed again in the exact same way. The engine shut down in active traffic. The smell, ticking sounds, and dashboard messages all returned. The vehicle once again would not shift into neutral or respond to restarts. This failure happened with traffic traveling 30-45MPH. Despite police presence and hazard lights, multiple near-accidents occurred because the vehicle looked fully intact and other drivers didn’t understand it was inoperable. Mercedes-Benz claimed this was a starter motor issue, which is inaccurate. A starter motor does not cause a moving vehicle to shut off, nor does it lock out neutral. These symptoms point to a critical failure of the powertrain or electrical system. Most alarming is the inability to manually override the system and move the vehicle to safety. Bystanders and even police were unable to shift or push it. This is a serious design flaw that turns a technical malfunction into a dangerous roadside emergency. This vehicle was in pristine condition with no damage or misuse. I kept up with all maintenance and care. Technology should never prevent human intervention during failure. These incidents placed lives at serious risk.

NHTSA ID

11660206

Incident

Apr 28, 2025

Rear view camera says it is inoperative when I put it in reverse. I understand that a number of Mercedes models have been recalled due to a software issue but the dealer tells me my car is not on the list. The problem I have is identical to the other models. My car should be on the list

NHTSA ID

11590984

Incident

May 21, 2024

there’s a recall, and I need it fixed asap, i called mercedes and they said they don’t know when they’ll be able to do it, that it could take “years” ??????

NHTSA ID

11500556

Incident

Dec 29, 2022

The driver’s seatbelt failed to properly engage during a high-speed rear-end collision allowing his head and face to strike the steering wheel causing a loss of consciousness and other symptoms of traumatic brain injury. Thus far the problem has not been reproduced or confirmed by a dealer but it is believed the seat belt was inspected by EMTs responding to the scene. Additional documentation will be provided when received. There were no warnings or other symptoms of the problem prior to the failure. This report is filed on behalf of the owner and driver by their attorney.

NHTSA ID

11494675

Incident

Nov 13, 2022

Traveling at 65 MPH in the right-hand lane * Driving Assistance ON * Traffic Sign Assist ON * Speed Limit Adoption ON Staying in the right-hand lane, I pass by an offramp Sudden deceleration to 20 MPH – Phantom braking This has happened twice traveling past the same offramp. Since, I have turned the Speed Limit Adoption OFF Note that this particular off ramp has more than one speed limit sign (yellow) visible from the freeway. My guess is that the Mercedes is reading the off ramp signs and interpreting them to be for the freeway and not for the off ramp. I consider the sudden deceleration to be dangerous

NHTSA ID

11453148

Incident

Feb 20, 2022

The contact owns a 2021 Mercedes Benz A220. The contact stated while reversing the vehicle, the rearview camera screen was blank. The contact stated that there was no warning light illuminated. The contact took the vehicle to the local dealer and was made aware that NHTSA Campaign Number: 21V354000 (Back Over Prevention, Electrical System) was associated with the VIN. The dealer informed the contact that she was added to the waiting list. The vehicle was not repaired but was pending repairs. The manufacturer had been informed of the failure. The failure mileage was approximately 10,000.

NHTSA ID

11432378

Incident

Aug 4, 2021

Mileage

10,000 mi

The contact owns a 2021 Mercedes Benz A220. The contact received notification of NHTSA Campaign Number: 21V354000 (Electrical System) however, the part to do the recall repair was not yet available. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact experienced the failure listed in the recall. Parts distribution disconnect.

NHTSA ID

11432005

Incident

Mar 1, 2021

This NCU replaces the prior NCU issued on May 15, 2025, and contains additional MY 2023 and MY 2024 vehicles which are highlighted below. In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (“MBUSA”) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (“MY”) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: •Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (‘MIL’).

Complaint Hand detection system – malfunction / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" "Active steering assist not available" Cause Possible causes: Hand detection mat, hand detection control unit, contacts, and electrical feed line. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Check: Please do not replace the HOSWD control unit. Please flash the new SW and perform the SCN coding for the HOSWD control unit (N179/1) (available from July 2026). The software can be flashed onto all HOSWD213 with HW number A0009011522 and all HOSWD223 with HW number A0009011422. Please also flash the SW for the IDC control unit (N62/4), if possible (only applies to HOSWD223). Erase fault memory Remedy: Turn on the ignition or start the engine without touching the steering wheel. If, after 10 seconds without touching the steering wheel, one of the three fault messages appears on the instrument cluster: Check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, crimp connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage -> replace the steering wheel rim. If a yellow message does not appear on the instrument cluster within 10 seconds: Grasp the steering wheel fully with both hands, including the chrome molding at the 6 o'clock position (see picture 1). If the fault is triggered by grasping the steering wheel rim or pressing the clip at the 6 o'clock position, check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, kinked connections, loose connections, etc. (example in picture 2 and 3). Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage: Replace the steering wheel rim. Please do not replace the HOSWD control unit. A TIPS case should be created if fault profile is unclear. In the event of a customer complaint and a further fault code in HOSWD: B1E7713: Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). B1F1F04: Check the control unit of the hand detection system; if necessary, replace this with the control unit from a donor vehicle (make sure that the hardware part numbers are identical).

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 9, 2026. After July 9th, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.

Complaint Service code B1 displayed in the customer menu does not match the workshop code displayed in the workshop menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.