2001 Mercedes-Benz E320

Unknown, the car filled with smoke from within the dashboard on driver side.

NHTSA ID

11459312

Incident

Apr 2, 2022

TL* THE CONTACT OWNS A 2001 MERCEDES-BENZ E320. THE CONTACT STATED THAT WHILE DRIVING AT 55 MPH, THE PASSENGER'S SIDE AIR BAG AND SIDE CURTAIN AIR BAGS INADVERTENTLY DEPLOYED WITHOUT WARNING OR IMPACT. THE CONTACT PULLED OFF TO THE SHOULDER TO INSPECT THE VEHICLE AND SAW THAT THERE WAS NO DAMAGE TO THE VEHICLE. A POLICE REPORT WAS NOT FILED. THE CONTACT HAD NOT SUFFERED INJURIES. THE CONTACT DROVE THE VEHICLE HOME AFTER THE FAILURE. MERCEDES-BENZ OF BELLEVUE (11850 BEL-RED RD, BELLEVUE, WA 98005) WAS CONTACTED AND THE CONTACT WAS INFORMED THAT AN INVESTIGATOR WOULD CONTACT HIM TO DISCUSS THE FAILURE. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 231,000.

NHTSA ID

11389752

Incident

Jan 23, 2021

Mileage

231,000 mi

TL* THE CONTACT OWNS A 2001 MERCEDES-BENZ E320. THE CONTACT STATED THAT THE SUN ROOF SEAL DISINTEGRATED AND CAUSED WATER TO LEAK INTO THE VEHICLE. THE CONTACT STATED THAT HIS 2008 MODEL VEHICLE WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 19V918000 (VISIBILITY) HOWEVER, THE 2001 VIN WAS NOT INCLUDED. THE CONTACT CONTACTED MERCEDES-BENZ OF FORT LAUDERDALE LOCATED AT 2411 S FEDERAL HWY, FORT LAUDERDALE, FL 33316; (954) 949-0623) AND IT WAS CONFIRMED THAT THE FAILURE WAS THE SAME HOWEVER, THE 2001 MODEL WAS NOT INCLUDED IN THE RECALL. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 360,000.*LN*JB

NHTSA ID

11377432

Incident

Dec 1, 2015

Mileage

360,000 mi

SRS LIGHT APPEARS ON DASHBOARD. CAR WAS CHECKED IN A REPAIR SHOP. DIAGNOSTICS INDICATE A CODE WHICH HAD RECALL ISSUES. I CALLED A MERCEDES DEALER TO DISCUSS THE PROBLEM BUT WAS TOLD THERE WAS NO RECALLS ON THIS. WHAT IS TO BE DONE WHEN AN ACCIDENT HAPPENS? THIS IS A SAFETY ISSUE!!

NHTSA ID

11183309

Incident

Dec 26, 2018

ENGINE CAUGHT ON FIRE WHILE VEHICLE WAS IDLING IN PARK IN THE DRIVEWAY. COMPLETELY DESTROYED THE VEHICLE IN 10-15 MINUTES. FIRE STARTED UNDER THE HOOD. I BELIEVE THAT THERE WAS AN ELECTRICAL PROBLEM THAT INDUCED THE FIRE BUT UNABLE TO BE SURE. PHOTOS ARE AVAILABLE IF NEEDED. THE CAR WAS IN GOOD MAINTENANCE, NO ENGINE WORK HAD BEEN DONE RECENTLY. LAST REPAIR WAS A TRANSMISSION FLUID REPLACEMENT AFTER REPAIRING A TRANSMISSION FLUID LEAK IN EARLY DECEMBER 2018

NHTSA ID

11174621

Incident

Jan 26, 2019

Mileage

150,000 mi

IGNITION AND KEY DEFECTS CAUSES CAR TO STOP RUNNING AND STALL. STEERING WHEEL LOCKS WHILE CAR IS IN MOTION.

NHTSA ID

10915715

Incident

Oct 7, 2016

Mileage

153,769 mi

WHEN VEH. IS STOPPED AT A LIGHT OR JUST IN A PARKING LOT, IT STALLS OR WILL NOT START RIGHT AWAY. EVENTUALLY IT STARTS AND AWAY WE GO. NEVER A WARNING WHATSOEVER. ALL FLUIDS ARE FULL AND BATTERY IS GOOD. REC. FUEL(GAS) IS ALWAYS USED.

NHTSA ID

10824424

Incident

Feb 4, 2016

DEFECTIVE INSULATION ON THE WIRING FOR THE EXTERIOR LIGHTING. IT APPEARS THIS PROBLEM IS CATALYZED BY HEAT. INSULATION CRUMBLES AND LEAVE BARE WIRE EXPOSED, CAUSING SHORTAGE AND FAILURE/MELTING OF LIGHT SOCKET. OBVIOUSLY, MERCEDES BENZ OF NORTH AMERICA REALIZED ISSUE BUT S NOT COMPELLED TO MAKE REPAIRS!

NHTSA ID

10749075

Incident

Aug 17, 2015

Mileage

200,000 mi

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions.

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.

Complaint Vehicle with atypical reduced heat output. Cause Silicate granulate may have escaped from a damaged bag in the expansion reservoir (not visible), reducing the coolant flow in the heater heat exchanger (see picture). Remedy With the aforementioned complaint, make sure that the cooling circuit is inspected for silicate residues after all standard tests are completed. The silicate residues tend to accumulate upstream of the shutoff valve for the heater hot water pulsed valve. If there are silicate residues in the coolant, the engine must be flushed thoroughly. To make sure that all silicate residues are removed from the cooling circuit, the following parts must also be replaced (cleaning of these components is not sufficient): Coolant expansion reservoir, radiator, oil/water heat exchanger (oil cooler), heater valve, heat exchanger of heater, coolant and, if installed, the electric water pump for the residual heat utilization system. Determine the parts for the respective vehicle in the EPC.

Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).