2012 Mercedes-Benz E550

On April 10, 2020, NHTSA's Office of Defects Investigation (ODI) received a defect petition from Mr. Surjit Singh alleging premature corrosion of the rear brake lines in his 2013 Mercedes-Benz E350 sedan. The petitioner states that he was recently informed by a Mercedes dealer service department that his car had severely rusted brake lines that need[ed] to be replaced immediately at a cost of about $3300. He further stated that the dealer service advisor informed him that he had seen the issue on many cars like his. The petitioner requested ?that NHTSA launch an investigation into this serious issue of rusting brake lines on [his] 2013 Mercedes E350.? The brake line corrosion reported by the petitioner did not result in brake line leakage or any compromise in brake system performance before it was detected in a dealer vehicle inspection. The petitioner submitted a complaint to NHTSA documenting his experience (NHTSA ID 11319024).On April 24, 2020, ODI opened Defect Petition DP20-004 to evaluate the petitioner?s request. ODI conducted a search for all consumer complaints and Early Warning Reporting (EWR) data related to allegations of brake line corrosion or leakage in 2013 Mercedes-Benz E350 sedans and similarly equipped vehicles. The 2013 E350 is a fourth-generation Mercedes-Benz E-Class vehicle (W212 platform), which was first sold in the United States in 2009 as a 2010 model. Mercedes-Benz sold approximately 245 thousand model year 2010 through 2015 E-Class sedan and wagon vehicles in the United States with the same brake line design as the petitioner?s vehicle.ODI?s search for complaints and EWR data in 2013 Mercedes E350 vehicles found no additional records related to the alleged defect. Expanding the search to all W212 platform vehicles identified just one incident, a complaint alleging unspecified brake line corrosion and leakage in a 2011 Mercedes-Benz E550 (NHTSA ID 10902081). The complaint did not allege that the brake line leakage resulted in reduced brake performance, crash, or injury. The resulting failure rate of 0.4 failures per hundred thousand vehicles is extremely low for a population that includes vehicles that have been in service for over ten years. After reviewing the available data, ODI has not identified evidence of a defect trend in the subject E-Class vehicles that would support opening a defect investigation into premature brake line corrosion failure. NHTSA is authorized to issue an order requiring notification and remedy of a defect if the Agency?s investigation shows a defect in design, construction, or performance of a motor vehicle that presents an unreasonable risk to safety. 49 U.S.C. ?? 30102(a)(9), 30118. Since the information before the Agency is not indicative of a vehicle-based defect, it is unlikely that any investigation opened because of granting this petition would result in an order concerning the notification and remedy of a safety-related defect. Therefore, upon full consideration of the information presented in the petition and the potential risks to safety, the petition is denied. The denial of this petition does not foreclose the Agency from taking further action if warranted or the potential for a future finding that a safety-related defect exists based upon additional information the agency may receive.A Federal Register notice further detailing NHTSA?s reasons for denial of the petition will be forthcoming.

The contact owns a 2012 Mercedes-Benz E550. The contact stated that while occupying the vehicle while the vehicle was parked, the ignition switch failed to detect the key fob. The vehicle was taken to an independent mechanic, where it was diagnosed that the electric steering rack had failed and needed to be replaced or reprogrammed. The vehicle was not repaired. The contact related the failure to an unknown recall. The manufacturer was notified of the vehicle, but no assistance was provided. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was 69,000.

NHTSA ID

11666601

Incident

May 27, 2025

Mileage

69,000 mi

The contact owned a 2012 Mercedes-Benz E550. The contact stated while her husband was driving 20-25 MPH and making a right turn, the brake pedal was depressed but traveled down to the floorboard, and the vehicle failed to respond. The contact's husband stood on the brake pedal; however, the vehicle failed to respond and crashed into a small ditch. The contact was occupying the front passenger's side seat at the time of the incident. The contact was unsure whether there was a warning light illuminated. The air bags deployed. The contact stated that there was smoke coming from the air bags. Both the contact and her husband immediately exited the vehicle. The contact's husband did not sustain any injuries. The contact stated that her left arm was deformed. The contact was transported to the Hospital by a family member. The Doctor diagnosed that the contact had sustained two broken bones on the left arm and two broken bones on the left foot. The contact underwent surgery and was scheduled for physical therapy. The contact was unsure whether a police report was filed. The vehicle was towed and totaled by the insurance company. The dealer was not notified of the failure. The manufacturer was notified of the failure and advised the contact that a field inspector would be sent to inspect the vehicle. The failure mileage was unknown.

NHTSA ID

11629095

Incident

Oct 13, 2024

The Electronic Steering Lock (ESL) will fail and cause the vehicle to become disabled. The failure of this part will leave the owner strained and unable to use any functions of the car. You can’t even put the vehicle into neutral to move the vehicle. Everything is locked. There have been numerous reports of this failure on various Mercedes Benz forums on the web. Also, many videos outlining this problem on YouTube. Yes, the problem has been reproduced by an independent repair facility. Mercedes Benz is aware of this problem regarding the ESL part. I believe they even published a TSB regarding the failure of this part. The car did not display any warning lamps or messages. The car is just dead! It’s very scary getting into your car and it doesn’t start when you turn the key. All other systems checked out on the car i.e. battery, voltage, fuses, sensors etc. Once that ESL stops working your car becomes a static display.

NHTSA ID

11570918

Incident

Feb 8, 2024

The contact owns a 2012 Mercedes-Benz E550. The contact stated while driving 55 MPH, there was an abnormal fuel odor inside the vehicle. There was no warning light illuminated. The vehicle was taken to the dealer and the contact was informed that the fuel sender unit was cracked, and that fuel was leaking into the rear seats of the vehicle. The contact was informed that the fuel sender unit needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and stated that the VIN was not under recall. The failure mileage was 80,000.

NHTSA ID

11541184

Incident

Aug 21, 2023

Mileage

80,000 mi

My car will not start and I get a message stating "Remove key from ignition" every time I insert the key to try to start the car. It appears that the ESL has failed. I have visited several MB forums and it appears that this is a common issue, regardless of car mileage. This is a factory defect that really needs to be recalled and fixed.

NHTSA ID

11521883

Incident

Feb 21, 2023

I WAS BACKING THE CAR WHEN THE STEERING BECAME STIFF AND A MESSAGE STATING 'POWER STEERING MALFUNCTION SEE OWNERS MANUAL' APPEARED. I TURNED THE CAR OFF AND RESTARTED AN HOUR LATER AND THE SAME MESSAGE APPEARED. STEERING WAS VERY DIFFICULT. THANKFULLY, IT DIDN'T HAPPEN AT A HIGH SPEED OR TURNING.

NHTSA ID

11348881

Incident

Jul 13, 2020

Mileage

113,000 mi

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES-BENZ E550. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS) HOWEVER, THE PART NEEDED FOR THE REPAIR WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. MERCEDES-BENZ OF ALEXANDRIA (200 S PICKETT ST, ALEXANDRIA, VA 22304) WAS CONTACTED AND IT WAS CONFIRMED THAT THE REMEDY PART WAS NOT AVAILABLE. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE. ## VIN PASSED ## MERCEDES-BENZ E550A 2012 ##*DT*JB

NHTSA ID

11337946

Incident

Jan 18, 2019

TL* TAKATA RECALL. THE CONTACT OWNS A 2012 MERCEDES-BENZ E550. THE CONTACT RECEIVED A RECALL NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS). THE PART NEEDED FOR THE REPAIR WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT CALLED MERCEDES-BENZ OF UNION RAY CATENA (2585 US-22, UNION NY 07083, (908) 356-6805) AND WAS INFORMED THAT THEY WOULD NOT TOUCH THE VEHICLE UNTIL THE MANUFACTURER PROVIDED THE PART FOR THE REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND INFORMED THE CONTACT THAT THE PART WOULD BE AVAILABLE IN MAY OF 2020. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

NHTSA ID

11242300

Incident

Jun 18, 2019

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Potential corrosion on the rear axle carrier Cause Due to market-specific conditions such as moisture, ingress of dirt and/or environmental influences, corrosion can occur on the rear axle carrier Remedy In the event of a complaint, the optimized repair method must be used when replacing the rear axle carrier. The repair method for the respective model series can be found in the attachment. Repair packages are available in Xentry Repair Packages for the special processing of rear axle carriers Note: Please utilize flexible wand (319-SAT1058826) along with the Cavity Preservation Gun (W 000 588 03 72 00) for cavity wax application to improve coverage and reduces labor efforts. The flexible wand may be obtained through the Mercedes-Benz Standard Service Equipment Program website.

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304