2015 Mercedes-Benz E550

On April 10, 2020, NHTSA's Office of Defects Investigation (ODI) received a defect petition from Mr. Surjit Singh alleging premature corrosion of the rear brake lines in his 2013 Mercedes-Benz E350 sedan. The petitioner states that he was recently informed by a Mercedes dealer service department that his car had severely rusted brake lines that need[ed] to be replaced immediately at a cost of about $3300. He further stated that the dealer service advisor informed him that he had seen the issue on many cars like his. The petitioner requested ?that NHTSA launch an investigation into this serious issue of rusting brake lines on [his] 2013 Mercedes E350.? The brake line corrosion reported by the petitioner did not result in brake line leakage or any compromise in brake system performance before it was detected in a dealer vehicle inspection. The petitioner submitted a complaint to NHTSA documenting his experience (NHTSA ID 11319024).On April 24, 2020, ODI opened Defect Petition DP20-004 to evaluate the petitioner?s request. ODI conducted a search for all consumer complaints and Early Warning Reporting (EWR) data related to allegations of brake line corrosion or leakage in 2013 Mercedes-Benz E350 sedans and similarly equipped vehicles. The 2013 E350 is a fourth-generation Mercedes-Benz E-Class vehicle (W212 platform), which was first sold in the United States in 2009 as a 2010 model. Mercedes-Benz sold approximately 245 thousand model year 2010 through 2015 E-Class sedan and wagon vehicles in the United States with the same brake line design as the petitioner?s vehicle.ODI?s search for complaints and EWR data in 2013 Mercedes E350 vehicles found no additional records related to the alleged defect. Expanding the search to all W212 platform vehicles identified just one incident, a complaint alleging unspecified brake line corrosion and leakage in a 2011 Mercedes-Benz E550 (NHTSA ID 10902081). The complaint did not allege that the brake line leakage resulted in reduced brake performance, crash, or injury. The resulting failure rate of 0.4 failures per hundred thousand vehicles is extremely low for a population that includes vehicles that have been in service for over ten years. After reviewing the available data, ODI has not identified evidence of a defect trend in the subject E-Class vehicles that would support opening a defect investigation into premature brake line corrosion failure. NHTSA is authorized to issue an order requiring notification and remedy of a defect if the Agency?s investigation shows a defect in design, construction, or performance of a motor vehicle that presents an unreasonable risk to safety. 49 U.S.C. ?? 30102(a)(9), 30118. Since the information before the Agency is not indicative of a vehicle-based defect, it is unlikely that any investigation opened because of granting this petition would result in an order concerning the notification and remedy of a safety-related defect. Therefore, upon full consideration of the information presented in the petition and the potential risks to safety, the petition is denied. The denial of this petition does not foreclose the Agency from taking further action if warranted or the potential for a future finding that a safety-related defect exists based upon additional information the agency may receive.A Federal Register notice further detailing NHTSA?s reasons for denial of the petition will be forthcoming.

TL* TAKATA RECALL. THE CONTACT OWNS A 2015 MERCEDES-BENZ E550. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V010000 (AIR BAGS) HOWEVER, THE PART TO DO THE RECALL REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE DEALER, MERCEDES-BENZ OF CHANDLER 7450 W ORCHID LN, CHANDLER, AZ 85226 WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

NHTSA ID

11316553

Incident

Mar 15, 2019

COLLISION HAZARD WARNING. NEITHER THE VISUAL WARNING ON THE DASH OR THE AUDIO WARNING WORKS PROPERLY. THE VISUAL AND AUDIO WARNING WILL ACTIVATE WHEN THERE ARE NO CARS ANYWHERE IN THE VICINITY. BUT IF A CARS SLOWS OR STOPS SUDDENLY IN FRONT, THERE WILL BE NO VISUAL OR AUDIO WARNING.

NHTSA ID

10872524

Incident

May 11, 2016

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint When closing the door, the side window may remain slightly open (short stroke position). Automatic window raising function of side window inoperative. NOTE: Window is fully operational while holding the switch Cause Software in door control unit (N69/x). Starting the engine at the same time as the door is closing (short stroke closure of window lifter) may result in a denormalization of the window lifter system. Remedy Update the software in the affected door control unit (N69/x). • This requires the door control unit (N69/x) to be commissioned. • (Path: XENTRY Scope; Control units view; DCU-XX (N69/x); Adaptations; Commissioning) Availability of the repair software in the field organization: • Since 10.10.2020 for model series 238, 257, 217 (FACELIFT) and A/C205 (FACELIFT) • Since 12.04.2021 for model series 118