2023 Mercedes-Benz EQE 350+

As i was driving on the interstate, i heard a gunshot-like explosion and the sunroof glass broke. Glass shards fell into the car. I had to slow down to 30 mph and exit the interstate. There was no obvious road debris or cars around me at the time of the incident. I drove the car to the dealership where it is for repair

NHTSA ID

11749068

Incident

Jun 18, 2026

LEMON LAW NOTICE: [XXX]– [2023 CPO Mercedes EQE350+] – Repeated Defects- Vehicle Safety feautures non functional I request that the TxDMV Enforcement Division investigate the deceptive trade and inspection practices of Mercedes-Benz of North Houston, and compel the dealership to cover the full physical repair and component costs required to bring this vehicle back into manufacturer safety compliance at my local servicing facility. I hold formal video diagnostic evidence provided by a certified technician confirming these facts and will provide it immediately upon request by an investigator. To: AutoNation Corporate Customer Care / Executive Escalations From: [XXX] Date: June 20, 2026 Subject: Escalation: Misrepresentation and Mandatory CPO Inspection Failure – Mercedes-Benz of North Houston Vehicle & Purchase Details: Vehicle: 2023 Mercedes-Benz EQE 350+ VIN: [XXX] Purchase Date: [XXX] Selling Dealership: Mercedes-Benz of North Houston (An AutoNation Dealership) Servicing Dealership: Mercedes-Benz of West Houston Statement of Issue I am writing to formally escalate a serious matter regarding a breach of the Mercedes-Benz Certified Pre-Owned (CPO) standards and a misrepresentation of vehicle condition by Mercedes-Benz of North Houston. I am seeking corporate intervention to resolve a high-cost repair stemming entirely from an undisclosed, out-of-specification pre-existing condition present at the time of sale. Chronology of Events [XXX] (Purchase & Test Drive): I purchased the vehicle as a Certified Pre-Owned unit from Mercedes-Benz of North Houston. During the initial test drive, I explicitly noted and pointed out an active issue with the radar/sensor system to the sales team. Delayed Delivery: Due to this sensor issue, the dealership delayed delivery of the vehicle for approximately 2 to 3 weeks to allegedly resolve the problem. I took delivery in December 2025 once the sensors appeared to be functi INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11745521

Incident

Jun 15, 2026

The vehicle has had repeated failures related to the air conditioning system and abnormal battery drain when the heating system is used. The vehicle has been taken to the dealership four times for the same issue and has spent more than two months in total at the dealership for repairs. The technicians have indicated that they have not been able to properly repair the problem. The vehicle continues to have unresolved defects affecting its normal operation and reliability. The vehicle has been at the dealer again from 3/26/2026 to present.

NHTSA ID

11729782

Incident

Oct 3, 2025

Description of Incident: On January 19, 2026, this vehicle was involved in a severe frontal collision. Despite significant structural damage resulting in a total loss (GEICO Claim: 0445628610101151), multiple critical safety systems failed to activate. Specific System Failures: SRS (Airbags): None of the 10 airbags deployed despite a high-energy impact that met deployment thresholds. Active Brake Assist: The system failed to monitor traffic or apply autonomous braking to reduce impact severity. Steering/Stability Assist: No steering intervention or collision warnings were provided during the pre-crash phase. GUARD 360: Collision detection monitoring failed to log the event. Safety Risk: The failure of the airbags to deploy during a high-energy impact represents a catastrophic failure of safety systems mandated by FMVSS 208 and directly increased the risk of occupant injury. Warning Symptoms: The dashboard was clear of all safety faults. No SRS or restraint system warning lights were present prior to the incident. Inspection Status: As of January 22, 2026, the vehicle is being held at Mercedes-Benz of Stevens Creek (San Jose, CA). It is awaiting a formal technical inspection from Mercedes-Benz Corporate. The vehicle is available for NHTSA inspection.

NHTSA ID

11713424

Incident

Jan 19, 2026

My Mercedes-Benz EQE has an intermittent but dangerous brake failure. When braking lightly and then needing to brake harder, the brake pedal becomes soft and fades, sinking further with almost no increase in braking power. The vehicle continues moving forward even when pressing the pedal harder. I must quickly release the pedal and press it again to regain braking. This creates a serious risk of crashing, especially at low speeds or in traffic. The issue is happening more frequently. Mercedes-Benz of Encino told me “everything is good,” but the issue continues. Another dealership (Mercedes Keys European) refused to even inspect the vehicle. A loaner EQE I drove for several days did NOT have this issue, confirming my vehicle’s braking system is not normal. This is a major safety defect, and I am requesting NHTSA to investigate.

NHTSA ID

11701695

Incident

Jul 1, 2024

September 8th, 2024 @ approximately 3pm My Mercedes EQE 350+ accelerated to a high speed when the front tire touched a curb. The car ran over the curb and into the parking lot. I was able to steer the car but the brakes didn't work. The car kept going through a stop sign and into the intersection. Luckily there were no cars in the intersection and I finally thought to turn the car off. It then stopped. The whole rubber covering over the battery was destroyed from the rocks on the curb. The battery was severely damaged also. The car was at the dealership from Friday Sept 13th until around Oct 9th. They finished their testing and sent the info to corporate Mercedes on Wed Sept. 18th. I finally heard back from Mercedes corporate on Oct 3rd, 2024. They said that they didn't find any malfunctions. During this waiting period I was pressured by the Mercedes dealership to file an Insurance Claim. I said I wasn't filing a claim until I heard back from Mercedes Corporate. There have been several cases online where the same issue has occurred by other Mercedes owners. One was almost exactly the same as mine. The only difference was that the car stopped when the tires were flattened. I have been driving for 50 years and have never experienced anything like this. My nephew was in the car with me and I repeatedly said to him the brakes aren't working. The car was a write off. I had to file an insurance claim.

NHTSA ID

11619675

Incident

Sep 8, 2024

On [XXX] an alert pop up on dash board saying to stop the car. I was driving I [XXX]. When stopped car showed an alert to Tow the car to dealer because a malfunction in the system. Called tow company and went to the dealer. They told me that day that the magnet part that regenerates when brake was broken. After 15 days I called back for an updated then they told me a software update is necessary and will be released on May 2024. On [XXX] dealership contacted me and gave me my car back with no repair or software update installed. There are reports that this car model stops when an error occurs, if they don't fix the software could be an accident. Being software means that could affect at least all the car in this model EQE 350 SUV, or even all the EV form this manufacturer INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11590871

Incident

Mar 12, 2024

Driving almost 60 mph, car shuddered and went to 20 mph then 10 mph in seconds. Drove on the shoulder, only 650 miles since I leased the car. Second time has happened in four weeks.

NHTSA ID

11579179

Incident

Mar 22, 2024

A software update is available to enable Plug & Charge at Tesla Superchargers. Schedule a workshop visit with your dealer to receive the update.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: • The vehicle must be exhibiting the concern as shown in the attachment videos. • The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. • If the geographic location is known, it is very important that it is provided. • Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.

Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.