2014 Mercedes-Benz GL550

Vehicle was parked on the driveway, brake sign came on upon start and system malfunction error showed on screen, vehicle started lowering automatically and Air compressor stopped working.

NHTSA ID

11756541

Incident

Aug 3, 2026

I recently purchased my Mercedes from Auto Boutique in Pearland, Texas (713) 352-0777. 1.The vehicle's air suspension system is constantly grinding, and moving/adjusting while being driven. It feels like the vehicles fame is off balance. 2. The back camera system does not work unless the radio is turned on; which is very alarming not to mention dangerous. 3. All the tires are registering improper inflation errors even though no air has been added or removed. I took the vehicle back to the place of origin; but they are not Mercedes Certified to address the issues. I am terrified to drive the vehicle, and it stays parked in the garage

NHTSA ID

11672674

Incident

Jun 14, 2025

The contact owns a 2014 Mercedes-Benz GL550. The contact stated that the check engine warning light was illuminated. The vehicle was taken to the dealer, where it was diagnosed with leaky exhaust valves. The dealer determined that the exhaust valves needed to be replaced. The vehicle was taken to an independent mechanic, where a similar assessment was made. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the vehicle was not covered under TSB Number: 10233794. The manufacturer referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 104,000.

NHTSA ID

11611751

Incident

Aug 7, 2024

Mileage

104,000 mi

Leaky exhaust valves

NHTSA ID

11610291

Incident

Jul 17, 2024

The contact owns a 2014 Mercedes-Benz GL550. The contact stated while driving at an undisclosed speed, the steering wheel seized, and the vehicle lost motive power. The check engine and malfunction PP0 warning lights illuminated. The contact was able to steer the vehicle to the shoulder of the roadway. The contact stated that an independent mechanic facility was nearby, so the mechanic and the contact pushed the vehicle into the shop. The vehicle was diagnosed with failed cam shaft gear and lifters. The contact was informed that the cam shaft gear and lifters needed to be replaced. The vehicle was not repaired. The contact stated that the vehicle had been taken to the dealer previously because of an abnormal sound however, the mechanic was unable to duplicate the failure. The manufacturer was not made aware of the failure. The failure mileage was approximately 100,000.

NHTSA ID

11569931

Incident

Sep 19, 2022

Mileage

100,000 mi

Tapping noise developed in the engine, after dealership inspection using borescope, scored cylinder walls were found, resulting to engine replacement. Please see: Lena Jamil, et al. v. Mercedes-Benz USA, LLC (Case No: 2:22-cv-08130-FLA-AFM)

NHTSA ID

11537166

Incident

May 24, 2023

I HAD JUST ARRIVED HOME. THE CAR WAS OFF AND I WAS PARKED IN MY GARAGE. I OPENED THE DOOR BUT IT DIDN'T OPEN ALL THE WAY TO THE FIRST HINGE. MY HAND WAS IN THE DOOR AS IT SLOWLY STARTED TO CLOSE. THE DOOR CAUGHT SLIGHTLY AND THE SOFT CLOSE FEATURE ACTIVATED. MY THUMB WAS CAUGHT IN THE DOOR AND WAS CRUSHED AS THE DOOR SEALED COMPLETELY CLOSED WITH THE SOFT CLOSE FEATURE. I WAS UNABLE TO OPEN THE DOOR DURING THIS TIME. I WAS YANKING ON THE DOOR HANDLE TRYING TO OPEN THE DOOR TO FREE MY THUMB BUT THE DOOR WOULD NOT OPEN UNTIL THE SOFT CLOSE WAS COMPLETE. AS A RESULT MY THUMB WAS CRUSHED. I BELIEVE THAT THIS A DESIGN FAULT WITH THE VEHICLE. THE FACT THAT THERE WAS NO SENSOR TO DETECT SOMETHING IN THE DOOR AS WELL AS NOT BEING ABLE TO OPEN THE DOOR AT ANY POINT DURING THE SELF CLOSE PROCESS PRESENTS MANY SAFETY ISSUES! I REACHED OUT TO MERCEDES DIRECTLY AND THEY SAID AFTER AN EVALUATION THAT THE VEHICLE WORKS THE WAY IT'S DESIGNED AND THAT THE DOOR COULD OPEN DURING ANYTIME OF THE SOFT CLOSE FEATURE. I MADE A SHORT VIDEO SHOWING THAT IN FACT YOU CAN NOT OPEN THE DOOR DURING THE SOFT CLOSE PROCESS. MY FINGER WAS NOT BROKEN BECAUSE I CLOSED THE DOOR ON IT! THE DOOR WASN'T CLOSED ALL THE WAY, IT HAD ONLY JUST SLIGHTLY LATCHED AND WAS THEN CRUSHED BY THE SOFT CLOSE. I EXPLAINED TO MERCEDES THAT THIS WAS VERY DANGEROUS ESPECIALLY WITH MY 3 AND 5 YEAR OLD. IF IT CRUSHED MY THUMB IT WOULD BREAK THEIR HAND!! AFTER I DISPUTED THAT YOU CAN'T OPEN THE DOOR SOMEBODY HIGHER UP AT MERCEDES CALLED ME AND SAID THAT I WAS CORRECT YOU CAN'T OPEN THE DOOR DURING THE SOFT CLOSE AND THAT I WAS RIGHT BUT THAT IS THE WAY THE VEHICLE IS DESIGNED THEREFORE IT'S OPERATING CORRECTLY. WHEN I ASKED WHAT THEY WOULD DO HE SIMPLY ASKED WHY DON'T I JUST GO AND BUY A NEW CAR WITHOUT THE FEATURE!! I EXPLAINED THAT I DIDN'T FELL LIKE SPENDING ANOTHER $100 000.00 WHEN MY CAR IS ONLY 4 YEARS OLD!

NHTSA ID

11160890

Incident

Sep 18, 2018

Mileage

33,000 mi

DAIMLER AG, (DAG) THE MANUFACTURER OF MERCEDES-BENZ VEHICLES, HAS DETERMINED THAT ON CERTAIN GLE, GLS AND GLE COUP VEHICLES (166, 292 PLATFORM) WITH THE ACTIVE CURVE SYSTEM (ACS), THE OIL IN THE ACS'S OIL RESERVOIR COULD START FOAMING UNDER DYNAMIC DRIVING SITUATIONS IN COMBINATION WITH AN OIL LEVEL BELOW MINIMUM. THE OIL FOAM MIGHT LEAK OUT OF THE OIL RESERVOIR THROUGH THE VENT HOLES IN THE SEALING CAP. DEPENDING ON THE ORIENTATION OF THE VENT HOLES IN THE SEALING CAP, LEAKING OIL COULD SPRAY ONTO HOT SURFACE COMPONENTS OF THE EXHAUST SYSTEM. IN SUCH A CASE THE RISK OF A FIRE CANNOT BE RULED OUT. AS A PRECAUTIONARY MEASURE AN AUTHORIZED MERCEDES-BENZ DEALERSHIP, WILL CORRECT THE OIL LEVEL IF NECESSARY AND REPLACE THE SEALING CAP OF THE OIL RESERVOIR WITH AN OPTIMIZED SEALING CAP TO PREVENT OIL FOAM LEAKAGE. SAFETY RISK: DEPENDING ON THE ORIENTATION OF THE VENT HOLES IN THE SEALING CAP, LEAKING OIL COULD SPRAY ONTO HOT SURFACE COMPONENTS OF THE EXHAUST SYSTEM. IN SUCH A CASE THE RISK OF A FIRE CANNOT BE RULED OUT.

NHTSA ID

11104245

Incident

Jun 27, 2018

Mileage

34,000 mi

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.