2020 Mercedes-Benz GLA 250

On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183

A bicyclist claims I almost ran him over. I didn’t hit him, but he fell over and made sued my insurance company. He claims he was at the right side of my car as I was merging towards the right to make a turn. If he was indeed in my blind spot, then it’s important to note that the blind spot assist didn’t alarm and that the design of the passenger seat does create a blind spot, especially for someone of short stature since I cannot see over the passenger seat. To avoid anything like this, I’ve had to remove the passenger headrest, it even at the lowest to the ground setting, the top of the passenger seat is higher than the rear passenger window, but at least the headrest no longer obstructs the view over my shoulder

NHTSA ID

11757199

Incident

Jun 24, 2024

Had just gotten on the expressway, when a loud gunshot noise was heard. Out of fear, I ducked down, thinking it had actually been one. However, I heard a lot of wind coming in as if a window was down, when I look up, majority of my panoramic sunroof was gone. No messages or warnings appeared on the dash, and I pulled over to document photos and videos. The shade below the sunroof was not damaged, seems to be an internal force that made it explode and shatter into a thousand pieces.

NHTSA ID

11682723

Incident

Aug 23, 2025

Problem has been confirmed by dealer that the rear differential assembly needs to be replaced. This is a very common defect with gla250’s. It been recalled in the past and Mercedes Benz is putting many drivers at risk. The estimated to replace is $6100! Mercedes Benz corporation refuses to replace the part only offering $1300. That is submission that they are aware something is wrong. I don’t feel safe driving a 2020 car. There have been many class action suits but there needs to be another investigation and recall which MB knows there is a problem and hazard

NHTSA ID

11664899

Incident

Jun 4, 2025

The contact owns a 2020 Mercedes-Benz GLA250. The contact stated that while driving 35-40 MPH, the check engine warning light illuminated. There was an abnormally loud rumbling sound heard. The contact pulled over and restarted the vehicle. The vehicle was taken to the local dealer, where it was diagnosed that the fuel injectors needed to be replaced. The vehicle was not repaired. The contact stated that the failure was related to TSB No: 2022030003. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was approximately 86,000.

NHTSA ID

11620953

Incident

Oct 17, 2024

Mileage

86,000 mi

My Mercedes Benz GLA250 has a faulty rear differential and began shuddering and driving poorly when it had 44K miles on it. This is a very premature failure as diagnosed by two repair shops and is happening to thousands of this model Mercedes Benz. The damage can be catastrophic if continued to be driven as the differential metal continues to deteriorate and possibly have metal shavings travel into the engine. I was told initially by Mercedes Benz it was bad tires! I replaced the tires and the shuddering became worse. I searched for the problem myself on the internet as the problem continued to worsen and countless people are complaining, saying it’s the rear differential. The cost is between $4K and $5K to replace.

NHTSA ID

11618120

Incident

Mar 1, 2024

Strong “gas odor” upon entering car And continues despite opening all windows to ventilate-also on one time occasion - sudden deceleration And “surging speed” alternately While cruising- it feels that the car Will “stop” and it’s worrisome that I may be “hit “ by the vehicle behind me- also several “dashboard warning lights” different messages just “flashed” which also caused some “Panic” on me- brought the car to the shop- all they did ABS sensor replaced- no other issues noted- I read from MB owners forums about MB Recalls about same issues NHTSA 21V-961 NHTSA 23V- 445

NHTSA ID

11616169

Incident

Sep 12, 2024

1. POWER STEERING: STEERING WHEEL WENT OUT ON A FREEWAY ALMOST CAUSING MASSIVE COLLISION (this has happened twice) 2. Car Jerkiness: reported this to MBZ of San Rafael for 2 years (went into shop 10+ times for same issue and not resolved. It lunges forward while driving. This also is a safety issue almost causing me to hit a pedestrian 3. Vehicle Not opening 4. Vehicle Overheating 5. Faulty Wiring 6. Screen Black out

NHTSA ID

11575791

Incident

Jan 1, 2024

Transmission problem. On several occasions while driving, the car has lurched to a stop because gear changed suddenly from Drive to Park. At other times, the engine revvs and slows when it suddenly switches from Drive to "M1." After stopping, it goes back to "D" on its own. Serious safety issue, as I can get rear ended in traffic, or cause an accident for stopping without notice. I have one photo of the sudden transmission switch to M1 (today). Car has been towed to Mercedes service department; no other inspection yet. No warning lamps. Only that it is happening more frequently.

NHTSA ID

11488566

Incident

Oct 9, 2022

Complaint Intermittent shift feel or thud/clunk noise perceived, such as a brief jerk or transmission reaction during certain driving situations. May be most noticeable when transitioning from a coasting condition to accelerator pedal application. May occur in all drive modes. Cause Dual‑clutch transmissions (DCT) inherently exhibit more dynamic shifting behavior compared to other types of transmissions. This is due to the use of physical clutches for starting and gear changes. In certain situations, dynamic driving behavior can lead to a slight jerk sensation which is a normal technical characteristic of the transmission. A typical example is a "Change of Mind" situation: • The customer is coasting towards a red traffic light. • The traffic light turns green while the vehicle is still coasting. • The customer then presses the accelerator pedal. In these situations, a slight jerk may occur briefly because the transmission must quickly engage the appropriate gear and control the clutches accordingly. Since shift forks are responsible for engaging the gears during shifting, a slight shifting noise may also be noticeable. Please note driving programs S, S+, and M are designed to provide sportier vehicle behavior and are not optimized primarily for maximum comfort, so this operation may be more audible. Remedy Verify the customer's concern and confirm proper transmission operation. If no faults or abnormal operating conditions are identified by IPR (Intelligent Predictive Repair), no hardware replacement is necessary. Inform the customer that the transmission has been designed to provide direct gear engagement and responsive vehicle performance. Under certain operating conditions, brief shift sensations may be perceptible and are consistent with the operating characteristics of the dual‑clutch transmission

Dear Mercedes-Benz Owner: In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage Detection ("DMTL") on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership. Why the Warranty extension? On certain Model Year 2018 - 2024 A / C / CLA / CLS / E / G / GLA / GLB / GLC / GLE / GLS / GT / S / SL Mercedes-Benz vehicles, under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code ("DTC") entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp ("MIL"). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. • If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. • This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Hand detection system – malfunction / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" "Active steering assist not available" Cause Possible causes: Hand detection mat, hand detection control unit, contacts, and electrical feed line. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Check: Please do not replace the HOSWD control unit. Please flash the new SW and perform the SCN coding for the HOSWD control unit (N179/1) (available from July 2026). The software can be flashed onto all HOSWD213 with HW number A0009011522 and all HOSWD223 with HW number A0009011422. Please also flash the SW for the IDC control unit (N62/4), if possible (only applies to HOSWD223). Erase fault memory Remedy: Turn on the ignition or start the engine without touching the steering wheel. If, after 10 seconds without touching the steering wheel, one of the three fault messages appears on the instrument cluster: Check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, crimp connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage -> replace the steering wheel rim. If a yellow message does not appear on the instrument cluster within 10 seconds: Grasp the steering wheel fully with both hands, including the chrome molding at the 6 o'clock position (see picture 1). If the fault is triggered by grasping the steering wheel rim or pressing the clip at the 6 o'clock position, check the contacts and feed lines in the steering wheel by means of a visual inspection for damage, kinked connections, loose connections, etc. (example in picture 2 and 3). Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). If there is visible damage -> replace the steering wheel electronics or the feed lines. If there is not any visible damage: Replace the steering wheel rim. Please do not replace the HOSWD control unit. A TIPS case should be created if fault profile is unclear. In the event of a customer complaint and a further fault code in HOSWD: B1E7713: Check the ground connections (screw connections and cables to the steering wheel rim); if necessary, retighten the screws/bolts and check for corrosion (picture 4). B1F1F04: Check the control unit of the hand detection system; if necessary, replace this with the control unit from a donor vehicle (make sure that the hardware part numbers are identical).

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).