2017 Mercedes-Benz GLS450

On 8/20/2026 I had a vacuum leak from the intake manifold and crankcase hoses repaired at a Vic's Bimmer Shop in the city of Lancaster California. This included the replacement of the oil separator breather on the engine. I drove my Mercedes Benz 2017 GLS450 less than 100 miles and the engine lost power and suddenly turned off. I was able to pull off onto the side of the freeway and then I saw smoke coming from under the hood and my wife and I exited the vehicle, called the fire department and the car burned completed on the side of the freeway and is a total loss. I believe the oil separator leaked oil onto the exhaust pipe and engine turbo which then started the fire.

NHTSA ID

11760731

Incident

Aug 28, 2026

Car did not brake when going about 5-7mph and crashed into another car.

NHTSA ID

11713114

Incident

Dec 19, 2025

The contact owns a 2017 Mercedes-Benz GLS450. The contact heard an abnormal humming sound when the vehicle was started, and the humming sound grew louder over time. The contact believed that the humming sound was coming from the driver's side headlamp. The contact stated that the headlamp was equipped with a small internal fan to dissipate heat. Additionally, other electrical failures were occurring, and the vehicle was taken to a local dealer. The dealer diagnosed the vehicle and determined that the blower motor had failed and needed to be replaced. The vehicle was repaired; however, the humming sound returned. The vehicle was taken to the dealer on two more occasions, and the dealer replaced the timing belt and the alternator, however the failure reoccurred. Recently, while touching the door handle, the contact heard a humming sound that was very loud. The vehicle was taken back to the dealer, and it was determined that the driver's side headlamp assembly needed to be replaced. The vehicle was not repaired. The contact researched online and related the failure to NHTSA Campaign Number: 20V626000 (Electrical System, Steering, Exterior Lighting, Visibility); however, the VIN was not included. The manufacturer was contacted and confirmed that the VIN was not included in the recall. The failure mileage was 135,500.

NHTSA ID

11710906

Incident

Aug 14, 2025

Mileage

135,500 mi

My 2017 Mercedes-Benz GLS 450 is experiencing serious and unpredictable transmission behavior related to the valve body and shifting mechanism. The transmission sometimes fails to engage Park, shifts on its own without driver input or attempts to engage Reverse unexpectedly. On multiple occasions the vehicle has moved or rolled after being placed in Park and once it appeared to shift itself toward Reverse. This behavior is a clear safety risk as the vehicle can suddenly lose control or move unexpectedly. It happens intermittently, without any dashboard warnings and often resets temporarily after restarting the car. According to multiple owners posting on Mercedes-Benz forums (including MBWorld, BenzWorld, and Mercedes-Benz Owners Club discussions), this issue is common among GLS and other Mercedes models using the same transmission. Many owners report identical symptoms: transmission slipping into Neutral or Reverse, failure to engage Park or erratic shifting caused by a malfunctioning valve body, defective solenoids or Transmission Control Module (TCM) faults. Some have shared diagnostic codes such as P073E and P07B7 that point to reverse and park circuit errors. Mercedes technicians and independent repair specialists who have posted on these forums frequently identify the valve body assembly as the source of the issue. Common explanations include internal hydraulic pressure faults, electrical connector leaks or sensor failures inside the valve body. Owners have been quoted thousands of dollars for valve body replacements as i was billed $2300+. This problem is not isolated to my vehicle and appears to be a recurring design or manufacturing defect that affects multiple model years and platforms sharing this transmission. Because the vehicle can unexpectedly shift or fail to hold Park, it creates an immediate safety concern for both drivers and bystanders. I have video of this dangerous issue

NHTSA ID

11695525

Incident

Feb 15, 2025

On July 23, 2025, I drove my Mercedes-Benz GLS 450 to a medical appointment. After arriving, I parked near the valet station, turned off the car, and went inside to check in at LabCorp. Within two minutes, witnesses reported black smoke from the hood — followed by a violent explosion that shook the office building and triggered a multi-unit response from local fire and police departments. When I came downstairs, my vehicle was engulfed in flames. The front end was completely destroyed. Mercedes-Benz USA sent an investigator on September 8, 2025 to examine the wreck. Despite numerous follow-ups, I have received no written report, no findings, and no communication from Mercedes-Benz since that inspection detailing any relevant information. Safety Context: In March 2024, Mercedes-Benz issued Recall #24V-207, affecting 2019–2023 GLE and GLS models, citing a defective 48-volt ground connection that could cause a fire. My incident occurred in a GLS 450 model and appears consistent with this recall defect. If confirmed, this could indicate that the recall did not capture all affected VINs or that repairs were not properly executed. This incident was minutes from being fatal — and could easily have occurred on the highway or in my garage or with my 4 children inside. The lack of corporate response for over two months raises serious concerns about consumer safety, recall effectiveness, and corporate transparency.

NHTSA ID

11693202

Incident

Jul 23, 2025

Vehicle Information: Make: Mercedes-Benz Model: GLS 450 Year: 2017 Component: Visibility/Sunroof/Panoramic Glass Roof VIN: [XXX] Incident Date: [XXX] Complaint Summary: I am filing this complaint regarding a serious and dangerous safety defect in my 2017 Mercedes-Benz GLS 450. Without warning and while driving, the panoramic glass sunroof suddenly shattered and exploded, sending glass shards and debris into the vehicle cabin. My two young children were seated inside at the time, and glass pieces fell directly onto them, causing extreme distress and posing a severe risk of injury. There was no impact or external cause—the sunroof shattered spontaneously. The incident left glass scattered throughout the interior of the vehicle, including on the seats, floor, and children’s car seats. Fortunately, my children were not severely injured, but the potential for serious harm was extremely high. After researching this issue, I discovered that this is not an isolated incident. Numerous complaints have been filed with the NHTSA and other authorities regarding spontaneous sunroof shattering in Mercedes-Benz vehicles, including this model. Additionally, I understand that a federal judge recently approved a class action lawsuit addressing this exact issue, further highlighting the severity and prevalence of the defect. This is a significant safety hazard that must be addressed. I urge the NHTSA to investigate this issue further and take appropriate regulatory or enforcement action to ensure the safety of all vehicle occupants. Additional Details: No recent repairs or modifications to the sunroof or roof area. Vehicle was in motion on a clear day with no overpasses or external objects that could have impacted the roof. The noise was loud, like an explosion, followed by immediate glass breakage. I have retained photos of the damage and can provide them if needed. Requested Action: Please investigate this matter urgently. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11666914

Incident

Jun 7, 2025

Vehicle check engine light came on early August 2024. Vehicle was brought in for service and checked for codes. B1F4500 Battery has excessive resistance B21059A The operating conditions of component have not been satisfied. Battery was replaced and rechecked. Po4427A Evap leak detected P04F000 Charcoal canister has a malfunction Smoke tested EVAP system to see if there was any leaks and tested the valves to make sure EVAP system was working correctly. Charcoal canister not actuating correctly so was replaced and checked. Gas cap also replaced Several days later Check engine light returns. Code continues to say "Small leak in the EVAP system." Every time the code is cleared it returns and Check Engine light returns. This has been going on for 7 months. Car cannot obtain the required SMOG inspection in California that is required for an annual registration of the vehicle. I believe the vehicle may need to be part of the Emission Service Campaign 2024030005 which has effected 16 other vehicles. Mercedes tells me that an update to the Engine Control Software will not be allowed because my vehicle is not one of the 16 vehicles that are currently effected by this issue. The issue is for the same make, model and year as my vehicle.

NHTSA ID

11646348

Incident

Aug 8, 2024

This is the 2nd time within a year my airmatic suspension system has went out while driving and I have lost control of driving my vehicle. I have paid 3900 to have the problem repaired it has not been a year and the same issue has happened. Faulty dangerous suspension system airbag suspension is dangerous and faulty.

NHTSA ID

11628461

Incident

Nov 29, 2024

Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic /9G‑TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G‑TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on‑going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: ‑ NAG3 Classic (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG sport model (AMG 43 and AMG 53 with converter, automatic transmission 725.0) ‑ NAG3 Classic ‑ Hybrid (automatic transmission 725.0) ‑ NAG3 Classic ‑ AMG 63 (automatic transmission 725.0) ‑ NAG3 MOPF ISG2 (automatic transmission 725.1) ‑ NAG3 MOPF Hybrid (automatic transmission 725.1) ‑ NAG3 MOPF AMG sport model (AMG 53/AMG 53e with ISG48V2 & converter /hybrid, automatic transmission 725.1) ‑ NAG3 MOPF AMG 43/63 with engine 139/177 (automatic transmission 725.1) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. ‑ Ask precise details about the customer complaint and the conditions and context. ‑ Fill out the service reception questionnaire (please see WIS document: OF27.00‑P‑3000‑05A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: 1. Perform quick test 2. Access the transmission control unit via XENTRY Diagnosis 3. Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). 4. The IPR repair instructions are displayed, Carry out the IPR repair instructions without performing any further diagnostic or repair steps. ‑ Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. Invoicing for the guided IPR steps: Operation item 27‑0640 and 0.1 hours Notice regarding warranty: The use of IPR in association with warranty claims is mandatory! If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. ·Tamper‑proof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner ‑ either in digital form or as a hard‑copy printout and also enclose a printout with the damaged part. In this regard, please comply with the country‑specific warranty requirements of the MPC/general distributor.

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Only vehicles with a variable transfer case are affected. This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 ‑ All‑wheel drive (ARS) N127 ‑ 'Drivetrain' (PTCU) control unit Y3/8 ‑ Transmission control for 9‑gear transmission (VGS) N3/10 ‑ Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications ‑ Collect an oil sample of the original fluid 5. Complete all transfer case Tech‑in processes located under VG Control Unit > Adaptations ‑ Resetting the oil service data ‑ Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature (>60C ) 6. Operate vehicle in full circle with steering at full lock ‑ 5x to the left ‑ 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If this LI has already been applied to the vehicle, please submit a TIPS case to the Powertrain inbox with the following information: ‑ Initial quick test with fault freeze frame data ‑ Initial transmission EEPROM data ‑ VGS and Transfer Case Control Unit Log (N45 or N15/7) ‑ Special Acquisition Data .txt file (Transfer Case Control Unit > Special Procedures > Procedures for support queries to market support > Special Data Acquisition) ‑ Photo of the original oil condition ‑ What color was the fluid drained from the transfer case before the oil change? ‑ Was an oil sample collected, and can you provide a photo of the original fluid? ‑ What color and part number fluid was used during the oil change? ‑ How far was the vehicle driven after?

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G‑TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G‑TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on‑going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 ‑ AMG sports models (AMG 43 and AMG 53 with converter) NAG3 ‑ AMG 63 NAG3 ‑ Hybrid NAG3 Facelift (automatic transmission 725.1) NAG3 facelift (725.1) with engine 139/177 (AMG 43/63) Steps for the Service Advisor: Important: The more information and detail that can be given to the workshop about the complaint, then the more effective the subsequent diagnosis with IPR can be. To this end, a detailed service reception questionnaire has been provided to help the Service Advisor ask the right questions about the complaint. ·Ask precise details about the customer complaint and the conditions and context. ·Fill out the service reception questionnaire (please see WIS document: OF27. 00‑P‑3000‑05A) for customer complaints in detail and forward it to the workshop. Operation steps for the workshop employee: Perform quick test ·Access the transmission control unit via XENTRY Diagnosis ·Select "A customer complaint has been received" and carry out all subsequent operation steps (IPR diagnosis path). ·The IPR repair instructions are displayed. Carry out the IPR repair instructions without performing any further diagnostic or repair steps. ·Important: The IPR repair instructions are binding and must be carried out. Differing repairs are possible; such repairs must be documented in XENTRY in free text. Please observe the information regarding the IPR diagnosis process in XENTRY. ·Conventional diagnosis and subsequent appropriate repairs are only permitted if IPR does not specify any repair instructions. ·Invoicing for the guided IPR steps: Operation item 27‑0640 and 0.1 hours !!!!! Notice regarding warranty: !!!!! ·The use of IPR in association with warranty claims is mandatory! ·If the IPR repair instructions are disregarded without justification, the warranty claims may be rejected and/or are subject to debit. IPR will provide a measure to repair the vehicle based on various data sources (EEPROM, fault codes, etc). Please consider the vehicle maintenance record of the vehicle. For warranty and goodwill repairs, the transmission ECU test log and/or IPR test result must be uploaded into Paperless XENTRY Diagnosis (pXD) . If repair is being determined based of oil pan condition pictures of oil pan MUST be provided to warranty as justification. ·Tamper‑proof documentation: The IPR repair instructions are stored in the control unit log. Please file this document in a tamperproof manner ‑ either in digital form or as a hard‑copy printout and also enclose a printout with the damaged part. In this regard, please comply with the country‑specific warranty requirements of the MPC/general distributor.

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!