2000 Mercedes-Benz SL500

THE SUBJECT S-CLASS VEHICLES CONTAIN A COMPRESSED AIR SUSPENSION SYSTEM THAT USES AIR STRUTS ON EACH OF THE FOUR WHEELS IN LIEU OF TRADITIONAL SPRINGS AND SHOCK ABSORBERS.THESE AIR STRUTS USE COMPRESSED AIR TO SUPPORT THE WEIGHT OF THE VEHICLE AND CONTROL RIDE HEIGHT.IN THE EVENT OF THE LOSS OF AIR FROM THE SYSTEM, AN ALERT WILL FLASH ON THE INSTRUMENT CLUSTER WARNING THE DRIVER TO EITHER DRIVE CAREFULLY OR TO STOP THE VEHICLE.THE VEHICLE RIDE HEIGHT CAN BE REDUCED BY AS MUCH AS 105 MM BELOW NORMAL RIDE HEIGHT BEFORE THE FULL LOAD OF THE VEHICLE FOR THAT WHEEL COMES TO REST ON A STEEL ROD, WITH A RUBBER STOP ON THE END, LOCATED IN THE SHOCK ABSORBER.THIS REST-STOP CONDITION IS DESIGNED SUCH THAT THERE IS NO IMPACT ON VEHICLE CONTROL.MERCEDES-BENZ (MBUSA) SUPPLIED VIDEO SHOWING A VEHICLE IN THIS CONDITION OPERATING UNDER SEVERAL DIFFERENT SITUATIONS INCLUDING EVASIVE MANEUVERS DEMONSTRATING THE ABILITY OF THE VEHICLE TO BE CONTROLLED EFFECTIVELY WITH A RIDE HEIGHT REDUCED TO THE MINIMUM.ONLY THOSE COMPLAINTS TO ODI AND MBUSA THAT ALLEGED A STEERING INTERFERENCE DURING A REDUCED RIDE HEIGHT CONDITION WERE COUNTED IN THIS RESUME FAILURE REPORT.SOME COMPLAINTS ALLEGED THAT WITH A REDUCED RIDE HEIGHT AND A STOP NOW WARNING MESSAGE THERE WAS A RUBBING NOISE WHEN TURNING, BUT THE ABILITY TO STEER THE VEHICLE WAS NOT COMPROMISED.A SAMPLING OF WARRANTY CLAIMS SUBMITTED BY MBUSA DID NOT REVEAL ANY INDICATING A LOSS OF CONTROL DUE TO AN AIRMATIC SYSTEM FAILURE.THERE WAS ONE CRASH REPORTED BY MBUSA TO ODI BUT THE INFORMATION AVAILABLE INDICATED THAT IT RELATED TO SUSPENSION SYSTEMS AND IT WAS NOT POSSIBLE TO VERIFY THAT THE INCIDENT WAS RELATED TO AN AIRMATIC SYSTEM FAILURE. FURTHER USE OF AGENCY RESOURCES IN THIS MATTER DOES NOT APPEAR TO BE WARRANTED.THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND WILL TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED.THIS PRELIMINARY EVALUATION IS CLOSED.

The contact owns a 1999 N/A Mercedes-Benz SL500. The contact purchased the rear brake rotors and pads from R1 Concepts, who sells auto parts on Amazon. When the contact installed the brake parts, the rotors could not be adjusted since the rotors were missing the opening that needed to be pre-drilled. The contact stated that when the rear brakes were adjusted, the defect was found. In addition, the contact stated that while parking the vehicle and setting the parking brake, there was an abnormal sound coming from the vehicle. The contact stated that the parking brake failed to engage. After several attempts, the parking brake was set. No warning lights were illuminated. A dealer was not contacted, and the vehicle was not diagnosed or repaired. The contact stated that the companies were selling defective products. The manufacturer was made aware of the failure but denied assistance. The failure mileage was unknown.

NHTSA ID

11691658

Incident

Sep 6, 2025

TL* THE CONTACT OWNS A 2000 MERCEDES BENZ SL500. WHILE DRIVING AT 40 MPH, THE INSTRUMENT CLUSTER EXPERIENCED AN ELECTRICAL MALFUNCTION. THE CONTACT INQUIRED WITH THE DEALER IN REGARDS TO NHTSA CAMPAIGN ID NUMBER: 06V028000 (INTERIOR LIGHTING) AND WAS ADVISED THAT HIS VIN WAS NOT INCLUDED WITH THE RECALL. THE CONTACT'S WARRANTY WAS EXPIRED AND ANY REPAIRS WOULD BE AT HIS EXPENSE. THE VEHICLE WAS NEITHER DIAGNOSED OR REPAIRED FOR THE FAILURE. THE FAILURE MILEAGE WAS 75,000 AND THE CURRENT MILEAGE WAS UNKNOWN.

NHTSA ID

10343213

Incident

Jul 11, 2010

Mileage

75,000 mi

Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.

Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. • If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: • LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304

Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).

Crease formation on genuine leather seat covers in vehicles with low mileage • Objects left on the seats for extended periods of time (pressure marks). • Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). • Light initial creases due to vehicle handling. • Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!