2009 Mercedes-Benz SL550

I'm reporting a SERIOUS SAFETY ISSUE affecting all Mercedes-Benz R230 series SL roadsters, model years 2003–2012, of which approximately 85,000 were sold in the United States: • There are numerous reports on R230 SL owners' online forums that an electrical device located in the trunk of these vehicles known as the BCM [Battery Control Module] is prone to CATASTROPHIC FAILURE and melt-down. • The failed BCM can subsequently CATCH FIRE – potentially destroying the vehicle and endangering lives and property nearby. See photos attached from one SL owner's experience. • MBUSA, its dealers, many SL owners, independent service centers and salvage yards are aware of this problem: multiple reports detailing it can easily be found on the Internet. Possible modifications to alleviate the danger have been affected by some SL owners, one picture of which has been uploaded here. • Mercedes-Benz is surely aware of the issue but has not recalled nor issued TSBs associated with this serious problem, nor has MBUSA acknowledged that vehicles modifications to alleviate the risk of failure and subsequent fires have been developed by owners and mechanics. • No symptoms are known to appear prior to melt-down, other than odors and/or smoke emanating from the SL's trunk. By then, it is TOO LATE. I respectfully request NHTSA open an investigation into this issue and require Mercedes-Benz address it by affecting modification or replacements of the faulty BCM system components in R230 vehicles.

NHTSA ID

11701077

Incident

Oct 13, 2023

Complete brake failure while driving. No one was injured but the vehicle could not be stopped until the transmission went into limp mode with still no brakes. Now the ABS and SRS lights on. Brake pedal to the floor. I completely have new brakes speed sensors fluid exchanges and more. The current recall doesn’t seem to cover my vehicle. I contacted the dealership and they said there are no open recalls.

NHTSA ID

11642407

Incident

Aug 21, 2024

This particular model 2009 Mercedes SL 550 hardtop convertible 5.5 liter motor has two batteries and accessory battery that battery that’s located in the trunk in the main starting battery that’s on the firewall. These batteries are both new in OEM recommended. If the car sits for 24 hours, it will not start. The electrical system is completely drained. There are many forms describing the same issue but yet the SL model is not included in a civil lawsuit. Mercedes-Benz definitely knows they have an issue in somehow it needs to be rectified.

NHTSA ID

11495761

Incident

Dec 1, 2022

[XXX] [XXX] [XXX] VIN # [XXX] SL550 2009 Since I bought this car 3 years ago the first day I am using it I got the problem say Reduced Braking Power, Depress Brake Pedal fully. I thought only when the weather is cold but now after 15 minutes minutes I am running on the road losing brake it is scary not only one time its always every 30 minutes now . I am stop using for a while . I try to bring in dealer for diagnose last 2 years ago they cant find the problem even my person mechanic. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).

NHTSA ID

11468670

Incident

Nov 15, 2019

I bought the almost 3 years now since I bought it I seen and message on the dash board Reduced Braking Power Depress Brake Pedal fully . I search on the website most the Mercedez Benz has same problem but when check my Vin number I saw no issue on my SL550 2009. I almost depress on my car ill spend a lot of money and its dangerous to used it I went to a dealer 2 years ago for but on their diagnose they don saw anything about this issue. Before its happen only when the weather is cold and car cold too but now while you on the road keep losing brake

NHTSA ID

11464873

Incident

Oct 22, 2018

Catastrophic brake failure. No brakes at all.

NHTSA ID

11455546

Incident

Mar 2, 2022

The brake handle popped off for parking brake

NHTSA ID

11455468

Incident

Mar 5, 2022

MY CAR WAS PARKED AND I ATTEMPTED TO OPEN THE DRIVER'S DOOR AS I WAS SEATED IN DRIVER'S SEAT AND I HEARD A LOUD POPPING NOISE. THE DOOR LOCK MECHANISM HAS FAILED SUCH THAT THE DRIVER'S DOOR CAN NOT BE OPENED FROM THE INTERIOR WHICH PRESENTS A SERIOUS SAFETY ISSUE. DESPITE BEING COVERED BY AN EXTENDED A MERCEDES CPO WARRANTY MERCEDES REFUSES TO COVER THE COST OF THE REPAIR. THIS IS A WELL KNOWN ISSUE ACROSS MANY MERCEDES MODELS INCLUDING THE R230 SL550. PART OF THE DOOR HANDLE ACTUATION MECHANISM IS MADE OF FRAGILE PLASTIC AND, OR NYLON THAT WEARS PREMATURELY.

NHTSA ID

10945750

Incident

Jan 15, 2017

Mileage

92,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Noises at the front axle when cornering or maneuvering (video files attached) Note: Save video files locally and play them with Windows Media Player. Cause Driving with summer tires in combination with low outside temperatures. At low outside temperatures or in wet conditions, a noise may be produced at the outer wheel on the front axle while maneuvering with sharp steering angles. Note: AMG vehicles with 4MATIC of model series 217 (without code 494) and model series 222 have a modified axle geometry compared with series production vehicles to provide more sporty handling. The problem cannot be remedied by changing the axle settings.

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system