1999 Chevrolet Sonoma

GENERAL MOTORS IS CONDUCTING A SPECIAL POLICY PROGRAM FOR 903,464 OWNERS OF 2000 - 2003 MODEL S/T VEHICLES THROUGH WHICH OWNERS MAY, AT THEIR OPTION, EITHER (1) PERIODICALLY INSPECT THE TAILGATE SUPPORT CABLES INSTALLED IN THEIR VEHICLE AND HAVE THE CABLES REPLACED IF THE CABLE COATING EXHIBITS ANY INDICATIONS OF DAMAGE OR DETERIORATION OR (2) REQUEST THAT THE TAILGATE SUPPORT CABLES BE REPLACED FREE OF CHARGE. GM WILL HONOR ALL REQUESTS BY OWNERS WHO OPT FOR REPLACEMENT WITHOUT QUESTION REGARDLESS OF THE CONDITION OR APPEARANCE OF THE CABLES. GM HAS AGREED TO MAIL REMINDER NOTIFICATIONS TO OWNERS EVERY TWO YEARS UNTIL THE TAILGATE SUPPORT CABLES HAVE BEEN REPLACED OR UNTIL THE VEHICLE IS 12 YEARS OLD.ODI'S INVESTIGATION INDICATES THAT A SIGNIFICANT MAJORITY OF THE REPORTED COMPLAINTS (87%) AND INJURIES (94%) HAVE OCCURRED IN MY 2000 - 2003 S/T VEHICLES.

ODI IS UPGRADING RQ04-012 AND OPENING AN EA TO INVESTIGATE THE TAILGATE SUPPORT CABLES INSTALLED IN 1998 - 2004 MODEL YEAR SONOMA AND S10 MODEL VEHICLES.GENERAL MOTORS IS CONDUCTING RECALL CAMPAIGN 04V-129 TO REPLACE THE TAILGATE SUPPORT CABLES ORIGINALLY INSTALLED IN CERTAIN MODEL YEAR 2000-2004 SIERRAS AND SILVERADOS AND CERTAIN MODEL YEAR 2002-2004 AVALANCHES AND ESCALADE EXTS (C/K MODELS).GENERAL MOTORS HAS ADVISED ODITHAT THE TAILGATE SUPPORT CABLES INSTALLED IN THE SUBJECT VEHICLES WERE FABRICATED USING IDENTICAL OR SIMILAR SHEATHING MATERIAL AS THE RECALLED VEHICLES.HOWEVER,GENERAL MOTORS HAS ADVISED ODI THAT SONOMA AND S-10 VEHICLES DIFFER FROM C/K MODELS IN SEVERAL WAYS: THE VEHICLE HEIGHT IS LOWER; THE TAILGATE DISPLACEMENT (DROP) WHEN NOT SUPPORTED BY THE CABLES IS SMALLER AND THE TAILGATE COMES TO REST AT A LESS SEVERE TIP ANGLE WHEN NOT SUPPORTED BY THE CABLES; THE TAILGATE MASS IS SMALLER; AND THE SIZE, PAYLOAD, AND USAGE CHARACTERISTCIS ARE LESS DEMANDING THAN C/K MODEL VEHICLES.GM ALSO STATED THAT SONOMA AND S-10 WARRANTY CLAIM INFORMATION INDICATES A LOWER CLAIM COUNT AND A LOWER CLAIM RATE THAN RECALLED C/K MODELS.NOTWITHSTANDING THE ABOVE INFORMATION, ODI HAS RECEIVED AN ADDITIONAL 73 NON-INJURY COMPLAINTS AND 10 INJURY COMPLAINTS ON THE SUBJECT VEHICLES DURING RQ04-012 (SINCE NOVEMBER 2004 TO DATE), WHICH JUSTIFIES OPENING AN ENGINEERING ANALYSIS TO FURTHER INVESTIGATE THIS ISSUE.

07-2007 WENT TO HAVE A FUEL INJECTION SERVICE DONE ON THE TRUCK AND THE TRUCK KEPT SHUTTING OFF. COULD NOT HOLD PRESSURE. FILLED THE TANK LAST NIGHT AND WHEN SLOWING OR STOPPED THE TANK READS EMPTY. *TR

NHTSA ID

10200499

Incident

Jul 12, 2007

DT: FROM THE DATE OF PURCHASE THE PARKING BRAKE FAILED. BRAKES HAVE BEEN READJUSTED SEVERAL TIMES. VEHICLE IS INSPECTED EACH YEAR, AND OWNER HAS TO REPAIR THE BRAKE SO IT CAN PASS INSPECTION. THIS COST LARGE AMOUNTS OF MONEY, AND GM WON'T COOPERATE WITH HIM.*AK

NHTSA ID

10125335

Incident

Jan 1, 2002

Mileage

7,000 mi

WHILE DRIVING VEHICLE WAS INVOLVED IN A HEAD ON COLLISION. UPON IMPACT, NEITHER OF THE AIR BAGS DEPLOYED. *AK

NHTSA ID

10055658

Incident

Jan 15, 2004

Mileage

46,000 mi

THE ABS BRAKING PUMP CONTINUES TO RUN WHILE THE VEHICLE IS TURNED OFF. THE DEALERSHIP IS AWARE OF THE PROBLEM. *JB *SCC

NHTSA ID

8018002

Incident

Aug 15, 2002

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.

Vehicle Recalls

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.

Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.