2008 Dodge Ram 2500

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

RMD opened this audit query (AQ) investigation in order to better understand and evaluate Chrysler's process(es) for timely and efficient execution of its safety recall campaigns, including its oversight and management of its parts division Mopar.Prior to opening this investigation, RMD had raised concerns with the company related to its execution of two safety recalls, 13V-528 and 13V-529, both of which involved safety defects that could cause the involved vehicles, FCA?s heavier Dodge Ram trucks, to lose steering control suddenly and without warning.Specifically, RMD inquired about the availability of parts for recall repairs, by email and phone on January 15, 2014 and February 19, 2014, due to the volume of complaints it was receiving from owners alleging parts scarcity and parts restrictions. FCA steadfastly denied it had placed parts restrictions on its dealers to manage issues of parts scarcity.FCA shared material showing it had uncommitted stock of parts available for its dealers. Nevertheless, consumer complaints of lack of parts continued.RMD made independent inquiries tosome dealers tobetter understand the conflicting claims between owners alleging lack of ability to repair their defective vehicles due to lack of parts, and FCA?s information showing availability of parts.Dealers informed and provided documentation to RMD on February 21, 2014 and February 25, 2014 showing FCA had, in fact, put into place parts restrictions and, further, had in some instances canceled dealerships? back orders for parts.In addition, during the course of its dialogue with dealers, RMD discovered that FCA had notified their dealerships on February 27, 2014 to return the recall remedy parts over quality concerns, and had therefore effectively canceled its safety recall program without notification to NHTSA. RMD issued a request for information (IR) on October 21, 2014.The company failed to respond to a number of the questions RMD asked that required it to produce specifics surrounding the repairs and parts ordering process with the recalls, including a question about whether a dealer order for recall parts could be canceled and under what circumstances.

ODI received complaints regarding failing tie rod ball studs on Model Year 2008-2011 Dodge Ram 2500 and 3500 vehicles resulting in loss of steering control.Chrysler concluded that misalignment of the left (driver side) ball stud on vehicles built with the Cross Car steering linkage system could allow contact between the bull stud and the ball housing which could weaken the stud and result in fracture.Chrysler submitted a recall notice on August 15, 2011 involving certain MY 2003-2011 Ram 2500 and Ram 3500 pickup trucks built or repaired with the Cross Car steering linkage.Chrysler will inspect, repair or realign the front end of the subject vehicles as needed.Chrysler's announcement of a safety recall on this matter addresses ODI's concerns.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10332525, 10357937, 10366591, 10303744, 10377166, 10373240, 10343969, 10375403, 10324831, 10373546, 10370771.

driving down the highway at 70 mph and the drivers door came opened it was caused by a faulty door lock actuator

NHTSA ID

11630223

Incident

Dec 11, 2024

I want to apologize for the lengthy description but I feel this is quite possibly the most critical area to not be vague in. **This problem occurs every time, NOT an intermittent condition.** REAR SEAT/CENTER SEAT BELT RETRACTOR; will not extend out from the retractor. The belt is locked in the fully retracted (unoccupied) position. The vehicle can be on a flat surface, an incline, or a declined position when this occurs. There's nothing obstructing any part of the belt and retractor. In order to use that position/seat belt, I must repeatedly (sometimes in excess of 20 times) pull the belt in different rates of speed ie. pull the belt very slowly, pull it normally, pull it very fast by basically snatching the belt. I've even tried to help the belt further retract into the retractor by slowly feeding the belt rearward. There's no 1 action that seems to work better than the other. Furthermore, at times, the belt (once able to be used) will not hold its position to keep the occupant from moving forward in a panic stop or even by snatching the belt to check its operation. The buckle does function as designed so this problem is strictly related to the shoulder belt not keeping the occupant secure. Apon visual inspection, there are no noted frays, stains, foreign objects, or signs of attempted (prior) repairs. I also want to note that I am an ASE certified Master Mechanic so I am well versed on the operation, diagnosis and replacement of seat belts/retractors/sinchers buckets etc. I'm asking for assistance by any information you can share with me to remedy this issue. This is my "daily driver" routinely using the back seat for my children. I don't want to replace it with a used part because I believe this is a common issue for this platform vehicle. Thank you for your time and assistance!

NHTSA ID

11526379

Incident

Jun 10, 2023

The contact owns a 2008 Dodge Ram 2500. The contact stated while driving various speeds, he started to smell exhaust fumes inside the cabin of the vehicle. The contact stated no warning light was illuminated. The vehicle was not diagnosed or repaired. A dealer was not contacted. The manufacturer had not been informed of the failure. The failure mileage was approximately 162,000.

NHTSA ID

11508674

Incident

Oct 1, 2022

Mileage

162,000 mi

during cold weather - when outside temp is below 30 degrees the wipers will not work. When outside temp is above 30 degrees wipers work. During a snow storm, driving home the wipers stop working and windshield freezes up. I replaced the multifunction switch and the wiper motor and dealer stated that the totally integrated power module could be bad. there is so many complaints about others having this issue. This is a major safety issue. Something needs to be done before someone is killed.

NHTSA ID

11450753

Incident

Feb 4, 2022

While driving the vehicle suddenly lost engine power and turned off. When this happened the steering column locked. It did not just loose power steering. The column itself entirely locked up. At this point the vehicle had no steering and limited breaking and went off the road. Thankfully it just went into a ditch and no damage was done. The vehicle turned right back on. The next day I recreated the problem on some friends property. I gave the keys in the ignition a small tug and the engine would stop and the steering column would lock. The ignition never rotated out of the on position and the key remained in the ignition. I recreated this probably 5 times and it did the same thing every time. I then brought it to the dealer but they didn't have the parts to repair it so I didn't have them look at it. I had to use the vehicle sooner then they could repair it to pull a camper about 1200 miles. I diagnosed the problem to be the ignition switch. I replaced the switch myself and the vehicle has not had the same problem since. I have given the keys in the ignition the same kind of tug and it is no longer a problem. I do have the switch available for inspection. I personally can totally understand the engine turning off due to an ignition switch failure but I believe the actual steering column locking is unacceptable.

NHTSA ID

11446616

Incident

Nov 10, 2021

The contact owns a 2008 Dodge Ram 2500. The contact stated while exiting out of the garage, the windshield defroster was activated and there was a loud clicking sound coming from the HVAC system. The contact stated that the HVAC system failed to switch over to the air vents. The contact inspected the vehicle and became aware that the defroster actuator was cracked inside in the vents causing the failure. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 109,000.

NHTSA ID

11439888

Incident

Nov 4, 2021

Mileage

109,000 mi

TL* THE CONTACT OWNS A 2008 DODGE RAM 2500. THE CONTACT STATED WHILE DRIVING 4 MPH, HE HEARD AN ABNORMAL SOUND COMING FROM THE VEHICLE. THE CONTACT STATED NO WARNING LIGHT WAS ILLUMINATED. THE CONTACT STATED THAT HE ATTEMPTED TO STEER TO THE VEHICLE TO THE RIGHT HOWEVER, THE VEHICLE FAILED TO RESPOND. THE VEHICLE WAS STOPPED IN THE MIDDLE OF THE ROADWAY. THE VEHICLE WAS NOT DRIVABLE. THE VEHICLE WAS TOWED TO HIS RESIDENCE. THE CONTACT CALLED COLORADO SPRINGS DODGE (7455 AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80923, (719)475-8550) AND THE DEALER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT DIAGNOSED NOR REPAIRED. UPON INVESTIGATION, THE CONTACT ASSOCIATED THE FAILURE WITH NHTSA CAMPAIGN NUMBER: 13V529000 (STEERING) HOWEVER, THE VIN WAS NOT INCLUDED. THE MANUFACTURER HAD NOT BEEN INFORMED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 289,000.

NHTSA ID

11413495

Incident

Apr 14, 2021

Mileage

289,000 mi

I WAS DRIVING ON I405 IN WASHINGTON STATE TRAVELING SOUTHBOUND WHEN I NOTICED SMOKE COMING FROM MY ENGINE COMPARTMENT...I PULLED OVER POPPED THE HOOD AND TOOK A QUICK LOOK.. I NOTICED FLAMES ON THE LOWER PORTION OF THE MOTOR ALMOST BEHIND THE FIREWALL...CALLED 911...

NHTSA ID

11361537

Incident

Sep 22, 2020

Mileage

180,000 mi

Trac-Rite Operation Diagnosis, Chatter, Shudder, Moving From A Stop And Turning

LAMP - DOME

Plate - Planetary

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.