2005 Ford Crown Victoria

The Office of Defects Investigation (ODI) opened an investigation concerning the loss of headlights in model year (MY) 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles. The subject vehicles share the same architecture and major components.ODI has received 636 unique reports (for all submission dates) related to the alleged defect, with owners describing a loss of both low and/or high beam headlights occurring while driving.ODI identified 4 Vehicle Owner Questionnaire ( VOQ) reports alleging minor crash or loss of control incidents due to headlight failures.Drivers alleged running off of the road due to a lack of headlights and one driver reportedly struck a deer.No injuries were indicated in the VOQ crashes.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 4173 unique reports related to the alleged problem.There were a total of 11 crashes reported within that group as well as one injury that occurred when the vehicle struck an unseen object on the side of the road when the headlights failed. Ford also submitted 49,843 warranty claims related to headlight failures.Most reports indicate that the headlights failed without warning leaving the driver with no forward lighting, however some noted the headlights flickered or dimmed prior to turning off.Consumers also noted they were able to hold the flash to pass lever on the steering column mounted stalk to activate the high beams however this is only effective as long as the lever is physically actuated.On December 21st, 2015 Ford notified ODI that it would conduct a safety recall (15V-861) to remedy headlight failures on (MY) 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles.According to Ford, the headlights of the vehicle are controlled by the Lighting Control Module (LCM) located in the engine compartment of the vehicle.The LCM uses an internal relay, mounted to a circuit board, to control power to the headlights. The headlight relay is soldered to the circuit board at six different terminals. The original equipment LCMs were manufactured in a manner that resulted in the solder joints fatiguing and/or cracking as a result of repeated thermal cycling and/or vibration, a defect condition. The condition could be exacerbated by manufacturing quality issues such as an insufficient amount of solder, effecting the continuity between the circuit board and the relay terminal, and resulting in loss of headlights while driving.Other lighting functions are unaffected by this condition.The LCM manufacturing processes were revised to address the defect condition and Ford has been conducting a warranty extension program to cover defective LCMs since late 2013.Under the recall Ford will replace any remaining defective LCMs in recalled vehicles with remedy LCMs once they become available.See NHTSA recall 15V-861 for further details on the safety recall.The recall action initiated by Ford addresses the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at SaferCar.gov under the identification (ODI) numbers found in the attached list.

In a letter dated October 2, 2014 the Office of Defects Investigation (ODI) was initially petitioned by the North Carolina Consumers Council, Inc. requesting a defect investigation of an alleged defect condition resulting in headlight and/or exterior lighting failure on 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles.ODI analyzed Vehicle Owner Questionnaire (VOQ) complaints received from consumers and identified a total of 605 reports (for all submission dates) alleging headlight failure.The complaints indicate failures of both low beam headlights typically while driving, a defect condition that was evaluated under a prior ODI investigation (PE08066).Most consumer VOQs indicate that the headlights failed suddenly and without warning leaving the driver with no forward lighting, however some report the headlights flickered or dimmed prior to turning off.In some cases drivers were able to turn the headlights back on after a period of time while others reported the headlights would not come back on at all.Consumers noted they were able to hold the flash to pass lever on the steering column mounted stalk to activate the high beams however this is only effective as long as the lever is actuated.ODI identified 4 VOQ reports alleging minor crash or loss of control incidents due to headlight failures.Drivers indicated running off of the road due to a lack of headlights and one driver reportedly struck a deer.No injuries were indicated in the VOQ crashes.In response to ODI's April 7, 2015 Information Request letter, Ford provided data indicating it has received 3,092 complaints of failed headlights related to the Lighting Control Module (LCM), a device that controls the headlights and other lighting functions.This number includes the complaints Ford reviewed and classified as headlight failure due specifically to the LCM.Within Ford's complaints, there are 11 reports alleging a crash occurred.These drivers reported hitting objects, including other vehicles after the headlights failed causing damage to the affected vehicles.One driver was injured when their car struck an unseen object in the road, jerking the steering wheel from their hands and injuring their shoulder.In total 15 crash allegations were identified, all of which have occurred since ODI's prior evaluation of this issue.This petition has been granted.Preliminary Evaluation PE15-028 has been opened to assess the scope, frequency, and safety-related consequences of the alleged defect.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SarchNHTSAID under the identification (ODI) numbers found in the attached list.

On July 7, 2014 the Office of Defects Investigation (ODI) opened a preliminary evaluation based on five complaints (VOQs) alleging incidents ofinterference between dislodged exhaust manifold heat shields and the lower steering shaft/knuckle, including one alleging the interference resulted in a crash on a highway entrance ramp. Since opening this investigation, ODI has received four additional owner complaints.One indicated that the shield was removed before binding could occur.The other three occurred at low speed and produced some momentary steering binding that was overcome by the driver when additional steering effort was applied.Once the shield was repaired or removed, the steering returned to normal.The single incident ODI identified as a possible crash (VOQ No. 10578715) related to this condition could not be verified and the description of the crash in the complaint was not supported by the police accident report.No additional crash allegations have been identified related to the alleged defect condition.Information provided by Ford in its September 10, 2014 response to ODI's information request letter identified 10 additional incidents resulting in a low rate of 1.6 incidents per 100,000 vehicles sold in vehicles ranging from 7 to 11 years in service.Six of these incidents were reported by a single source, a state police fleet that corrected the problems in March 2011 and has not reported any additional failures since.Ford also reported 5 warranty claims, but these incidents occurred at very low mileages and appeared to be caused by loose or missing heat shield attachment hardware rather than the corrosion condition that was the cause of the more recent incidents and the focus of this investigation.This investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency will continue to monitor complaints and other information relating to the alleged defect in the subject vehicles and take further action in the future if warranted.The following VOQs are associated with this investigation:10643753, 10615584, 10611362, 10610451, 10578715, 10479681, 10471833, 10317493.

In its recall notice dated August 26, 2013, Ford Motor Company (Ford) notified NHTSA of a safety defect condition that may result in loss of steering in approximately 355,000 model year (MY) 2005 through 2011 Ford Crown Victoria and Mercury Grand Marquis vehicles built at the St. Thomas Assembly Plant, MY 2005 through 2007 Lincoln Town Car vehicles built at the Wixom Assembly Plant, and certain MY 2008 through 2011 Lincoln Town Car vehicles built at the St. Thomas Assembly Plant and that are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, or Wisconsin (NHTSA Recall 13V-385, Ford Recall 13S08).Ford's recall addresses a corrosion related defect in the lower intermediate shaft that may result in separation of the steering column lower bearing and loss of steering control.Ford's recall will remedy the defect condition by instructing dealers to replace the lower intermediate shaft and to inspect and repair the upper intermediate shaft and steering column lower bearing as necessary.A retaining clip will be installed if the lower bearing has separated.Ford's investigation of steering column separations in the subject vehicles identified a defect condition in the lower intermediate shaft that could result in separation of the column lower bearing.According to Ford's August 26th defect report, severe corrosion of the lower intermediate shaft may cause the lower intermediate shaft swing link joint(s) to stiffen or seize.Ford determined that forces acting on the upper intermediate shaft because of seized swing links may eventually cause the upper intermediate shaft to collapse, which may result in separation of the column lower bearing and loss of steering control.Analysis of ODI complaints and Ford complaints and warranty identified 22 incidents of steering separation (12 complaints and 10 non-duplicative warranty claims) that may be related to the lower intermediate shaft defect condition.All 22 incidents involved vehicles in the recall region, where 419,210 or roughly half (52%), of the subject vehicles were sold.Ford's investigation also determined that column lower bearing separation may occur in vehicles that experienced upper intermediate shaft collapse in prior frontal impact collisions if the shaft was not properly diagnosed and repaired.Ford identified 13 steering separation incidents outside the recall region (6 complaints and 7 non-duplicative warranty claims) where 386,003 of the subject vehicles were sold.Ford did not find evidence of the lower intermediate shaft corrosion issue in these vehicles.Six of the vehicles had known prior collisions and the histories of the remaining 7 were unknown.To address concerns with possible steering separations in vehicles outside the region for safety recall 13V-385, Ford is conducting a Regional Program (13R01) to inspect and repair the steering assemblies of those vehicles as necessary.The lower intermediate shaft will be replaced only if it fails the inspection, the upper intermediate shaft will be repaired if it fails a Ford-specified measurement test.In the event the steering column lower bearings are found out of position, they will be re-seated and secured with a retaining clip.Based on Ford's field actions, this investigation is closed.The VOQs cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10505992, 10479893, 10477192, 10475950, 10474596

The contact owns a 2005 Ford Crown Victoria. The contact stated that the headlights had become intermittently inoperable while driving at night. The contact personally replaced the fuses and undisclosed parts, per the information found online; however, the failure persisted. The odometer was inoperable. The dealer was contacted and informed that the vehicle had been previously repaired for the failure. The manufacturer was contacted, and a case was filed, but assistance was denied. The vehicle was not repaired. The failure mileage was unknown.

NHTSA ID

11720404

Incident

Feb 25, 2026

In October 2022 a mechanic successfully replaced a dark gray-colored "seat belt retractor assembly and buckle" on the passenger side of my Ford Crown Victoria in response to an Air Bag dashboard light Lamp Fault Code of "3-4" and a Diagnostic Trouble Code of "B2292" ("Restraint System Seatbelt Pretensioner Error"). Such an error renders the entire supplemental restraint system inoperative and necessitates immediate repair service for safe vehicle operation. In September 2023 the Air Bag light displayed a "3-3" LFC with the "B2292" DTC indicating Restraint System Seatbelt Pretensioner Error on the driver's side. The mechanic and I contacted a Ford dealership for a replacement dark gray-colored seat belt retractor assembly and buckle and were advised that Ford had discontinued manufacture of the part in dark gray and other colors! Ford only offered a tan seat belt assembly. It seemed irresponsible that Ford would discontinue production of such a vital safety part for a vehicle that is used as a personal vehicle, as well as a fleet vehicle for law enforcement organizations, and for state and municipal governments. Without a replacement I could not even pass the state safety inspection to sell the vehicle. To continue to operate the vehicle safely I have no choice but to have a tan seat belt and its accompanying tan interior components installed in a vehicle with a dark gray interior. Please exert whatever influence you have to compel the Ford Motor Company to resume production of the dark gray and other colors of the seat belt retractor assembly and buckle. Thanks.

NHTSA ID

11546047

Incident

Sep 21, 2023

Safety recall for the LCM was repaired by lameroux Ford in Brookfield but the bypass was not preformed and the lcm is still acting up. Called and they want to charge me to look at the work they failed to do properly. Brought it to another mechanic who verified the LCM was not bypassed.

NHTSA ID

11538603

Incident

Feb 15, 2021

Steering wheel hard to turn

NHTSA ID

11525761

Incident

Jun 7, 2023

Power steering went out when I was driving and barely avoided a collision. Light went out another time when I was driving.

NHTSA ID

11523122

Incident

Sep 14, 2022

Safety Recall 19S35b Processor Lighting cont was done on 3/22/2021on my working part. The original module was working fine. Now the new light module is faulty. Dealership took out part and tested it. Determined that is was faulty causing my lights to fail. Dealership and Ford has denied covering a replacement of the failed part. It would seem that the part should be still covered since it is a part that was part of a recall.

NHTSA ID

11488668

Incident

Sep 29, 2022

The contact owns a 2005 Ford Crown Victoria. The contact stated that while operating the vehicle, the front headlights became inoperable creating a visibility hazard for the driver. The cause of the failure was not yet determined. The local dealer was notified of the failure and informed that the vehicle needed to be diagnosed. The contact was informed that the failure might not be related to NHTSA Campaign Number: 15V861000 (Exterior Lighting). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was unknown.

NHTSA ID

11485162

Incident

Sep 19, 2022

Unknown the ride feels unsafe to travel around inn

NHTSA ID

11447986

Incident

Jan 1, 2022

This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.

Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition

The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.

Inpected or repaired under 13R01 - Requests for recall service action under 13S08

For 2005-2012 Crown Victoria, 2005-2011 Grand Marquis and Town Car vehicles, Regional Program 13R01 applies to vehicles not registered in corrosion states and not included in Safety Recall 13S08, where operation in high corrosion areas for an extended period may lead to corrosion in the lower intermediate steering shaft swing link. This may result in a compressed upper intermediate steering shaft and separation from the steering column, which can result in a loss of steering control. Vehicles covered under 13R01 that were inspected or repaired without replacement of the lower intermediate shaft, and have relocated to high corrosion areas, may experience subsequent corrosion of the lower intermediate steering shaft swing link.