2005 Jeep Liberty

ODI has completed an extensive analysis of rear crash fuel tank system integrity data for the subject Jeep Cherokee, Grand Cherokee and Liberty vehicles (SVs).As of June 2013, ODI knew of 56 post-collision fatal fires, 28 non-fatal fires, and 6 fuel leak incidents (totaling 90 incidents, 75 fatalities and 58 injuries) involving the SVs.Based on this analysis, ODI issued a Recall Request Letter (RRL) on June 3, 2013 requesting that Chrysler recall the Grand Cherokee and Liberty vehicles due to the rate of fatal, non-fatal fire, and fuel leak incidents when compared to peer vehicles (compact and medium SUVs) built during the same time period.In the RRL, ODI described how the location of the aft-mounted fuel tank made the SVs vulnerable to rear impact crash fuel tank failures.During the analysis, besides the high speed/high severity crashes present in both the SV and peer vehicles, ODI observed a significant number of low and moderate speed rear impact crash related fires and leaks, particularly in the Liberty.The data also demonstrated that SVs originally equipped with towing hitch receivers (trailer hitches) appeared to be under-represented in rear-impact related fuel tank failures.In the RRL, ODI requested that Chrysler provide its response by June 18, 2013, otherwise NHTSA might proceed to an Initial Decision that the SVs contain a safety-related defect.Chrysler responded to the RRL on June 4, 2013 and vigorously disputed the tentative findings of the RRL.Among other things, Chrysler argued that the SVs had an overall safety record superior to their peers, met or exceeded all applicable federal motor vehicle safety standards (FMVSS) and only experienced fires in severe high energy rear impacts.Nonetheless, while continuing to maintain that the SVs did not contain a safety-related defect, Chrysler proposed a recall (13V-252) of approximately 2.5M (1.6M currently registered) model year (MY) 1993 - 1998 Grand Cherokee (ZJ) and MY 2002-2007 Liberty (KJ) vehicles on June 18, 2013.The recall remedy submitted by Chrysler would employ a hitch receiver assembly consisting of a steel cross-member behind the fuel tank with forward-projecting arms bolted to the frame rails on either side of the fuel tank.For the MY 1999 - 2004 Grand Cherokee, Chrysler indicated it would conduct a customer satisfaction campaign and inspect vehicles equipped with aftermarket tow hitch receivers, and if necessary, replace any such hitch receivers whose conditionmay increase the risk of fuel system failure in rear crashes.Examination of the available data established that the MY 1999 - 2004 Grand Cherokee did not pose the same magnitude of safety risk as the MY 1993 - 1998 Grand Cherokee and MY 2002-2007 Liberty, particularly in low and moderate speed rear impacts.Because the agency has concluded that the vehicles do not present an unreasonable risk to safety, ODI is closing its investigation of the MY 1999 - 2004 Grand Cherokee.Although it was not within the scope of the Petition initiating this investigation or the Preliminary Evaluation preceding this EA, ODI also examined the performance of the MY 1993 - 2001 Cherokee as part of this investigation.NHTSA's assessment of the available data for the Cherokee did not establish an unreasonable risk in comparison to peer vehicles.ODI does not approve proposed defect remedies.While offering to install hitch receiver assemblies on the MY 1993-1998 Grand Cherokees and 2002-2007 Liberty, Chrysler did not, in ODI's view, provide enough evidence demonstrating the effectiveness of the proposed remedy in rear impacts.The Complete Summary for this Closing Resume (EA12-005) can be seen by

In a letter dated March 2, 2012 Chrysler Group LLC (Chrysler) submitted a Defect Information Report (NHTSA recall No. 12V-085) to the NHTSA identifying a safety defect regarding rear suspension lower control arm corrosion in approximately 210,000 model year (MY) 2004 and 2005 Jeep Liberty vehicles, originally sold or currently registered in a Salt-belt state (Connecticut, Delaware, Iowa, Illinois, Indiana, Kentucky, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia).According to Chrysler, excessive corrosion could result in fracture of a rear suspension lower control arm which may result in a loss vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Chrysler, ODI identified 54 non-duplicative reports alleging failure of one or both rear lower control arms due to excessive corrosion.Thirteen of these complaints allege that the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional 11 complaints reported difficulty maintaining control of the vehicle when the rear lower control arm failed.All of the complainant vehicles were either originally sold or registered at the time of the incident in a Salt-belt state.ODI did not identify any reports (complaints or warranty claims) related to rear lower control failure due to excessive corrosion in the approximately 138,000 MY 2004 and 2005 Liberty vehicles that are not included in this recall (i.e., not sold or currently registered in a Salt-belt state).In Chrysler?s Defect Information Report, Chrysler stated that during the investigation a field survey of MY 2004 and 2005 Jeep Liberty vehicles was conducted.In total, Chrysler is aware of 83 incidents alleging rear control arm fracture (including complaints and field study results).Based on Chrysler?s decision to conduct a safety recall this investigation is closed. The associated VOQs are: 10449912, 10448981, 10448406, 10448119, 10447069,10446737, 10445029, 10443863, 10443222, 10441248, 10438681, 10437308, 10436416, 10436231, 10436024, 10434927, 10434157, 10433963, 10430852, 10429346, 10428006, 10427087, 10426644, 10426393, 10419094, 10417697, 10416623, 10410148, 10409668, 10402048, 10397413, 10392160, 10388448, 10365118, 10360057, 10360049, 10345985

During Preliminary Evaluation (PE11-013), the Office of Defects Investigation (ODI) conducted an analysis of consumer field data from its Vehicle Owner Questionnaire (VOQ) database and from complaint data submitted to ODI by Chrysler. ODI's analysis of VOQ data identified 13 complaints alleging failure of either the right or left rear lower control arm due to excessive corrosion.All of these complaints were associated with vehicles originally sold or registered in a salt belt state (for the purposes of this investigation, 'salt belt' includes Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia).All of the complaints were associated with vehicles manufactured in model years (MY) 2004 or 2005. Three of these complaints also allege a loss of vehicle control due to the rear lower control arm failure. No complaints related to the alleged defect were identified on vehicles manufactured during MYs 2002 or 2003. Similarly an analysis of Chrysler complaint data identified 11 complaints (2 of which are duplicative of VOQs) alleging failure of a rear lower control arm due to excessive corrosion.All 11 of these complaints were from consumers operating vehicles in a salt belt state and vehicles manufactured in either MY 2004 or 2005. Three of these complaints (not duplicative of VOQs) also allege a loss of vehicle control due to the rear lower control arm failure.The original scope of PE11-013 included MY 2002 through 2005 Jeep Liberty vehicles as they were in the same generation.In response to an Information Request (IR) letter sent by ODI, Chrysler provided information and sample components identifying a substantial design change of the rear lower control arms after MY 2003 and beginning with MY 2004.Analysis of complaint data from both data sources (ODI and Chrysler) did not identify any applicable complaints (lower control arm failures due to excessive corrosion) from vehicles manufactured during MY 2002 or 2003.Similarly no complaints from either data source were found in states outside of those identified as salt belt states.Chrysler stated in its IR letter response that its investigation and analysis is ongoing to determine the scope, possible root causes of the unusual lower control arm corrosion, and define possible consequences to motor vehicle safety. Based on ODI's data analysis from both sources (ODI and Chrysler data), this investigation has been upgraded to an Engineering Analysis (EA11-013) focused on vehicles originally sold or registered in a salt belt state and produced during MY 2004 and 2005, to further assess the scope and potential safety consequences of the alleged defect.

OVERHEATING OF THE ELECTRICAL CONNECTOR AT THE FUEL HEATER ON THE FUEL FILTER / WATER SEPARATOR ASSEMBLY CAN CAUSE A FUEL LEAK THROUGH THE ELECTRICAL CONNECTION.OPERATORS REPORT THE SMELL OF DIESEL FUEL, SMOKE, DIFFICULTY STARTING AND/OR POOR ENGINE OPERATION.THE FUEL LEAKAGE IS REPORTED BY SOME OPERATORS AS SEEPAGE, WETNESS, SEVERAL DROPS, AND AN OZ PER MINUTE.EVIDENCE OF OVERHEATING OF THE CONNECTION WAS OBSERVED BY SOME OPERATORS AND REPORTED AS BURNED OR DISCOLORED ELECTRICAL CONNECTION AT THE FUEL HEATER.SEVEN OPERATORS REPORT SMELLING OR SEEING SMOKE.ONE REPORTED A VEHICLE ENGINE COMPARTMENT FIRE HOWEVER THE CAUSE OF THE FIRE WAS NOT IDENTIFIED, AND LINKAGE OF THE FIRE CAUSE TO THIS ISSUE IS NOT LIKELY TO BE ESTABLISHED.THE LOCATION OF THE FUEL FILTER / WATER SEPARATOR ASSEMBLY IS NOT NEAR THE LOCATION OF THE TURBO CHARGER WHICH IS LOCATED ON THE OPPOSITE SIDE OF THE ENGINE.THE TURBO CHARGER WOULD PRESENT A POTENTIALLY HOT SURFACE HOWEVER DUE TO THE LAYOUT OF THE ENGINE COMPARTMENT AND ITS COMPONENTS, DIESEL FUEL LEAKAGE FROM THE ELECTRICAL CONNECTION WOULD NOT LIKELY MIGRATE TO THE TURBO CHARGER.AT THIS TIME, A SAFETY-RELATED DEFECT TREND HAS NOT BEEN IDENTIFIED AND THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY DEFECT DOES NOT EXIST.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.

i recieved the car from a private party and he stated no issues but since older car and now registration is due it states theres still an open recall is this vehicle still covered for it?

NHTSA ID

11726196

Incident

Oct 1, 2025

The ball joint broke while I was driving I lost all control of vehicle

NHTSA ID

11694634

Incident

Sep 8, 2025

The contact owns a 2005 Jeep Liberty. The contact stated that while driving at an undisclosed speed, the contact noticed an abnormal sound coming from the vehicle, and the vehicle was shaking erratically. No warning lights were illuminated. The vehicle was towed to the dealer, where it was diagnosed with transfer case and transmission failure. The contact was informed that the transfer case and the transmission needed to be replaced. The vehicle was in the process of being repaired. The contact researched NHTSA Campaign Number: 18V278000 (Suspension). The manufacturer was made aware of the failure and a case was filed. The contact was advised to submit the repair documents regarding the failure. In addition, the contact was informed that the replacement of the transfer case and the transmission replacement were not covered under the recall. The contact was advised to contact the NHTSA Hotline and report the failure. The failure mileage was approximately 200,000.

NHTSA ID

11690719

Incident

Sep 22, 2025

Mileage

200,000 mi

Today 6/16/2025 I’m having trouble turning to the right and left leaving from a stop sign we checked to be sure power steering fluid is full and it is. The person who checked the power steering fluid level, said that there is rubber grommets under the hood with the suspension and staring that look like they are all decayed or dry rotted. I have not had a problem with it breaking yet, but I’m sure that’s coming. Not sure it’s safe to drive.

NHTSA ID

11667311

Incident

Jun 16, 2025

I was driving on a bridge and my ball joint broke. Blew a hole through my tire and my rim and the fender flare blew off. I had had that same ball joint replaced approximately two years prior maybe sooner. I got this Jeep in 2017 and I have replaced the driver side ball joint twice the passenger side ball joint once and the ball joints look bad again.

NHTSA ID

11667307

Incident

Oct 1, 2022

About 6 months ago the passenger side front end to hit the ground, just after going 60 miles an hour thankfully turning in daughter's driveway. Lower ball joint passenger side came apart. On Monday doing 35 mph the driver side hits the pavement hard! Luckily I ditched in a driveway on the left! The tire slammed into the fender well breaking the plastic there and the piece that goes back under the doors? Ball joint broke completely into? I'm on my third day of working in the rain alongside a road repairing this?

NHTSA ID

11566413

Incident

Jan 15, 2024

The contact owns a 2005 Jeep Liberty. The contact stated while driving approximately 70 MPH, the vehicle swerved to the left across three lanes of traffic and the contact turned the steering wheel to the right to prevent the vehicle from veering to the left. The contact then stopped on the shoulder of the highway. The contact stated there was no warning light illuminated. The contact stated that the Police were on scene and determined that the vehicle could not be driven. The contact stated the Police Officer picked up the ball joint that had detached from the driver’s side front suspension of the vehicle. The vehicle was towed to the residence. The vehicle had not been taken to a dealer or independent mechanic. The vehicle was not diagnosed or repaired. The contact researched online and related the failure to NHTSA Campaign Number: 06V288000 (Suspension). The manufacturer was not informed of the failure. The failure mileage was approximately 225,000.

NHTSA ID

11561064

Incident

Dec 18, 2023

Mileage

225,000 mi

P235/70R16 The car was parked, when I left on the morning of July 14 to go to work, it had already exploded. I thought it was the excess heat but the strange thing was the separation that occurred.

NHTSA ID

11532507

Incident

Jul 14, 2023

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Mechanical rocker arm, intake, 1.7 ratio.

Mechanical rocker arm, intake, 1.7 ratio.

KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.