2019 Mercedes-Benz AMG GLE43

On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183

The contact owns a 2019 Mercedes-Benz AMG GLE450. The contact stated that while driving approximately 70 MPH, there was an abnormal banging sound coming from the roof. While looking in the rear-view mirror, the contact saw a dislodged trim piece striking a vehicle behind. After stopping to inspect the vehicle the contact discovered that the plastic front roof panel trim piece had detached from the vehicle. No further info was available regarding the second vehicle. The cause of the failure was not yet determined. The manufacturer and local dealer were notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in NHTSA Campaign Number: 23V854000 (STRUCTURE). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 52,000.

NHTSA ID

11744175

Incident

Jun 14, 2026

Mileage

52,000 mi

The P06DA00 code in Mercedes-Benz vehicles is a common issue involving the oil pump solenoid, often caused by a faulty wiring harness. If this is caused by faulty wiring harness then this should be a recall since it is common and happens to all vehicles like mine. I have been told that this needs to be a recall. Oil Pump Gear: Found faulty oil pump control valve present and requires replacement. Recommend replacement of engine oil pump control valve. The oil pump gear is attached to the oil pump shaft and used to spin the oil pump. The oil pump is used to circulate the engine through the engine.

NHTSA ID

11730457

Incident

Apr 10, 2026

Panaramic glass roof exploded while traveling on highway sending glass all over the car and highway. Sounded like a gun shot right above my head. Fortunately the sunshade was closed at the time and I was able to safely exit the highway to clean up the mess and no one was injured but it could have been very dangerous!

NHTSA ID

11724315

Incident

Mar 13, 2026

The contact owns a 2019 Mercedes Benz AMG GLE43. The contact stated while driving 55 MPH, there was a whistling sound coming from the sunroof. The contact stated that while taking an exit, the roof panel detached from the vehicle. The contact stated that a dealer was contacted. The vehicle was taken to the dealer where it was determined that the roof panel needed to be replaced. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 21V197000 (STRUCTURE); however, the VIN was not included in the recall. The manufacturer was notified of the failure but offered no assistance. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was 63,754.

NHTSA ID

11669793

Incident

Jun 24, 2025

Mileage

63,754 mi

The contact owns a 2019 Mercedes-Benz AMG GLE43. The contact stated while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle returned to normal functionality, but the failure became a regular occurrence. The vehicle was taken to the dealer, who diagnosed a failure with the engine oil pump control solenoid, resulting in possible damages to the engine. The vehicle was not repaired. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 100,000.

NHTSA ID

11667447

Incident

Jun 17, 2025

Mileage

100,000 mi

My safety and others safety was put at risk when I was driving on the freeway. The front glass panel between the windshield and panoramic sunroof detached from the vehicle. It sounded as if the entire sunroof shattered and something crashed into the vehicle causing myself to swerve, duck for cover and nearly crash into the median causing a near accident with my passenger as a witness. The car directly behind me was noted to swerve almost hit the median following the noise. In the moment I had no idea what happened until I had to pull off the freeway to assess what happened. This is when noted the the front panel between the windshield and panoramic sunroof was noted to be broken off. The vehicle was recently inspected by an official Mercedes Benz service department prior to this and then by an official Mercedes Benz Body Shop following the damage. There was no warning lamps or any symptoms or signs of damage prior to this failure. There is several noted recalls on other VIN models for Mercedes GLE 43 for this exact same issue of failure to this specific front roof panel but for some reason my vehicle VIN is not included. It is noted that the front roof panel between the windshield and panoramic roof may not have been bonded on correctly or the bond can deteriorate and can detach from the vehicle causing a road hazard and increasing risk for a crash.

NHTSA ID

11666196

Incident

May 3, 2025

I had reported prior about My engine light warning. I now have a letter stating that the warranty on this was extended due to a recall that applies to my vehicle. I would like to add that my vehicle is a AMG and shows a different vehicle in your system when I enter the vin number.

NHTSA ID

11665055

Incident

Jun 3, 2025

NHTSA Campaign ID: 23V854000 is an expansion of campaign ID 21V197000 but is still too narrowly focused and needs to have the investigation re-opened. While driving at highway speed the glass panel on the body that is attached between the windshield and panoramic sunroof experienced an unexpected and total adhesive failure causing the glass body panel to become airborne and projectile at highway speed. Luckily it landed on the highway and shattered without injury. The two recall campaigns reference this exact failure on cars where the panel has been previously replaced, however there is no information to suggest the original need for a previous repair. In this case, the vehicle did not have a previous repair on record, yet Mercedes claims this problem only exists in previous repair scenarios and refuses to complete the repair under the recall. Logically, one of these two things MUST be true: 1.) The adhesive failure is born from the assembly process in the factory, in which case the recall should be expanded under the same safety concerns as the previously cited campaigns and Mercedes should be compelled to make the repair. 2.) There was a previous repair done to this glass on the vehicle and proper records were not maintained by Mercedes, in which case it falls into the scope of the previously cited campaigns and Mercedes should be compelled to make the repair. I attempted to work directly with Mercedes on this but after escalation, they denied the request for repair under courtesy repair or under recall scope. I'm hoping for help from the NHTSA as simple logic suggests that either the vehicle should already be in scope of the recall, or that the recall scope is too narrow and was not properly investigated. Mercedes attempted several illogical excuses in an attempt to avoid responsibility, but they strained credulity at best. This same complaint even appears several times on the NHTSA page for this vehicle make/model, and the report doesn't list VIN.

NHTSA ID

11665011

Incident

May 1, 2025

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Dear Mercedes-Benz Owner: In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA is extending the warranty coverage for the Diagnostic Module for Tank Leakage Detection ("DMTL") on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first). This applies to the vehicle regardless of ownership. Why the Warranty extension? On certain Model Year 2018 - 2024 A / C / CLA / CLS / E / G / GLA / GLB / GLC / GLE / GLS / GT / S / SL Mercedes-Benz vehicles, under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code ("DTC") entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp ("MIL"). Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. • If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. • This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.

Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint This document is intended as a pre-case diagnostic reference for transmission related concerns. It will also ensure that if a case is necessary, all supporting documentation is available. This should not be used on its own as justification for creating a TIPS case. Cause The root cause will vary depending on the complaint. The goal of this document is to provide diagnostic checks and procedures that may help resolve customer complaints without opening a TIPS case. Remedy Before opening a transmission-related TIPS case, the following steps must be performed to ensure all relevant data has been collected and possible remedies (when applicable) have been performed. Please Note: At minimum, the documents below must be collected before proceeding to ensure the data in its original state when the vehicle arrived is captured. - Initial Quick Test w/ Freeze frame data - VGS Control Unit Log - Initial EEPROM data (.txt format) - IPR Result (if applicable. See LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool) - Transmission Heath Page If the vehicle has previously been repaired for the same concern, note the date, mileage, and TIPS case or RO number, along with a brief description of the prior work performed. IPR Guidance: The IPR recommended repair should be completed prior to following any steps in this LI and prior to case creation. IPR repairs do not require additional warranty approvals or a TIPS case to validate/confirm the results. To ensure efficient case handling, please avoid opening TIPS cases for this reason. For further information regarding IPR please see the following documents: LI27.00-P-073124 - Transmission diagnosis using the Intelligent Predictive Repair (IPR) tool Oil Pan Condition Evaluation: In some situations, IPR will advise checking the oil pan condition and determining a repair based on the evaluation. Example photos in Xentry can be found in two ways: • Use the blue hyperlink in the IPR result, and it will take you to the Condition check of transmission oil • Navigate to Xentry Bluebook > Help for control unit > Condition check of transmission oil If a different repair that what is recommended by IPR is performed, attaching photo documentation of the complaint vehicle oil pan and the IPR example to the claim is required. Reproducing the Concern: Proper evaluation of transmission concerns generally requires the condition to be reproducible. It is recommended to compare the vehicle to a similar model, if available, to help determine whether the shift behavior is characteristic of the drivetrain or uncharacteristic for the vehicle. If the concern cannot be duplicated: • A test drive with the customer may assist in understanding and reproducing the complaint. • The vehicle shift quality should be compared to a known-good vehicle with identical drivetrain and model year. • Check Shift Quality History (VGS Control Unit > Adaptations > Shift Quality History) Shift Quality History will show the last 5 noticeable harsh shifts and some of the parameters in which it occurred. You can use this to attempt recreation of the operating conditions and increase likelihood of reproducing the complaint. Complaint A: Shift Quality Note: Certain AMG variants may exhibit more firm and noticeable shift behavior as a normal characteristic. Refer to LI27.60‑P‑075147 for additional information. 1. Perform Valve flushing procedure 2. Perform 5 Torque Converter adaptions in a row - Allow the vehicle to warm up naturally, DO NOT power brake as it will increase the temperature in the torque converter. - After the 5th adaptation, collect a screen shot showing all 5 on one page 3. Perform a standstill adaption - collect a screen shot Recheck vehicle operation. If the concern has not improved, driving adaptations should be performed to target specific gear shifts.

Complaint Mercedes-Benz USA is currently experiencing limited availability of transmission fluid specification ATF 236.17 due to a global supply constraint. 236.17 ATF 1L and 5L (PNs: A002989060312 and A002989060313) bottles are out of stock or in limited supply at Zep. This LI has been created with the following intention: - Provide dealers with additional workshop-focused guidance regarding the current ATF 236.17 supply constraint and the planned introduction of ATF 236.18. - Supplement existing communications and address common workshop questions related to maintenance, repairs, and fluid applicability. - Provide technical clarification and practical workshop guidance during the temporary supply constraint period. Dealers should continue to reference the latest News Channel Updates (NCUs) for the most current information regarding availability, ordering processes, supply status, and other related updates. Cause Damage to the Shell production facility has resulted in 236.17 oil supply being reduced to 50% of normal output until the end of 2026. Remedy Please first check Latest NCU updates for latest detailed information. Please continue placing orders through Paragon as normal. Supply is expected to remain reduced and allocation measures are currently in place. We ask for your patience through this restricted supply period. Most orders will be filled in the order in which they were received, as supply is replenished. Those dealers with zero inventory, and pending orders, will receive priority. We expect supply to be stabilized in September 2026. Approved Fluids: Only use transmission fluid from the approved list found on the Mercedes-Benz Operating Fluids website. Non-approved fluid will result in mechanical damage to the transmission and must be avoided. https://operatingfluids.mercedes-benz.com/sheet/236.17 Approved fluids can be claimed as follows if there is no Mercedes-Benz part number: Part # ATFSUB1L - TRANSMISSION FLUID 1 LITER ATFSUB5L - TRANSMISSION FLUID 5 LITER Dealerships with Zero Inventory AND Grounded Vehicles: If a vehicle is currently grounded for repair at your dealer due to no 236.17 inventory, we may be able to expedite your order. Please open a StarSupport ticket including the following information: (Parts Related Inquiry>National Accounts>Zep) • LI document number • Short explanation of repair needed for grounded vehicle • Current days down of RO Maintenance and Service Interval Guidance Published maintenance intervals remain unchanged. Vehicles should continue to be maintained in accordance with the applicable maintenance schedule. This LI does not revise or extend any published maintenance interval requirements. If all required parts and materials are not available prior to scheduling or beginning a transmission service, dealers should consider postponing routine preventative transmission maintenance until the necessary parts become available. For vehicles that have not yet reached the applicable maintenance interval and do not exhibit transmission-related concerns, there is no need to recommend preventative transmission services prior to the scheduled maintenance interval. When evaluating whether routine transmission maintenance can be deferred until parts become available, dealers should consider: • Overall vehicle condition • Vehicle usage and operating conditions • Presence of transmission-related symptoms or customer complaints • Customer expectations and vehicle operating requirements • Availability of required parts and materials Introduction of New Fluid Specification 236.18 Mercedes-Benz is currently preparing the introduction of ATF 236.18 as an additional approved transmission fluid solution for applicable NAG3 transmissions. At the time of publication of this LI, ATF 236.18 is not yet available for dealer ordering or workshop use in the U.S. market. See attachment for further details.