2008 Mercedes-Benz CLK350

TL* THE CONTACT OWNS A 2008 MERCEDES-BENZ CLK350. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V918000 (VISIBILITY) HOWEVER, THE PART TO DO THE RECALL REPAIR WAS NOT YET AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. MERCEDES-BENZ OF ROCKVILLE CENTRE (650 SUNRISE HWY, ROCKVILLE CENTRE, NY 11570) WAS CONTACTED AND CONFIRMED THAT PARTS WERE NOT YET AVAILABLE FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN WAS NOT AVAILABLE.

NHTSA ID

11362009

Incident

Sep 1, 2020

MANY OWNERS OF LATE-MODEL MERCEDES-BENZ CARS EQUIPPED WITH 3.0L AND 3.5L V6 ENGINES (M272 OR M273) HAVE EXPERIENCED PERFORMANCE PROBLEMS THAT INCLUDE POOR IDLE, LOSS OF POWER AND A CHECK ENGINE LIGHT WITH A P2006 CODE (OR SOMETIMES OTHER CODES). THE SHAFTS WILL FAIL INSIDE THE MANIFOLD AND BIND, CAUSING THE LEVER TO BREAK AND THE CAPS SHOWN TO LOOK LIKE THEY ARE POPPING OFF THE MANIFOLD.

NHTSA ID

11361155

Incident

Mar 2, 2017

Mileage

130,000 mi

TL* THE CONTACT OWNS A 2008 MERCEDES BENZ CLK350. THE CONTACT STATED THAT WHILE DRIVING AT VARIOUS SPEEDS, THERE WAS AN ABNORMAL RATTLING NOISE COMING FROM THE SUNROOF. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V918000 (VISIBILITY) HOWEVER, THE PART TO DO THE RECALL REPAIR WAS UNAVAILABLE. MERCEDES-BENZ OF ROCKVILLE CENTRE 650 SUNRISE HWY, ROCKVILLE CENTRE, NY 11570 WAS CONTACTED AND CONFIRMED THAT THE PART WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND THE CONTACT WAS INFORMED THAT THE VEHICLE SHOULD NO LONGER BE DRIVEN UNTIL THE RECALL REPAIR WAS PERFORMED. THE FAILURE MILEAGE WAS 40,000. THE VIN WAS NOT AVAILABLE.

NHTSA ID

11325411

Incident

May 3, 2016

Mileage

40,000 mi

PURCHASED FROM PRIVATE INDIVIDUAL WITH MILEAGE 43,000. FILLED UP THE GAS TANK ON TWO OCCASIONS. AFTER EACH OCCASION, PLACED CAR IN GARAGE AFTERWARD AND CLOSED GARAGE DOOR. THE SMELL OF RAW GAS WAS OVERWHELMING AS SOON AS GARAGE DOOR WAS SHUT. DUE TO THE OVERWHELMING SMELL AND SAFETY CONCERN, CAR WAS PARKED IN DRIVEWAY. NO LEAKS ON GARAGE FLOOR WERE FOUND. CAR PARKED IN GARAGE THE NEXT DAY WITHOUT THE SMELL OF RAW GAS.

NHTSA ID

11173029

Incident

Jan 30, 2019

Mileage

43,000 mi

MY PARTNER TOLD ME THAT HIS PASSENGER HEADLIGHT WAS BURNED OUT AND THAT HE WAS TOLD IT WAS GOING TO BE OVER $800 TO REPLACE. I DECIDED TO TRY TO REPLACE THE BULB MYSELF, BUT I FOUND THAT THE INSULATION ON THE ELECTRICAL HARNESS LEADING THE HEADLIGHT CONNECTORS HAD DETERIORATED TO THE POINT THAT THE WIRES ARE BARE, CAUSING ELECTRICAL SHORTING, EQUIPMENT FAILURE, LEADING TO POTENTIAL ELECTRICAL FIRE WHICH MAY CAUSE SERIOUS LIFE THREATENING ACCIDENTS. I HAVE FOUND AT LEAST ONE OTHER COMPLAINT OF THIS NATURE, REPORTED ON NOVEMBER 13 2017, FOR A 2008 CLK350 VEHICLE WITH THE SAME LEADING VIN NUMBER OF WDBTK56F.... THAT COMPLAINT INDICATES THAT "MERCEDES BENZ IS NOT SUPPLYING A FIX AS REPORTED BY MULTIPLE OWNERS. ALSO EXTENDED WARRANTY INSURERS ARE DENYING COVERAGE DUE TO THE WIDE SPREAD DEFECT ACROSS THE MERCEDES BENZ MODELS." I CANNOT FIND ANY MORE INFORMATION ON THIS PROBLEM. THIS IS NOT NORMAL FOR ANY VEHICLE, MUCH LESS ONE THAT IS ONLY 10 YEARS OLD.

NHTSA ID

11155296

Incident

Nov 30, 2018

TL* THE CONTACT OWNS A 2008 MERCEDES-BENZ CLK350. WHILE THE VEHICLE WAS STATIONARY, THE AIR BAG INDICATOR ILLUMINATED WITHOUT WARNING AND "CHECK SRS AIR BAG" DISPLAYED ON THE INSTRUMENT PANEL. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE THE WIRING FOR BOTH THE DRIVER AND PASSENGER SEATS WERE REPLACED. THE FAILURE RECURRED. A DEALER AND THE MANUFACTURER WERE NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS UNKNOWN.

NHTSA ID

11124551

Incident

Jun 1, 2018

ROUTINE MAINTENANCE IDENTIFIED GASOLINE LEAKING FROM FUEL TANK'S "FUEL SENDER". SMALL CRACK IN PLASTIC FUEL SENDER AT POINT WHERE FUEL HOSE ATTACHED TO SENDER ALLOWED GASOLINE TO ACCUMULATE OVER TIME IN AREA SURROUNDING SENDER AND THEN TRAVEL TO UNDERSIDE OF CAR IN AN AREA IMMEDIATELY ADJACENT TO EXHAUST SYSTEM. AT TIME LEAK WAS DISCOVERED APPROX 1/4 CUP OF FUEL HAD ACCUMULATED. HAD PROBLEM NOT BEEN DISCOVERED A CAR FIRE WAS INEVITABLE

NHTSA ID

11073073

Incident

Feb 15, 2018

Mileage

45,000 mi

ON 12/31/2017 MY CAR WAS PARKED ON DRIVE WAY OF 800 VILLA FLORENCE DR. NAPLES FLORIDA AND WITHOUT ANY PRIOR SIGN OF TROUBLE CAR CUT IN FIRE FROM LEFT SIDE OF TRUNK. THERE WAS NOTHING IN TRUNK OF THIS CAR EXCEPT TO LIGHT WEIGHT BEACH CHAIRS.

NHTSA ID

11067382

Incident

Dec 31, 2017

Mileage

50,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. **NOTE - As of Sept 2025 the pressure testing tool is not finalized and may require modifications to fit properly. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test.