2009 Mercedes-Benz CLK350

The contact owns a 2009 Mercedes - Benz CLK350. The contact stated he turned on the air condition of his vehicle and an odor of mold came from the vents. The vehicle was taken to the dealer and stated that there was no recall for that failure. The manufacturer was contacted, and they also stated that there was no recall for the failure and advised the contact to call the NHTSA Hotline. The failure mileage was 40,030.

NHTSA ID

11480577

Incident

Aug 1, 2022

Mileage

40,030 mi

TL* THE CONTACT OWNS A 2009 MERCEDES BENZ CLK350. THE CONTACT STATED THAT THE FRONT DRIVER SEAT HEADREST AIR BAG EXPLODED WHILE DRIVING, AS A RESULT, THE CONTACT SUSTAINED LOSS OF HEARING IN HER LEFT EAR THAT REQUIRED MEDICAL ATTENTION. THE CONTACT STATED THAT THE VEHICLE'S SOS SYSTEM ALERTED HER OF A FAILURE AND A TOW TRUCK WAS SENT TO THE SCENE. THE VEHICLE WAS TOWED TO RBM OF ALPHARETTA (345 MCFARLAND PKWY, ALPHARETTA, GA 30004) HOWEVER THE FAILURE HAD NOT BEEN DIAGNOSED AS THE DEALER WAS WAITING FOR THE MANUFACTURER TO ADVISE AND SEND A FIELD INSPECTOR TO THE DEALER. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 123,000.

NHTSA ID

11341777

Incident

Jul 22, 2020

Mileage

123,000 mi

TL* THE CONTACT OWNS A 2009 MERCEDES BENZ CLK350. THE CONTACT STATED THAT THE VEHICLE WAS TAKEN FOR STATE EMISSION TESTING AND SHE WAS INFORMED THAT THE VEHICLE WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 19V918000 (VISIBILITY) HOWEVER, PARTS TO DO THE RECALL REPAIR WERE NOT YET AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. NEITHER THE MANUFACTURER NOR THE DEALER WERE MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

NHTSA ID

11331944

Incident

Jul 1, 2020

DRIVING STRAIGHT ABOUT 25MPH ALONG A AN OTHERWISE EMPTY RESIDENTIAL STREET. EXPERIENCED MULTIPLE MICRO-BURSTS OF SUDDEN, BRIEF, VIOLENT, UNINTENDED BRAKING. DRIVER'S FOOT WAS NOWHERE NEAR THE BRAKE PEDAL. BRAKING WAS SO VIOLENT THAT THE WHEELS LOCKED UP AND MADE SKIDDING SOUNDS AND OCCUPANTS WERE SHAKEN. EACH INCIDENCE OF BRAKING WAS VERY SHORT, PERHAPS A FRACTION OF A SECOND. THE FIRST OCCURRENCE (WHILE TRAVELING ~25MPH) THERE WERE ABOUT FOUR SEPARATE "BRAKES" WITHIN A FEW SECONDS. THIS OCCURRED ONLY TWO BLOCKS FROM HOME. I PROCEEDED HOME AT A MUCH SLOWER PACE WITH THE EMERGENCY LIGHTS FLASHING. EN ROUTE I EXPERIENCED SEVERAL MORE INCIDENTS OF SUDDEN, BRIEF, VIOLENT UNINTENDED BRAKING. NO WARNING LIGHTS (E.G. ESP) FLASHED DURING ANY OF THE BRAKING EPISODES. EVEN AT LOW SPEED ON A EMPTY ROAD THE UNINTENDED BRAKING WAS SO VIOLENT AS TO LEAVE ME SHAKEN. IF IT OCCURRED AT HIGH SPEED, ON A BUSY ROAD, AND/OR OF WITH AN INEXPERIENCED DRIVER THE CONSEQUENCES COULD HAVE BEEN SERIOUS.

NHTSA ID

11218056

Incident

Jun 5, 2019

Mileage

75,739 mi

I WAS INVOLVED IN A CAR ACCIDENT LAST FEBRUARY, MY AIRBAG DIDN'T DEPLOY AS COMPARED TO THE OTHER VEHICLE (TOYOTA) WHERE HER AIRBAG WORKED. MY CAR AND THE OTHER PERSON'S CAR WERE TOTALED. I WAS DRIVING ON THE MIDDLE LANE OF A 3 LANE ROAD WHEN THE DRIVER ON THE RIGHT SIDE LANE HIT A PARKED VEHICLE ON THE RIGHT SIDE OF THE ROAD, SPUN AROUND, AND CROSS OVER TO MY LANE AND HIT ME HEAD ON. A ROAD DUE TO MY ACCIDENT, I SUSTAINED A FRACTURE OF MY NECK AND STILL HAVE ONGOING PHYSICAL THERAPY TREATMENTS. *TT *TR

NHTSA ID

11089883

Incident

Feb 19, 2018

Mileage

100,000 mi

THE TPMS CONSTANTLY DISPLAYS FALSE WARNING MESSAGES ABOUT THE TIRES BEING LOW ON PRESSURE. THIS BEGAN ABOUT TWO YEARS AGO, WHEN THE CAR WAS 7 YEARS OLD, 100K MILES. NUMEROUS TRIPS TO THE DEALER AND OTHER REPAIR SHOPS HAS NOT ALLEVIATED THE PROBLEM. TPMS CONSTANTLY GIVING A FALSE WARNING ABOUT LOW TIRE PRESSURE IS A SERIOUS PROBLEM. MUCH LIKE SMOKE ALARMS WHICH GIVE FALSE NOTICE, FALSE TIRE PRESSURE WARNINGS WILL BE IGNORED. THE VEHICLE IS TYPICALLY IN A MOVING CONDITION WHEN THE TPMS ISSUES A FALSE ALERT.

NHTSA ID

11072179

Incident

Jan 1, 2016

Mileage

100,000 mi

TL* THE CONTACT OWNS A 2009 MERCEDES-BENZ CLK350. WHILE OPERATING THE VEHICLE, THE ODOR OF FUEL WAS PRESENT. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE SEAL CONNECTED TO THE FUEL PUMP WAS FAULTY AND THE FUEL PUMP NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 38,000.

NHTSA ID

10955306

Incident

Dec 1, 2016

Mileage

38,000 mi

STRONG FUEL ODOR OUTSIDE OF VEHICLE FOLLOWING FILL UP. MILEAGE 59590.JUST PURCHASED USED WITHOUT EXTENDED WARRANTY.. HAVE NOT TAKEN FOR SERVICE. WILL SEEK INFO PRIOR TO TAKING TO MB SERVICE.

NHTSA ID

10937449

Incident

Dec 24, 2016

Mileage

59,590 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304