2022 Mercedes-Benz EQS 580

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

The vehicle was driving and suddenly lost power, and started driving very slowly, almost causing an accident on the road. I checked for recalls and other vehicles like mine with the same years that have a recall about this issue, where a high-voltage battery shuts down, also, the back seat buckle does not work to buckle my kids

NHTSA ID

11704192

Incident

Nov 27, 2025

I own a 2022 Mercedes EQS 580 electric vehicle which has a high voltage battery for propulsion. On [XXX], in Seoul, Korea, a Mercedes EQE with a high voltage battery made by Farasis Energy spontaneously burst into flames while parked in a garage and not on a charger. The fire totaled the vehicle and caused millions of dollars in property loss. My online research tells me that the high voltage battery in my Mercedes EQS 580 was made by either Farasis Energy or by CATL. I park my vehicle in a garage at home. Were my vehicle to spontaneously burst into flames due to a Farasis Energy battery, my family could die and we would have considerable property damage. Although I have repeatedly asked Mercedes to tell me whether the high voltage battery in my vehicle was made by Farasis Energy or by CATL, it has refused to provide the information. I have no way to obtain the information otherwise and am extremely worried that my family and I are at risk because I have a Farasis Energy battery. Can you please require Mercedes to advise each purchaser of one of its electric vehicles the name of the manufacturer of the high voltage battery in that vehicle so it can take appropriate action to protect itself? Thank you.

NHTSA ID

11610504

Incident

Aug 8, 2024

The incident occurred because the driver's Benz's detection sensor encountered a bug, leading to potential harm to the car occupants. I discovered this bug myself, yet Mercedes-Benz has not compensated me for the issue. I am currently pursuing resolution for this situation.

NHTSA ID

11555729

Incident

Nov 1, 2023

Driving on residential street at 25 miles an hour with no traffic. Car applied emergency brakes which threw everyone forward. Fortunately no other cars behind me. Very dangerous. This has also happened on the main road at 45 miles an hour,

NHTSA ID

11534022

Incident

Jul 23, 2023

I was traveling at 10 mph on a two lane road in clear conditions at 4 p.m. A single car was parked legally ahead on the right and there was a single safety cone present, off the road (on the shoulder) and further ahead on the left. The road was perfectly clear for driving. Without any warning, visual or sound, the autonomous emergency braking system fully engaged and brought the car to a dead stop. The driver information system reported nothing. There was no car behind and no collision occurred. It has left a concern that the autonomous breaking system could be triggered erroneously in the future.

NHTSA ID

11507308

Incident

Feb 14, 2023

THE CAR WAS DELIVERED WITH BRIDGESTONE 265/40R21 XL TURANZA TIRE AND WITH LESS THAN 200 MI. I WAS TOLD THAT THERE IS A BUBBLE ON THE SIDE WALL . WE WERE INFORMED THAT THERE WERE OTHERS WITH THE SAME PROBLEM . I AM BRINGING THIS TO YOUR ATTENTION B/4 THERE ARE MAJOR ACCIDENTS INVOLVED . THANK ING YOU IN ADVANCE TO LOOK INTO THIS

NHTSA ID

11484661

Incident

Sep 14, 2022

Complaint Crackling and cracking noise from the outer wheel on the front axle when cornering Cause The noise is generated by a micromovement on the contact surface between the rim and the brake disk (wheel bolt group) and may be intensified by potential soiling. The more lightweight rim (AMG forged rim) transmits the noise louder; in the case of cast rims, the noise is generally not perceptible. This is not a technical defect, but rather a complaint concerning comfort. Safe operation of the vehicle is ensured at all times. Remedy Important note: The operations described below do not represent a permanent remedy in every case. The noise may reoccur again after an indefinite period of time; sanding the rims with abrasive media multiple times is not permissible. Only cleaning using the Hazet tool 4960-160 (recommendation) can be performed without any concerns each time the wheel is changed or if the complaint reoccurs. Replacing the parts (rim, wheel bolts, wheel bearings, wheel hub, brake disk) is not expedient in the event of this complaint. ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Clean the components of the wheel bolt connection according to the WIS instructions Sand down the rim and brake disk bowl by performing the following steps: • Manually sand rim (old design only) in area of water drain bores (Figure 1; item A), approx. 1.5 cm left and right of water drain bore (Figure 2) Note: Use abrasive paper with grit size 80. The grooving in this area should no longer be visible (sand down approx. 0.1-0.2mm) • Also sand brake disk bowl using emery cloth or abrasive paper with a grain size of 120 • For vehicles equipped with the AMG ceramic brake system (B07), abrasive paper may not be used for cleaning on the brake disk side Note: Do not use any cleaning agent when cleaning on the rim side. Cleaning using abrasive paper with a grain size of 80 will suffice. Do not apply any grease, lubricant or paste after cleaning The brake disk bowl should be "bare metal" in the area of the imprints made by the hole (Figure 3)

A software update is available to enable Plug & Charge at Tesla Superchargers. Schedule a workshop visit with your dealer to receive the update.

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: • The vehicle must be exhibiting the concern as shown in the attachment videos. • The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. • If the geographic location is known, it is very important that it is provided. • Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.

Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. The E505.9 software is released and available in XENTRY Q3 2026.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.