2014 Mercedes-Benz GL350

The contact owns a 2014 Mercedes-Benz GL350. The contact stated that while inspecting the vehicle, there was oil leaking underneath the vehicle. Additionally, the check engine warning light was illuminated while operating the vehicle. The vehicle was taken to the local mechanic who diagnosed the vehicle and determined that the oil cooler seals were faulty and needed to be replaced. The seals were replaced, and the vehicle was repaired. The vehicle was later taken to the local dealer for transmission failure. The manufacturer was notified of the failure. The failure mileage was 140,000.

NHTSA ID

11530486

Incident

Nov 5, 2022

Mileage

140,000 mi

Water has accumulated into the spare wheel well twice causing my ad blue module to be submerged in water, making the system faulty, which then disables the car for use. I have a vehicle that can not start and a repair bill of over 20,000 due to the water accumulation issue. There is a separate recall on other models for this exact problem. This model needs to be included as well.

NHTSA ID

11527566

Incident

May 26, 2023

AS I WAS DRIVING DOWN ON I-27 FROM AMARILLO TO LUBBOCK AT 70 MILES PER HOUR ON 6/22/2020 IN PLEASANT WEATHER AND NO VEHICLES EITHER IN FRONT OF ME OR BESIDE ME, THE MIDDLE PANEL OF THE PANORAMIC SUNROOF SUDDENLY EXPLODED WITH THE GLASS SHATTERING INTO PIECES AND SOME OF THE PIECES DROPPING INTO THE PASSENGER CABIN. THERE WAS NO ROCK STRIKE, HAIL, NOR WAS I TRAVELING THROUGH ANY CONSTRUCTION ZONE. THE AMBIENT TEMPERATURE OUTSIDE WAS 76 F. *TR

NHTSA ID

11330419

Incident

Jun 22, 2020

Mileage

22,000 mi

THE LANE-KEEPING ASSIST ONLY INTERMITTENTLY WORKS. ON OCCASION IT WILL ALERT AND TAKE CORRECTIVE ACTION, BUT EVEN ON SUNNY DAYS WITH CLEARLY DEMARCATED LANES, IT OFTEN DOES NOTHING. IN RESEARCHING THIS ISSUE, THERE ARE SEVERAL OTHER OWNERS WHO HAVE EXPERIENCED THIS AND HAVE SAID THE MERCEDES SERVICE HAS UNOFFICIALLY ACKNOWLEDGED THERE IS A BATCH OF VIN NUMBERS WHICH HAVE FAULTY SENSORS. WE PURCHASED THIS CAR BECAUSE OF THE SAFETY FEATURES AND MERCEDES NEEDS TO DO SOMETHING TO RECTIFY THIS IN ORDER TO KEEP ITS CUSTOMERS SAFE.

NHTSA ID

11162257

Incident

Dec 17, 2018

Mileage

106,000 mi

HAVE A MERCEDES GL 350 WITH ONLY 63000 MILES, HAS MADE A SMALL RATTLE SOUND WHEN FIRST PURCHASED THAT I RELATED TO BEING DIESEL, RATTLE HAS GOTTEN WORSE, TOOK IN TO A MECHANIC WHO STATED TIMING CHAIN, I CALLED MY MERCEDES LOCAL DEALERSHIP AND SERVICE MANAGER STATED HE SPOKE WITH AUTO TECHNICIAN WHO "LAUGHED" WHEN HE HAD TOLD HIM MY CONCERN FOR THE TIMING CHAIN AS THE TECH SAID THIS DOESN'T HAPPEN UNTIL VEHICLES ARE VERY HIGH IN MILES LIKE 200000. THEY EXAMINED MY VEHICLE AND THEN STATED IN FACT IT WAS THE TIMING CHAIN AND QUOTED ME 75000. UPON FURTHER RESEARCH THERE HAS BEEN AN ISSUE WITH OTHERS ON THE INTERNET WITH THE GL 350 2014 SPECIFICALLY NEEDING TIMING CHAIN REPLACEMENT WHEN UNDER LOW MILES. CAR RATTLES WHEN STARTED, WORSE WHEN COLD, CONFIRMED TIMING CHAIN BY LOCAL MERCEDES DEALERSHIP.

NHTSA ID

11102791

Incident

Jun 19, 2018

Mileage

60,000 mi

POWER STEERING WENT OUT WHILE CAR WAS PARKED , DROVE CAR WITHOUT POWER STEERING FOR ABOUT 9 MILES TO GET TO SAFE PLACE. AFTER CAR WAS RESTARTED SEVERAL TIMES STEERING STARTED TO WORK FINE. TOOK CAR TO DEALER FOR CHECK OF PROBLEM BUT THEY COULDN'T TO GET IT TO FAIL AGAIN. TO RESOLVE PROBLEM MERCEDES IS REPLACING THE POWER STEERING UNIT. *TR

NHTSA ID

10638770

Incident

Sep 9, 2014

Mileage

16,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Complaint The customer requests deactivation of the N112/9 HERMES communication module Note: Deactivation of the HERMES control unit (N112/9) is not supported for gray-market vehicles. Cause Before deactivating the HERMES control unit (N112/9), it must be clarified by the legal department of the respective MPC whether and under what conditions deactivation may be carried out. If deactivation is not permissible under applicable law, the HERMES control unit (N112/9) must not be deactivated. Remedy Please inform the customer that, following deactivation, the vehicle will no longer be able to place an automatic emergency call, nor will the customer be able to place a manual emergency call. After deactivation, the Mercedes-Benz Digital Extras will also no longer be available. Please have the attached sample form checked by your market's legal department, adapted to local requirements if necessary, and approved. Furthermore, after informing the customer about the effects of deactivation, please have the workshop complete and sign the approved form together with the customer, and send it to the MPC via a TIPS case for audit-compliant documentation. Furthermore, the workshop must affix a sticker to the emergency call button cover on the overhead control panel and to the emergency call button itself. After affixing, pictures of the overhead control panel need to be attached to the TIPS case for audit-proof documentation. After deactivation, the HERMES control unit (N112/9) is in the "Out of Service" operating status, and the display "SOS NOT READY" appears in the Audio/COMAND system. This display message tells the customer that the emergency call function is not available. In detail, the following steps must be carried out 1. The workshop must inform the customer about the effects of deactivation (see above) 2. Legal review by the MPC Legal department to determine whether deactivation is permissible for the vehicle and provision of a market-specific customer form based on the examples (see "Example - Deactivation communication module HERMES customer declaration English V3.0.pdf") 3. Completion of the market-specific customer form by the workshop and obtaining the customer’s signature 4. Creation of a XSS ticket by the workshop for the MPC with the signed customer form attached 5. Written confirmation of legally reviewed and approved deactivation by the MPC in the TIPS case (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, point 1) 6. Creation of an XSS ticket for documentation of the SA code "09o" (zero nine oh) in the Vehicle Documentation System (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, steps 2–7) 7. Ordering of stickers (part number A9078172900), quantity: 2 8. Affixing of the sticker (part number A9078172900) to the cover of the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 9. Affixing of the sticker (part number A9078172900) to the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 10. Taking photos of the applied stickers and attaching them to the TIPS case 11. After the XSS ticket has been successfully processed, the communication module must be deactivated using XENTRY: • Connect XENTRY Diagnosis • Access the HERMES control unit (N112/9) • "Adaptation" tab, menu item "Teach-in processes" -> "Deactivation" • Follow the instructions

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.