2016 Mercedes-Benz GL350

Spontaneously exploding panoramic sunroof: I was driving northbound on I-5 in Everett, WA, on 27 January 2023 around 7pm. It was clear, the road was dry, it was around 45 degrees, and there was medium traffic. We were going about 65mph. Just myself and my 4 year old daughter were in the car. With no warning and no visible reason there was a gunshot-like sound and then wind (and a crying daughter). I figured out that it was the rear panel of our two-panel sunroof and glass was sprinkling down. Luckily the sunshade roller was holding much of it. We pulled over and checked it out and that is it. Nobody was injured, but there was glass all over my daughter and in her car seat. facts: -2016 GL350 Mercedes; 59500 miles, excellent shape, two-panel panoramic sunroof (front sliding; rear fixed in place) -I have a Packasport 90 rooftop box on low profile Whispbars that covers the entire sunroof with only about a 1.5" gap over the rear glass panel -the box has been on the roof for at least 3 years and the sunroof has not been operated in that time -there have been no modifications to the car besides the rooftop box -it is very, very, very unlikely that a rock could've hit it (although the dealer and insurance don't really want to hear this) -the temperature was normal for January -the highway was smooth and clean and dry -the glass was cratered upward after breaking (may not mean anything) -I was not following a dump truck or a logging truck -I didn't see or hear any rocks or debris in the split second before the breakage My assessment is that the glass shattered of its own accord. I do not know why, but I have seen reports of this on the internet in auto forums.

NHTSA ID

11508928

Incident

Jan 27, 2023

THE EXTERIOR LIGHTING ON THE VEHICLE PROVIDED IS SIGNIFICANTLY INFERIOR IN INTENSITY AND DISTANCE ILLUMINATED. IT IS VERY HARD TO SEE AN OBJECT AFTER FEW FEET AND NIGHT DRIVING BECOMES EXTREMELY DANGEROUS. AT NIGHT IT IS UNSAFE TO DRIVE THIS VEHICLE, WITHOUT BEING ABLE TO SEE THE PASSING CARS OR PEOPLE AND FOLLOWING IS THE REPORT FROM IIHS ON THE ILLUMINATION RESULTS, WHICH WERE TESTED TO BE POOR. HTTP://WWW.IIHS.ORG/IIHS/RATINGS/VEHICLE/V/MERCEDES-BENZ/GLE-CLASS-4-DOOR-SUV/2018 I CONTACTED THE MB USA OFFICE AND THE INFORMED ME THIS IS AS PER DESIGN AND THERE IS NOTHING THEY CAN DO. I SINCERELY RECOMMEND NHTSA TO LOOK INTO THIS ISSUE AND CONDUCT SOME INVESTIGATION INTO IT. THIS WILL PREVENT ANY FATALITY OR SERIOUS CRASH. *TR

NHTSA ID

11092093

Incident

May 31, 2016

TL* THE CONTACT OWNS A 2016 MERCEDES-BENZ GL350. WHILE DRIVING 65 MPH, THE FRONT PASSENGER SEAT BELT FAILED TO RETRACT AFTER THE BRAKE PEDAL WAS DEPRESSED. THE VEHICLE WAS TAKEN TO EDHICKS MERCEDES (3102 S PADRE ISLAND DR, CORPUS CHRISTI, TX 78415), BUT WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED. THE APPROXIMATE FAILURE MILEAGE WAS 16,000. THE VIN WAS NOT PROVIDED. CONSUMER STATED HE HAD BRAKED HARD AND HIS WIFE WAS THROWN AGAINST THE DASHBOARD, BOTH WERE WEARING THEIR SEABELTS. VIN INVALID UPDATED 9/13/18*JB

NHTSA ID

11052207

Incident

Nov 26, 2017

Mileage

16,000 mi

ON SEPTEMBER 6 2017 MY MERCEDES CLUSTER PANAL (ODEMETER) STOPPED WORKING WHILE DRIVING. WHICH THEN I MADE AN APPOINTMENT WITH THE DEALERSHIP AND THEY REPLACED THE ODOMETER WHICH THEN FAILED AGAIN HOURS AFTER PICKING UP THE CAR. AFTER REPLACING IT 3 TIMES UNDER WARRANTY I'M STILL EXPERIENCING THE SAME ISSUE. I CONTACTED MERCEDES CUSTOMER SERVICE AND THEY AIN'T ADDRESSING THE ISSUE PROPERLY AND HAS STOPPED CALLING ME BACK REGARDING THIS MATTER. I HAVE BEEN OUT OF A CAR SINCE SEPTEMBER 6,2017 TILL TODAY WITH NO LOANER VEHICLE FROM MERCEDES. I WAS FORCED TO RENT A CAR UNDER MY OWN EXPENSE WHILE STILL MAKING THE LEASE PAYMENTS ON THE MERCEDES THAT IS NOT SAFE TO DRIVE SINCE I'M NOT ABLE TO KNOW SPEED, GAS, GEAR I'M IN ETC..

NHTSA ID

11044392

Incident

Sep 6, 2017

Mileage

30,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Complaint The customer requests deactivation of the N112/9 HERMES communication module Note: Deactivation of the HERMES control unit (N112/9) is not supported for gray-market vehicles. Cause Before deactivating the HERMES control unit (N112/9), it must be clarified by the legal department of the respective MPC whether and under what conditions deactivation may be carried out. If deactivation is not permissible under applicable law, the HERMES control unit (N112/9) must not be deactivated. Remedy Please inform the customer that, following deactivation, the vehicle will no longer be able to place an automatic emergency call, nor will the customer be able to place a manual emergency call. After deactivation, the Mercedes-Benz Digital Extras will also no longer be available. Please have the attached sample form checked by your market's legal department, adapted to local requirements if necessary, and approved. Furthermore, after informing the customer about the effects of deactivation, please have the workshop complete and sign the approved form together with the customer, and send it to the MPC via a TIPS case for audit-compliant documentation. Furthermore, the workshop must affix a sticker to the emergency call button cover on the overhead control panel and to the emergency call button itself. After affixing, pictures of the overhead control panel need to be attached to the TIPS case for audit-proof documentation. After deactivation, the HERMES control unit (N112/9) is in the "Out of Service" operating status, and the display "SOS NOT READY" appears in the Audio/COMAND system. This display message tells the customer that the emergency call function is not available. In detail, the following steps must be carried out 1. The workshop must inform the customer about the effects of deactivation (see above) 2. Legal review by the MPC Legal department to determine whether deactivation is permissible for the vehicle and provision of a market-specific customer form based on the examples (see "Example - Deactivation communication module HERMES customer declaration English V3.0.pdf") 3. Completion of the market-specific customer form by the workshop and obtaining the customer’s signature 4. Creation of a XSS ticket by the workshop for the MPC with the signed customer form attached 5. Written confirmation of legally reviewed and approved deactivation by the MPC in the TIPS case (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, point 1) 6. Creation of an XSS ticket for documentation of the SA code "09o" (zero nine oh) in the Vehicle Documentation System (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, steps 2–7) 7. Ordering of stickers (part number A9078172900), quantity: 2 8. Affixing of the sticker (part number A9078172900) to the cover of the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 9. Affixing of the sticker (part number A9078172900) to the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 10. Taking photos of the applied stickers and attaching them to the TIPS case 11. After the XSS ticket has been successfully processed, the communication module must be deactivated using XENTRY: • Connect XENTRY Diagnosis • Access the HERMES control unit (N112/9) • "Adaptation" tab, menu item "Teach-in processes" -> "Deactivation" • Follow the instructions

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.